Smart Hub Indicators And Connectors - Lennox iComfort S30 Installation And Setup Manual

The identity of devices requesting connection to a Smart Hub is rigorously
authenticated before connection is allowed to ensure that only iComfort
devices connect to a Smart Hub.

Smart Hub Indicators and Connectors

SMART HUB INDICATOR DISPLAY LOCATION
Five indicators are located on the front of the Smart Hub
enclosure (near the top edge). One indicator location is
reserved for future expansion and has no icon and no
current function. The other four locations have icons
depicting Smart Hub functions and are back-lit by
LEDs. From left to right:
WI-FI – INDICATES THE STATUS OF THE INTERNAL WI-FI MODULE AND WHETHER OR
NOT IT IS CONNECTED TO THE HOME WI-FI NETWORK.
THERMOSTAT – INDICATES THE STATUS OF THE THERMOSTAT MAG-MOUNT AND HD
DISPLAY AND WHETHER OR NOT THE SMART HUB CAN COMMUNICATE WITH THE HD
DISPLAY.
HVAC – SHOWS THE STATUS OF THE HVAC EQUIPMENT IN THE HOME CONTROLLED
BY THIS SMART HUB, AND WHETHER OR NOT THE SMART HUB CAN COMMUNICATE
WITH THEM.
ALERT – SHOWS IF THERE IS A CRITICAL ALERT CONDITION.
Figure 12. Smart Hub Indicators and Connectors
These LEDs have a red LED chip and a green LED chip in the package and can
show red, green, or amber colors, steady or flashing.
As a general rule:
S
Unlit indicators show there is no power to the Smart Hub or its software has
suffered a critical initialization error.
S
Steady amber indicators show Smart Hub boot up and self-check processes
are in progress or have completed. Boot up and self checks normally complete
rapidly, so amber indicators may appear only briefly (except for the Wi-Fi
indicator).
S
Flashing amber Wi-Fi indicator shows that the Wi-Fi module check is in
progress. Steady amber Wi-Fi indicator shows that the Wi-Fi module has
passed its check but is not connected to the home Wi-Fi network.
®
S30
The Smart Hub using spring loaded
push connectors for wiring
connections.
S
Flashing green indicators show acquisition and test of resources across wired
interfaces to the Mag-Mount / HD Display and to installed HVAC equipment
S
Steady green indicators show that the associated function is connected and
operating normally.
S
Flashing red indicators show a problem with the associated function.
S
Flashing red ALERT indicator shows that a critical alert condition exists. If one
of the other indicators is also flashing red, that is the likely source of the alert.
If no other indicators are flashing red, the source of the alert is not defined.
CENTER PUSH BUTTON INDICATOR
The center push button has a RGB (red-green-blue) LED backlight that indicates
the Lennox-managed local network communication status of the Smart Hub, and
if the Smart Hub is transferring a software image from a flash drive plugged into
the USB port. While this LED indicator can show any color, it is currently limited to
amber, green, or blue.
When the Smart Hub is in a normal steady state, -- when the Smart Hub is in
normal day-to-day operation -- the center push button backlight shows:
S
Steady blue when there is only one Smart Hub in the home and it is not
connected to a mobile device running a iComfort
S
Steady blue when there is more than one Smart Hub in the home, but this
Smart Hub is not connected to any other Smart Hub.
S
Steady green when the Smart Hub is connected to another Smart Hub in the
home through a Lennox-managed local network.
During various Smart Hub transient states -- when the Smart Hub is engaged in
a special task that should complete soon -- the center push button backlight shows:
S
Steady amber (briefly) while the Smart Hub conducts self tests and boots up.
S
Flashing amber while software or firmware updates for an iComfort
system component or a connected field-upgradable HVAC asset is being
transferred from files on a flash drive plugged into the Smart Hub USB port.
S
Steady blue while the Smart Hub conducts checks on its internal Wi-Fi module
and remote HVAC assets. (Icon indicators show progress.)
S
Flashing green when the Smart Hub is attempting a Lennox-managed local
network connection with another Smart Hub in the home or with a mobile
®
device running the iComfort
S
Steady green when the Smart Hub is connected to a mobile device running the
®
iComfort S30 service maintenance application through a Lennox-managed
local network connection. (This is considered a transient state because the
mobile device will disconnect from the Lennox-managed network when the
task at hand is complete.)
12
®
S30 application.
S30 service maintenance application.
®
S30