Buell 2007 FIREBOLT Service Manual page 235

HOME
PINION SHAFT BEARINGS
Pinion shaft journal diameter
Outer race diameter in right
crankcase
Bearing running clearance
Fit in cover bushing (loose)
TORQUE VALUES
ITEM
Air scoop fastener at oil cooler
All tie bars
Anti-rotation screws (lifter)
Center tie bar mount to engine
fasteners
Clutch cable wire form retainer
Crankcase 5/16 in. screws
Cylinder head screws
Cylinder studs
Exhaust header nuts
Feed oil line at rear of oil
pump
Front isolator bolt
Front isolator bracket mount-
ing fasteners
Gearcase cover screws
Oil line clamp
Oil cooler feed oil line at oil
cooler
Oil cooler feed oil line at oil
pump
Oil cooler line clamp
Oil cooler return oil line at
crankcase
Oil cooler return oil line at oil
cooler
Oil cooler to V-bracket mount
Oil filter adapter
Oil line clamp at starter motor
Oil line fittings at swingarm
3-4 2007 Buell Firebolt: Engine
Table 3-15. Pinion Shaft Bearing Specifications
NEW COMPONENTS
1.2496-1.2500 in.
1.5646-1.5652 in.
0.00012-0.00088 in.
0.0023-0.0043 in.
TORQUE
48-72 in-lbs
25-27 ft-lbs 33.9-36.6 Nm
55-65 in-lbs
30-33 ft-lbs 40.6-44.7 Nm
84-92 in-lbs 9.5-10.4 Nm
15-19 ft-lbs
Special proce-
dure
10-20 ft-lbs
72-96 in-lbs 8.1-10.8 Nm
27-29 ft-lbs 36.6-39.3 Nm
49-51 ft-lbs 66.4-69.1 Nm
49-51 ft-lbs 66.4-69.1 Nm
80-110 in-lbs
12-36 in-lbs
19-21 ft-lbs
22-24 ft-lbs 29.8-32.5 Nm
12-36 ft-lbs
15-17 ft-lbs
19-21 ft-lbs 25.8-28.5 Nm
96-108 in-lbs 10.8-12.2 Nm
96-144 in-lbs
40-50 in-lbs
108-156 in-lbs
31.7398-31.7500
1.2496 in. (min)
mm
39.7408-39.7561
1.5672 in. (max)
mm
0.00305-0.02235
mm
0.0584-0.1092 mm
5.4-8 Nm LOCTITE 271 (red), page 3-76
page 3-14
6-7 Nm page 3-88
page 3-29
page 3-15, 3-39
20-26 Nm LOCTITE 271 (red), page 3-106
Special pattern to tighten, page 3-58
14-27 Nm Special method to tighten, page 3-107
page 3-14
page 3-35
page 3-14
page 3-14, 3-32
9-12 Nm Special pattern to tighten, page 3-93
1.3-4.5 Nm page 3-76
26-28 Nm page 3-37, 3-76
page 3-37
1-4 Nm page 3-37
20.3-23 Nm page 3-37
page 3-37, 3-76
page 3-76
11-16 Nm LOCTITE 243 (blue), page 3-86
5-5.5 Nm page 3-35
12-17.6 Nm page 3-74
SERVICE WEAR LIMITS
31.7398 mm (min)
39.8069 mm (max)
0.0050 in. 0.1270 mm
NOTES