Roland SoundCanvas SC-88 Pro Owner's Manual page 61

Amp Sw (Amp switch)
Turn the Amp Type on/off.
Low Gain
Adjust the gain of the low frequency range.
Hi Gain (High gain)
Adjust the gain of the high frequency range.
#Pan (Output pan)
Adjust the stereo location of the output sound. L63
is far left, 0 is center, and R63 is far right.
Level (Output level)
Adjust the output level.
6: Distortion
This effect produces a more intense distortion than
Overdrive.
L
Distortion
Simulator
R
+Drive
Adjust the degree of distortion.
Amp Type (Amp simulator type)
Select the type of guitar amp.
Small : small amp
BltIn : single-unit type amp
2-Stk : large double stack amp
3-Stk : large triple stack amp
Amp Sw (Amp switch)
Turn the Amp Type on/off.
Low Gain
Adjust the gain of the low frequency range.
Hi Gain (High gain)
Adjust the gain of the high frequency range.
#Pan (Output pan)
Adjust the stereo location of the output sound. L63
is far left, 0 is center, and R63 is far right.
Level (Output level)
Adjust the output level.
Effects that modulate the sound (modula-
tion type)
7: Phaser
A phaser adds a phase-shifted sound to the original
sound, producing a twisting modulation that creates
spaciousness and depth.
Off/On [3]
-12 - +12 [17]
-12 - +12 [18]
L63 - 0 - R63 [19]
0 - 127 [20]
[01H, 11H]
Amp
EQ
Pan
0 - 127 [1]
Small/BltIn/2-Stk/3-Stk [2]
Off/On [3]
-12 - +12 [17]
-12 - +12 [18]
L63 - 0 - R63 [19]
0 - 127 [20]
[01H, 20H]
Chapter 4. Insertion Effects
Phaser
L
R Phaser
+Manual
Adjust the basic frequency from which the sound
will be modulated.
#Rate
Adjust the frequency (period) of modulation.
Depth
Adjust the depth of modulation.
Reso (Resonance)
Adjust the amount of emphasis added to the fre-
quency range surrounding the basic frequency
determined by the Manual parameter setting.
Mix (Mix level)
Adjust the ratio with which the phase-shifted sound
is combined with the direct sound.
Low Gain
Adjust the gain of the low frequency range.
Hi Gain (High gain)
Adjust the gain of the high frequency range.
Level (Output level)
Adjust the output level.
8: Auto Wah
The Auto Wah cyclically controls a filter to create cyclic
change in timbre.
L
Wah
R
Fil Type (Filter Type)
Select the type of filter.
LPF : The wah effect will be applied over a
wide frequency range.
BPF : The wah effect will be applied over a
narrow frequency range.
Sens (Sensitivity)
Adjust the sensitivity with which the filter is con-
trolled. If this value is increased, the filter frequency
will change more readily in response to the input
level.
+Manual
Adjust the center frequency from which the effect is
applied.
EQ
EQ
100 - 8.0k [1]
0.05 - 10.0 [2]
0 - 127 [3]
0 - 127 [4]
0 - 127 [5]
-12 - +12 [17]
-12 - +12 [18]
0 - 127 [20]
[01H, 21H]
EQ
Pan
LPF/BPF [1]
0 - 127 [2]
0 - 127 [3]
59