Partial Icomfort® System - Icomfort® Equipment Interface Module - Lennox iComfort S30 Installation And Setup Manual

®
Partial iComfort System — iComfort
®
The iComfort Equipment Interface Module (EIM) can be configured in the
following setups:
S
®
iComfort Wi-Fi , iComfort
non-communicating (conventional) indoor unit and iComfort
S
®
iComfort Wi-Fi , iComfort
non-communicating (conventional) indoor unit and outdoor unit.
S
® ®
iComfort Wi-Fi , iComfort
non-communicating heat pump
1. Wiring—See Communicating System and Optional Accessories
Wiring diagrams.
S
4-conductor thermostat wire between the HD Display, Smart-Hub and
equipment interface module (R, i+, i-, C).
S
4-conductor thermostat wire from the iComfort
heat pump (R, i+, i-, C).
S
Up to 8-conductor thermostat wire from the non-communicating
furnace terminal strip to the equipment interface module (R, C, O, Y1,
Y2, G, W1, W2 and W3).
S
Wiring as required for accessories
2. DO NOT cut any option link on furnace control.
3. After the entire system is wired, power up the system; the iComfort
will check the system for installed communication devices.
___________________________________________________________________________________________________________________________
An outdoor temperature sensor is provided in all iComfort
display the outdoor temperature on the home screen of the HD Display, you can
enable this feature under the dealer control center. Use the following procedure
to enable the outdoor temperature sensor display.
1. Touch Menu and then press settings.
2. Touch advanced settings and then press view dealer control center.
3. Touch equipment and then press thermostat.
4. Touch Outdoor Temperature and touch sensor. Touch the back arrow
(<) at the top left-hand of the screen to return to the dealer control
center.
®
Equipment Interface Module
®
Equipment Interface Module with either a
®
Equipment Interface Module with either a
®
furnace, iComfort Equipment Interface and a
®
S30 to the iComfort
®
outdoor units. To
HOME screen menu icon
4. During the Installer System Setup (see page 19) you will arrive at the
equipment found screen. From there touch non-communicating
equipment to add non-communicating equipment.
5. From the add/remove equipment screen, touch either 1 Stage A/C unit
®
outdoor unit.
or 2 Stage A/C unit.
6. Touch the done to return to the equipment found screen. Touch
continue to proceed to the next screen.
7. Continue with the installer setup sequence. When the set up airflow per
zone screen appears here you can adjust blower, heating and cooling
circulation air flows. When done, press continue to proceed.
8. The dealer control center will appear. Touch tests to access the test
section
9. Here you will have another opportunity to adjust blower circulation, heating
and cooling circulation air flows. Use the plus or minus buttons to adjust up
or down the CFM settings. Once adjustments are completed, press
continue.
10. Under the touch test to run, you may un-check any test not required, or
run all tests. Touch start tests to proceed. Once each test section is
completed, press continue to proceed to the next group of tests.
11. Once all test are completed, press done. This will return you to the touch
tests to run screen. If finish, press the back arrow (<) at the top left-hand
of the screen to return to the dealer control center.
®
S30
12. Touch exit to return to the home screen.
TIPS
5. Touch exit to return the home screen.
To enable the Indoor Humidity Display on the Home screen use the following
procedure:.
1. Touch Menu and then press settings.
2. Touch advanced settings and then press view dealer control center.
3. Touch equipment and then press thermostat.
4. Touch Display Indoor Humidity and press the toggle switch to turn on.
Touch the back arrow (<) at the top left-hand of the screen to return to
the dealer control center.
5. Touch exit to return the home screen.
Turn the Indoor humidity display on and off in a similar manner as above.
41