Roland SoundCanvas SC-88 Pro Owner's Manual page 90

RT H Slow (RT High Frequency Slow Rate)
Adjust the speed of the high-range rotor for the low-
speed (Slow) setting.
RT H Fast (RT High Frequency Fast Rate)
Adjust the speed of the high-range rotor for the
high-speed (Fast) setting.
RT Hi Accl (RT High Frequency Acceleration)
Adjust the time over which the rotation speed of the
high-range rotor will change from low-speed to
high-speed (or high-speed to low-speed) rotation.
Smaller values will require greater time to reach the
new rotational speed.
RT Hi Lev (RT High Frequency Level)
Adjust the volume of the high-range rotor.
RT Sept (RT Separation)
Adjust the spatial spread of the rotary sound.
#RT Speed
Simultaneously switch the rotational speed of both
the low-range and the high-range rotors.
Slow : Slow down the rotation to the speci-
fied speeds (RT L Slow parameter /
RT H Slow parameter values).
Fast : Speed up the rotation to the specified
speeds (RT L Fast parameter / RT H
Fast parameter values).
RT Pan (RT Output Pan)
Adjust the stereo position of the rotary sound. L63
is far left, 0 is center, and R63 is far right.
RT Level
Adjust the volume of the rotary sound.
Level (Output level )
Adjust the output level.
61: OD / Phaser(Overdrive/Distortion, Phaser)
This connects an overdrive or distortion in parallel with
a phaser.
Overdrive/
L
Distortion
R
Phaser
<OD (Overdrive/Distortion)>
OD Sel (OD Select)
Select either Overdrive or Distortion.
88
0.05 - 10.0 [10]
0.05 - 10.0 [11]
0 - 15 [12]
0 - 127 [13]
0 - 127 [14]
Slow/Fast [15]
L63 - 0 - R63 [18]
0 - 127 [19]
0 - 127 [20]
[11H, 05H]
Pan
Pan
Odrv/Dist [1]
Chapter 4. Insertion Effects
+OD Drive (OD Drive)
Adjust the depth of distortion. The volume will
change together with the depth of distortion.
OD Amp (OD Amp Simulator Type)
Select the type of guitar amp.
Small : small amp
BltIn : single-unit type amp
2-Stk : large double stack amp
3-Stk : large triple stack amp
OD Amp Sw (OD Amp Switch)
Turn the OD Amp parameter on/off.
OD Pan (OD Output Pan)
Set the stereo location of the overdrive or distortion
sound. L63 is far left, 0 is center, and R63 is far
right.
OD Level
Adjust the overdrive or distortion volume.
<PH (Phaser)>
PH Man (Phaser Manual)
Adjust the center frequency at which the sound will
be modulated.
#PH Rate (Phaser Rate)
Adjust the modulation speed.
PH Depth (Phaser Depth)
Adjust the modulation depth.
PH Reso (Phaser Resonance)
Adjust the emphasis for the region around the cen-
ter frequency specified by the PH Man parameter.
PH Mix (Phaser Mix Level)
Adjust the proportion of the phase-shifted sound
that will be mixed with the direct sound.
PH Pan (Phaser Output Pan)
Set the stereo location of the phaser sound. L63 is
far left, 0 is center, and R63 is far right.
PH Level
Adjust the volume of the phaser sound.
Level (Output level )
Adjust the output level.
62: OD / AutoWah (Overdrive/Distortion, Auto-wah)
This connects an Overdrive or Distortion in parallel
with an Auto-wah.
Overdrive/
L
Distortion
R
Auto Wah
0 - 127 [2]
Smal/BltIn/ 2-Stk/3-Stk [3]
Off/On [4]
L63 - 0 - R63 [16]
0 - 127 [17]
100 - 8.0k [6]
0.05 - 10.0 [7]
0 - 127 [8]
0 - 127 [9]
0 - 127 [10]
L63 - 0 - R63 [18]
0 - 127 [19]
0 - 127 [20]
[11H, 06H]
Pan
Pan