Phone Parameters - Bosch D7212GV3 Program Entry Manual

D7212GV3 | Program Entry Guide | 2.0
Keypad Programming of Phone #
D1255
1. Refer to Figure 1 on page 6 to access Keypad
Programming and navigate to the PHONE
NUMBERS option.
2. At the PHONE 1 - 4 prompt, enter the phone
number you wish to configure and press [ENT].
The current phone number shows.
If the current phone number is longer
than 20 characters, use the [PREV] and
[NEXT] keys to view the additional
characters.
3. Press [ENT] to change the phone number.
4. The [PREV] button acts as a [Backspace] key
and the [COMMAND] key scrolls through special
characters. Press [PREV] to delete the
characters of the phone number, and then enter
the new phone number. Press [COMMAND] to
cycle through the special dialing characters
{*, #, C, D}, then press [NEXT] to choose a
character.
5. Press [ENT] to save the phone number.
6. When the keypad reads PARAMETER SAVED,
your selection has been configured.
D1260
1. Refer to Figure 2 on page 7 to access Keypad
Programming and navigate to the Phone
Numbers option and press the corresponding
softkey.
2. At the Phone (1-4) prompt, enter the phone
number you wish to configure and press
[ENTER]. The current phone number shows.
If the current phone number is longer
than 20 characters, the Previous and
Next softkeys appear. Use the softkeys to
scroll to view the additional characters.
3. Press the Edit softkey to change the phone
number.
4. Pause (3 sec pause - "C") and DT Detect (Dial
Tone Detect - "D") softkeys enter special
characters. The Backspace softkey allows you
to erase characters. The Clear softkey allows
you to clear the entire phone number. The
[COMMAND] and [ENTER] keys allow you to
enter an * or a #. Use the softkeys, the number
buttons, and the [COMMAND] and [ENTER] keys
on the keypad to enter the new phone number.
5. Press the Save softkey.
When the keypad reads Parameter Saved, your
selection has been configured.
Bosch Security Systems, Inc. | 10/11 | F01U170808-02
Panel and Area Wide Parameters
2.2

Phone Parameters

The program items in this category describe panel-
wide characteristics for telephone dialing, receiver
format, and supervision.
Phone # Format
Default:
Selection:
Modem
2
IIIa
Contact ID
Central Station Receiver Format for Transmission
of Reports: Phone # Format provides many
reporting advantages over the Contact ID format.
Refer to the central station receiver Report Directory
(P/N: 74-04651-001) for more information about the
effect of reporting formats.
Reports identify points as 001 through 040 and
passcode User ID codes as 000 through 099 at the
central station receiver (unless Point/User Flag is
programmed Yes; refer to the Point/User Flag
prompt in this section). When reporting point events,
2
Modem IIIa
text to the central station receiver as programmed in
Point Assignments.
Keypad Programming of Phone # Format
D1255
1. Refer to Figure 1 on page 6 to access Keypad
Programming and navigate to the PHONE
PARAMETERS option.
2. At the PHONE 1 - 4 prompt, enter the phone
route number you wish to configure and press
[ENT].
3. Press [NEXT] or [PREV] to toggle between
Contact ID and ModemIII
select the desired phone format.
When the keypad reads PARAMETER SAVED, your
selection has been configured.
D1260
1. Refer to Figure 2 on page 7 to access Keypad
Programming and navigate to the Phone
Parameters option and press the corresponding
softkey.
2. At the Phone (1-4) prompt, enter the phone route
number you wish to configure and press
[ENTER]. The current configuration shows.
3. Press the Edit softkey to change the phone
format.
4. Select the softkey for the option to which you
wish to change. Press the Save softkey
2
Modem IIIa
2
Modem IIIa or Contact ID
2
Modem IIIa Communication
Format
ANSI-SIA Contact ID
Communication Format also sends point
2
and press [ENT] to
EN | 9