Five-Digit Entry Codes Time Zone; Flash Entry Codes" Active For One-Day Only - DKS 1802 Installation & Owner's Manual

3.5.4 Five-Digit Entry Codes Time Zone

This programming sequence sets up ONE time zone for the FIVE-digit entry codes to activate the system relays. This time zone
uses a range of five-digit entry codes (Boundary numbers) and can be programmed for certain days of the week. This time zone
can be turned ON and turned OFF after it is programmed (see operating instructions 4.2.4 to turn ON or OFF the programmed
entry code time zone).
Note: FLASH entry codes can NOT be used with five-digit entry codes.
DEF DEF PQRS PQRS
1. Press
3 3 7 7
SP SP
2. Press (beep) to turn time zone ON, OR
1 1
3. Enter the four-digit BEGINNING hour and minutes, then press
DO NOT use military (24 hour) time format, simply enter the hour (2 digits) and the minutes (2 digits). For example, 8:30 is
entered as 0830. AM or PM gets set on the next step.
OPER OPER
4. Press (beep) for AM, OR
0 0
5. Enter the four-digit ENDING hour and minutes, then press
DO NOT use military (24 hour) time format, simply enter the hour (2 digits) and the minutes (2 digits). For example, 8:30 is
entered as 0830. AM or PM gets set on the next step.
OPER OPER
6. Press (beep) for AM, OR
0 0
7. Enter the seven-digit days of the week, then press
All seven digits MUST be entered, to skip any days of the week the time zone will NOT be active, enter # in place of a day.
Example 1: to have a time zone active on Saturday and Sunday ONLY (Sun = 1, Sat = 7), enter 1 7 # # # # #.
Example 2: to have a time zone active on Monday thru Friday ONLY (Mon = 2, Tues = 3, ......Fri = 6), enter 2 3 4 5 6 # #.
8. Enter the LOWER five-digit entry codes boundary number, then press
Entry codes LOWER than this number will NOT activate relays when the entry code time zone is ON.
9. Enter the UPPER five-digit entry codes boundary number, then press
Entry codes HIGHER than this number will NOT activate relays when the entry code time zone is ON.
OPER OPER
10. Press together to end this programming sequence (beeeeeep).
0 0
3.5.5 "Flash Entry Codes" - Active for ONE-DAY ONLY
This programming sequence sets up "Flash Entry Codes". Flash codes are four-digit entry codes that will operate ONLY ONE
TIME on a specific day of the month - they will not operate before or AFTER the programmed day. The flash codes will be valid
for a single 24-hour period ONLY. For example, if you program a flash code on July 1st to be active on the 10th, the code will
become valid at 00:00 AM on July 10th and expire at 11:59 PM on July 10th. The code will not be valid on August 10th. You can
program up to EIGHT flash codes in the system.
Flash code numbers 1 through 4 will activate Relay 1 ONLY.
Flash code numbers 5 through 8 will activate Relay 2 ONLY.
SP SP
JKL JKL
1. Press
1 1 5 5
2. Enter a single-digit flash code number (1-8 depending on which relay is to be activated), then press
3. Enter the two-digit day of the month that the code is to be active, then press
4. Enter a desired four-digit FLASH ENTRY CODE, then press
6. Repeat steps 2 through 4 to enter additional desired FLASH ENTRY CODES.
OPER OPER
4. Press together to end this programming sequence (beeeeeep).
0 0
1802-065-D-10-14
and enter your four-digit MASTER CODE
SP SP
(beep) for PM.
1 1
SP SP
(beep) for PM.
1 1
and enter your four-digit MASTER CODE
? ? ? ? ? ?
OPER OPER
(beep) to turn time zone OFF.
0 0
(beep).
(beep).
(beeeeeep). (Sun = 1, Mon = 2, .....Sat = 7)
(beep).
(beep).
? ? ? ? ? ?
(beep).
? ?
(beep).
? ?
(beep).
(beep).
(beep).
37