Using The Interval Frame Function - Sony SRW-9000PL Operation Manual

Using the Interval Frame Function

1
Make system settings.
Select the target frame frequency (24, 25, or
30PsF), and select the recording format and
picture quality (4:2:2, 4:4:4 SQ, 4:4:4 HQ, or
4:4:4 HQ 12bit).
Example settings: Settings for 24 frames of
target frame frequency (23.98PsF) and
4:2:2 recording format and picture
quality.
1 Carry out steps 1 and 2 of "To set with
FORMAT" (page 85) in "Selecting the
System Signal Format".
2 Set as shown below, according to the
camera system format.
S Y S T E M S e t u p
FORMAT
REFERENCE
TEST SG
LCD
KEYMAP
KEYINHI
REMOTE/LOCAL
SERVO
REC INHI
EDIT
POWER
BATTERY
OTHERS
SRW-9000PL(E)
3 In the submenu window, select [SET].
The format of the unit is switched, and
"S59P(23PsF)" appears in the display
(for about 30 seconds).
dB
SDI SDI SDI
0
-10
-20
-30
-60
EMP EMP EMP
EE
L R L R L R
1 2 3
STBY OFF
TCG
01 01
H
12.2V REMAIN
- - -
The S in S59P indicates that SR
Motion is enabled. (SELECT FPS is
set to "VTR", and the Interval Frame
function is used.) The 59P indicates
that FPS FORMAT is set to 59.94P.
(23PsF) indicates that the target frame
frequency is 23.98PsF.
116 Interval Frame Function
Si gnal For m at
LINE 1080P
FRAME 23.98
SIGNAL 4:2:2
SELECT FPS ON
MAP
FPS FORMAT 59/60
[SET]
OFF
C A S S O U T 00:00:00:00
TC R
SDI SDI SDI SDI SDI SDI SDI SDI
EMP EMP EMP EMP EMP EMP EMP EMP
L R L R L R L R L R L R L R L R
4 5 6 7 8 9 10 11
1 2 SRW-9000P
KEYINHI
51 11
M S
IN: --:--:--:--
1080
LOCAL
CH.COND
S59P
EE
(23PsF)
17:11
4:2:2
To make the timecode continuous
Make the following settings in the TC Setup
menu.
RUN MODE: R RUN (Rec Run)
TCG MODE: PRST (Preset) or RGN
(Regen), both are available.
REGEN SOURCE: INT L (Internal LTC)
(following the timecode recorded on the
tape)
For details on the TC Setup menu, "TC
(Timecode) Setup Menu" (page 173).
2
Set the frame interval (FRM).
1 Exit the menu, and press the SELECT/
ENTER dial with the FUNC button
held down in the HOME screen.
The popup window displays the
current frame interval (FRM), the
current number of frames (FPS), and
the playback speed.
dB
ANA ANA
0
-10
-20
-30
-60
EMP EMP
PB
L R L R
1 2
OOOO
TCG LTC INTRP
00
INDLY:
LTC
SYS : 1080 S59P(23PsF) 4:2:2
FRM : 8 / 8 F R M ( M O D E : V T R )
MEM : 2 1 %
Playback speed
SDI (times normal playback speed)
EMP
L R
12
When you press the SELECT/ENTER
L(E)
dial with the FUNC button held down
RECINHI
and do not perform any operation for
three seconds, the screen returns to the
F
previous state. When you press the
SELECT/ENTER dial with the FUNC
button held down and press the
SELECT/ENTER dial again with the
FUNC button held down, the following
screen appears. This screen remains on
the display even if you do not perform
any operation for three seconds or
more.
SDI SDI SDI SDI SDI SDI SDI SDI
SR Motion Recording
EMP EMP EMP EMP EMP EMP EMP EMP
SYSTEM : 23.98PsF
L R L R L R L R L R L R L R L R
SEL-FPS : 59.94P
3 4 5 6 7 8 9 10
MODE : VTR
SIGNAL : 6 FRM
SRW-9000PL(E)
PLAY LOCK
MEMORY : 21 %
DF EXT-LK KEYINHI
FRM
6
FRM
00 00 00
FPS
10.000
FPS
H [ x 2.400 ] M S
IN: --:--:--:--
VITC AU
12.8V
Number of frames (FPS)
Frame Interval (FRM)
A/E A/E
EMP EMP
L R L R
11 12
RECINHI
F
50min