Furuno GS-100 Operator's Manual page 96

APPENDIX 1 MENU TREE
1
├ Backup
│ ├
Backup User Setting (Yes, No )
│ ├
Load User Setting (Yes, No )
├ SW/Database Update*
│ ├ Chk the Available Software
│ │ │ │ ├ ├
│ │ ├
│ │ └
│ └ Chk the New Data Table
│ ├
│ └
├ Exchange*
│ ├ Display Unit
│ │ │ │ ├ ├
│ │ └
│ ├ Sensor Unit
│ │ ├
│ │ ├
│ │ ├
│ │ └
│ ├ Serial No.
│ │ └ └
Destination Language (English , Destination Language (English
└ Sensor Status* (Open the sensor status window.)
5 I/O
├ Output Data1 to 4
│ ├
Format (IEC 61162-1 Ed.4 , IEC 61162-1 Ed.3, NMEA V2.0, NMEA V1.5)
│ ├ BPS (4800 bps, 38400 bps)**
│ │
│ │ └ └ Sentence (HDT: Off , HRM: Off , ROT: Off , THS: 0.2s ***, VBW: 1s , VLW: 1s , S t
│
VTG: 1s , ZDA: 1s , GPatt: Off , GPhve: Off ) ***: 0.020s for Output Data4.
├ Ethernet
│ ├
Sentence (HDT: 0.1s , HRM: 0.1s , ROT: 0.1s , THS: 0.020s , VBW: 1s , VLW: 1s ,
│ │
VTG: 1s , ZDA: 1s , GPatt: 0.020s , GPhve: 0.020s )
│ ├ SFI*
│ └ IP ADR/Port*
├ Data Source Select
│ │ ├ ├
HDG (D t 1 D t 2 D t 4 Eth HDG (Data1, Data2, Data4, Ethernet, CAN , User Priority)
│ ├
Ext. STW/COG/SOG (Data1 , Data2, Data4, Ethernet, CAN, User Priority)
│ ├
Ext. CUR (Data1 , Data2, Data4, Ethernet, CAN, User Priority)
│ ├
Ext. DEPTH (Data1 , Data2, Data4, Ethernet, CAN, User Priority)
│ └
Ext. Wind (Data1 , Data2, Data4, Ethernet, CAN, User Priority)
├ Line Monitor
│ ├ Data1 (Open the line monitor for serial data1.)
│ │ ├ ├ Data2 (Open the line monitor for serial data2.) Data2 (Open the line monitor for serial data2.)
│ ├ Data3 (Open the line monitor for serial datat3.)
│ ├ Data4 (Open the line monitor for serial datat4.)
│ ├ Ethernet (Open the line monitor for Ethernet.)
│ ├ CAN (Open the line monitor for CAN.)
│ ├
GS-1001* (No , Yes)
│ └ LAN Error Counter (Open the LAN error data list.)
│ Number of digits after decimal point
│ │ ├ ├
VTG (1 , 2) VTG (1 , 2)
│ ├
VBW (1, 2 )
│ ├
HDG (1 , 2)
│ └
Roll, Pitch (1 , 2)
└
GNSS Sentence Output* (Enable, Disable )
AP-2 AP-2
Main: Application Main: Application
Main: Boot
GPS: Application
Datum
WMM
LCD (Yes, No ) LCD (Yes No )
Main (Yes, No )
Main (Yes, No )
Rate Gyro(x) (Open the setting window.)
Rate Gyro(y) (Open the setting window.)
Rate Gyro(z) (Open the setting window.)
**: Default (Output Data1 to 3: 4800 bps, Output Data4: 38400 bps)
(HDT Off HRM Off ROT Off THS 0 2 *** VBW 1
*: For serviceman.
) )
t CAN U P i it )
VLW 1