Programming Names - DKS 1802 Installation & Owner's Manual

3.3.6 Programming Names

Before beginning manual programming of this telephone entry system from the keypad, it is strongly recommended that the
resident log sheets in the back of this manual be competed in their entirety. This will make programming easier and can be used
as a reference when entering phone numbers, names and entry codes.
When you are entering names into the electronic directory, remember to press
displayed on the LCD. When the entire name is displayed on the directory, press
directory. If you make a mistake, simply press # to clear the display and start over. Names cannot be more than 11 characters
in length - spaces count as a character. Names are referenced to a phone number by entering the directory code that the
residents phone number has been programmed to.
Example of programming 11 characters: JONES APT 1
Digit Keypad Sequence
JKL JKL
1 J
5 5
MNO MNO
2 O
6 6
MNO MNO
3 N
6 6
DEF DEF
4 E
3 3
PQRS PQRS PQRS PQRS
5 S
7 7
SP SP
6
1 1
ABC ABC
7 A
2 2
PQRS PQRS
8 P
7 7
TUV TUV
9 T
8 8
SP SP
10
1 1
SP SP
11 1
1 1
MNO MNO MNO MNO
1. Press
6 6 6 6
The LCD display will read: DIR CODE.
2. Enter the directory code of the resident (1, 2, 3 or 4 digits, depending on programming in 3.2.1), then press
The LCD display will read: 11 CHAR NAME.
3. Begin entering the residents name one character at a time. (refer to 3.3.1 for reference). When the desired character (letter,
number or space) is displayed, press
4. Repeat step 3 to enter additional characters until the desired name is displayed on the LCD display (11 characters max.).
If you make a mistake, press
5. After the last character has been entered, press
The LCD display will be blank.
6. Repeat steps 2, 3, 4, and 5 to enter additional names.
OPER OPER
7. Press together to end this programming step.
0 0
The LCD display will read: SORTING.
System alphabetizes the names. This may take a few minutes. Sorting is complete when a long (beeeeeep) is heard.
1802-065-D-10-14
Press the 5 key one time to display J, then press the
MNO MNO MNO MNO
Press the 6 key three times to display O, then press the
6 6 6 6
MNO MNO
Press the 6 key twice to display N, then press the
6 6
DEF DEF
Press the 3 key two times to display E, then press the
3 3
PQRS PQRS PQRS PQRS
Press the 7 key four times to display S, then press the
7 7 7 7 7 7
Press the 1 key one time for a space, then press the
Press the 2 key one time to display A, then press the
Press the 7 key one time to display P, then press the
Press the 8 key one time to display T, then press the
Press the 1 key one time for a space, then press the
SP SP
Press the 1 key twice to display 1, then press the
1 1
Press the
and enter your four-digit MASTER CODE
(beep) to enter that character.
to clear the display and start over.
*
Programming Description
key to enter the entire name in the system.
*
? ? ? ? ? ?
(beep) again to enter the complete name.
after each desired letter, number, or space is
again to enter the entire name into the
*
key to enter the letter.
*
key to enter the letter.
*
key to enter the letter.
*
key to enter the letter.
*
key to enter the letter.
*
key to enter the space.
*
key to enter the letter.
*
key to enter the letter.
*
key to enter the letter.
*
key to enter the space.
*
key to enter the number.
*
? ?
(beep).
(beep).
31