General - Buell 2007 FIREBOLT Service Manual

HOME

GENERAL

SERVICING A NEW MOTORCYCLE
1 1
WARNING WARNING
Perform the service and maintenance operations as indi-
cated in the regular service interval table. Lack of regular
maintenance at the recommended intervals can affect
the safe operation of your motorcycle, which could result
in death or serious injury. (00010a)
Service operations to be performed before customer delivery
are specified in the applicable model year PREDELIVERY
AND SETUP MANUAL.
The performance of new motorcycle initial service is required
to keep warranty in force and to ensure proper emissions sys-
tems operation. See 1.3 MAINTENANCE SCHEDULE
details.
SAFE OPERATING MAINTENANCE
NOTES
Do not attempt to retighten engine head bolts. Retighten-
ing can cause engine damage.
During the initial break-in period, use only Harley-David-
son 20W50 engine oil. Failure to use the recommended
oil will result in improper break-in of the engine cylinders
and piston rings.
A careful check of certain equipment is necessary after peri-
ods of storage, and frequently between regular service inter-
vals, to determine if additional maintenance is required.
Check:
1. Tires for abrasions, cuts and correct pressure.
2. Secondary drive belt for proper tension and condition.
3. Brakes, steering and throttle for responsiveness.
4. Brake fluid level and condition. Hydraulic lines and fit-
tings for leaks. Also, check brake pads and rotors for
wear.
5. Cables for fraying, crimping and free operation.
6. Engine oil and transmission fluid levels.
7. Headlamp, passing lamp, tail lamp, brake lamp and turn
signal operation.
SHOP PRACTICES
Repair Notes
NOTE
General maintenance practices are given in this section.
Repair = Disassembly/Assembly.
Replace = Removal/Installation.
All special tools and torque values are noted at the point of
use.
All required parts or materials can be found in the appropriate
PARTS CATALOG.
Safety
Safety is always the most important consideration when per-
forming any job. Be sure you have a complete understanding
of the task to be performed. Use common sense. Use the
proper tools. Protect yourself and bystanders with approved
eye protection. Don't just do the job – do the job safely.
Removing Parts
Always consider the weight of a part when lifting. Use a hoist
whenever necessary. Do not lift heavy parts by hand. A hoist
and adjustable lifting beam or sling are needed to remove
some parts. The lengths of chains or cables from the hoist to
the part should be equal and parallel and should be posi-
tioned directly over the center of the part. Be sure that no
for obstructions will interfere with the lifting operation. Never
leave a part suspended in mid-air.
Be sure to check capacity rating and condition of hoists,
slings, chains and cables before use. Exceeding capac-
ity ratings or using lifting devices that are in poor condi-
tion can lead to an accident, which could result in death
or serious injury. (00466b)
Always use blocking or proper stands to support the part that
has been hoisted. If a part cannot be removed, verify that all
bolts and attaching hardware have been removed. Check to
see if any parts are in the way of the part being removed.
When removing hoses, wiring or tubes, always tag each part
to ensure proper installation.
Cleaning
If you intend to reuse parts, follow good shop practice and
thoroughly clean the parts before assembly. Keep all dirt out
of parts; the unit will perform better and last longer. Seals, fil-
ters and covers are used in this vehicle to keep out environ-
mental dirt and dust. These items must be kept in good
condition to ensure satisfactory operation.
Clean and inspect all parts as they are removed. Be sure all
holes and passages are clean and open. After cleaning,
cover all parts with clean lint-free cloth, paper or other mate-
rial. Be sure the part is clean when it is installed.
Always clean around lines or covers before they are removed.
Plug, tape or cap holes and openings to keep out dirt, dust
and debris.
Disassembly and Assembly
Always assemble or disassemble one part at a time. Do not
work on two assemblies simultaneously. Be sure to make all
necessary adjustments. Recheck your work when finished.
Be sure that everything is done.
Operate the vehicle to perform any final check or adjust-
ments. If all is correct, the vehicle is ready to go back to the
customer.
2007 Buell Firebolt: Maintenance
1 1
WARNING WARNING
1.1
1-1