Network Connection; Connection Test - FUNAI BH2-M200 Owner's Manual

Network Connection

[SETUP] A "Settings" A "Others" A "Network Connection"
Set up the network connection settings in order to use BD-
Live™ service or network update function.

Connection Test

After you made IP address / DNS settings or when a LAN
cable is connected, always perform the connection test to
check if the connection is correctly made.
1
Select "Connection Test", then press
[ENTER\OK].
Connection test will start automatically and the test result
will appear right after the connection test finishes.
Testing... : The test is in progress.
Pass : Connection test is successfully completed.
Fail : Connection test failed.
Check the connection settings.
Press [ENTER\OK] to go to the list of network status
confirmation screen.
2
Press [ENTER\OK] to go back to the previous
screen, or press [SETUP] to exit.
Note
• If the connection test passes, you are ready to use
BD-Live™ function using the Internet without making any
extra settings.
• If the connection test fails, you may need to change the MAC
address settings on your router. You can check the MAC
address of this unit on "Network Connection" screen.
• "Connection Test" is not available when "Disable" is selected
in "Network Connection".
Auto
Network settings are set to the following settings initially.
(In most cases, you can connect to the Internet without
making any changes to the default settings.)
- IP Address Setting Auto(DHCP)
- DNS Setting Auto(DHCP)
- Proxy Setting Do Not Use
- Connection Speed Auto
- BD-Live Setting Allow
If you want to set the network settings back to the default
settings as above (except "BD-Live Setting"), follow the
procedure below.
1
Select "Auto", then press [ENTER\OK].
The unit will start the connection test automatically and
the test result will appear right after the test finishes.
Press [ENTER\OK] to go to the list of network status
confirmation screen.
2
Press [ENTER\OK] to activate the network
settings and set the network connection
automatically. Press [SETUP] to exit.
Note
• The setting of "BD-Live Setting" will not be set back to the
default, even if you follow the procedure.
Manual
In following cases, select "Manual" to set each setting as
necessary.
- When connection test failed with the setting of "Auto".
- When instructed by your Internet service provider to make
specific settings in accordance with your network
environment.
IP Address Setting / DNS Setting
1
Select "Manual", then press [ENTER\OK].
2
Select "IP Address Setting", then press
[ENTER\OK].
3
Select the desired setting, then press
[ENTER\OK].
Auto(DHCP) : If your router has DHCP server function,
select "Auto(DHCP)".
Manual : If your router does not have DHCP server
function, select "Manual".
If you select "Manual", follow the following
instruction to set the IP address and DNS.
If you select "Auto(DHCP)", skip to step
3
-a) Select "IP Address", "Subnet Mask" or "Default
Gateway", then press [ENTER\OK]. IP address
setting screen will appear. Enter IP address, subnet
mask and default gateway with
[the Number buttons].
• Enter the IP address number after checking the
specifications of your router.
• If the IP address is unknown, check the IP
address of other devices. (e.g. PC connected via
LAN cable) and assign a different number from
those of other devices.
3
-b) After you enter all correctly, press [ENTER\OK].
• Confirmation message will appear. Select "Yes" to
complete the settings.
3
-c) Select "Primary DNS" or "Secondary DNS", then
press [ENTER\OK]. DNS setting screen will
appear. Enter primary DNS and secondary DNS
with [the Number buttons].
• Enter the DNS addresses provided by your
Internet provider.
• If the DNS address is unknown, check the DNS
address of other devices (e.g. PC connected via
LAN cable) and assign the same DNS address.
3
-d) After you enter all correctly, press [ENTER\OK].
Confirmation message will appear. Select "Yes" to
complete the settings.
4
Press [RETURN\BACK] to go back to the
previous screen, or press [SETUP] to exit.
4
.
69
EN