Smart Hub Indicators And Connectors; Icomfort Smart Hub Normal Condition; Center Push Button Indicator - Lennox iComfort S30 Installation And Setup Manual

Smart Hub Indicators and Connectors

SMART HUB INDICATOR DISPLAY LOCATION
Five indicators are located on the front of the Smart
Hub enclosure (near the top edge). One indicator
location is reserved for future expansion and has
no icon and no current function. The other four lo­
cations have icons depicting Smart Hub functions
and are back-lit by LEDs. From left to right:
WI-FI – INDICATES THE STATUS OF THE INTERNAL WI-FI MODULE AND
WHETHER OR NOT IT IS CONNECTED TO THE HOME WI-FI NETWORK.
THERMOSTAT – INDICATES THE STATUS OF THE THERMOSTAT MAG-MOUNT
AND HD DISPLAY AND WHETHER OR NOT THE SMART HUB CAN COMMUNICATE
WITH THE HD DISPLAY.
HVAC – SHOWS THE STATUS OF THE HVAC EQUIPMENT IN THE HOME CON­
TROLLED BY THIS SMART HUB, AND WHETHER OR NOT THE SMART HUB
CAN COMMUNICATE WITH THEM.
ALERT – SHOWS IF THERE IS A CRITICAL ALERT CONDITION.
Figure 13. Smart Hub Indicators and Connectors
These LEDs have a red LED chip and a green LED chip in the package and
can show red, green, or amber colors, steady or flashing.

iComfort Smart Hub Normal Condition

* SMART-HUB WI-FI is a self-contained Wi-Fi network (peer-to-peer)
hosted by the SMART-HUB and totally independent of any other local
network. SMART-HUB WI-FI is used to connect multiple SMART-HUBs
and mobile devices running either the iComfort Thermostat or Mobile
Setup applications. If multiple SMART-HUBS are installed, access to on­
ly one is required to control the entire system.
As a general rule:
S
Unlit indicators show there is no power to the Smart Hub or its software has
suffered a critical initialization error.
S
Steady amber indicators show Smart Hub boot up and self-check
processes are in progress or have completed. Boot up and self checks
normally complete rapidly, so amber indicators may appear only briefly
(except for the Wi-Fi indicator).
S
Flashing amber Wi-Fi indicator shows that the Wi-Fi module check is in
progress. Steady amber Wi-Fi indicator shows that the Wi-Fi module has
passed its check but is not connected to the home Wi-Fi network.
The Smart Hub using spring
loaded push connectors for
S
Flashing green indicators show acquisition and test of resources across
wiring connections.
wired interfaces to the Mag-Mount / HD Display and to installed HVAC
equipment
S
Steady green indicators show that the associated function is connected
and operating normally.
S
Flashing red indicators show a problem with the associated function.
S
Flashing red ALERT indicator shows that a critical alert condition exists. If
one of the other indicators is also flashing red, that is the likely source of
the alert. If no other indicators are flashing red, the source of the alert is
not defined.

Center Push Button Indicator

The center push button has a RGB (red-green-blue) LED backlight that
indicates the Lennox-managed local network communication status of the
Smart Hub, and if the Smart Hub is transferring a software image from a flash
drive plugged into the USB port. While this LED indicator can show any color,
it is currently limited to amber, green, or blue.
When the Smart Hub is in a normal steady state, -- when the Smart Hub is
in normal day-to-day operation -- the center push button backlight shows:
S
Steady blue when there is one or more Smart Hubs in the home and they
are not connected to a mobile device running a iComfort Mobile Setup
application.
S
Steady blue when there is one or more Smart Hubs in the home, but not
interconnected.
S
Steady blue when one or more Smart Hubs are interconnected in the home
through a Lennox-managed local network.
During various Smart Hub transient states -- when the Smart Hub is engaged
in a special task that should complete soon -- the center push button backlight
shows:
16