FUNAI BH2-M200 Owner's Manual page 17

HDMI / COAXIAL Audio Output
To see how the audio is output from the HDMI OUT / COAXIAL (digital audio out) jack, refer to the table below.
"Dolby D/Dolby D+/
Dolby TrueHD", "DTS/
DTS-HD", "MPEG"
settings
"BD Audio Mode"
setting "HD Audio
Output"
Audio Source
Dolby Digital Dolby Digital
Dolby Digital
Dolby Digital Plus
Dolby TrueHD
TrueHD
®
DTS
®
DTS-HD DTS-HD
HE-AAC
MPEG
MP2
(MPEG Audio Layer2)
LPCM
MP3
• To hear the BD-video secondary audio, select "Mix Audio Output".
*1
• For the audio output from the HDMI OUT, the audio format supported by your connected device (such as amplifier /
receiver) will be output. The best available audio format are shown in the table above.
• "HDMI Audio Out" should be set to "On".
• Because HDMI is an evolving technology, it is possible that
some devices with an HDMI input may not operate properly
with this unit.
• The audio signals from the HDMI connector (including the
sampling frequency, the number of channels and bit length)
may be limited by the device that is connected.
• Among the monitors that support HDMI, some do not
support audio output (for example, projectors).
• If the connected device is not compatible with HDMI
BITSTREAM, DTS sound will not be output.
• When the power failure occurs, or when you unplug the unit,
some problems in the HDMI setting might occur.
Please check and set the HDMI setting again.
• HDMI OUT of this unit does not output the multi-channel
audio, such as 5.1ch, recorded on DVDs. To enjoy multi-
channel audio, connect this unit to a decoder through the
COAXIAL (digital audio out) jack.
• Multi-channel audio which is recorded on a TS title or the
one comes along with the DVB programmes can be output
from the HDMI OUT.
• Sound recorded at 96kHz is down sampled to 48kHz.
*1
HDMI OUT
"Bitstream"
"Mix Audio "HD Audio
Output" Output"
Plus Dolby Digital
Dolby
®
DTS
® ®
DTS
Dolby Digital
MPEG
Multi PCM
2ch PCM
"PCM" "Bitstream"
"Mix Audio "HD Audio
Output" Output"
Dolby Digital
Multi LPCM
Dolby Digital
2ch PCM
Note for HDMI Video Resolution
• Video and audio signals may be distorted temporarily when
switching to / from the HDMI output mode.
• You cannot change the video resolution during Blu-ray
Disc™ playback. To change the resolution, stop playback.
• In order to get natural and high quality film reproduction of
24-frame film material, use an HDMI cable (High Speed
HDMI cable is recommended) and select "Auto" if the
connected TV is compatible with 1080p24 frame input.
• Even if the connected TV is compatible with 1080p24 frame
input and you set "HDMI Video Resolution" setting to "Auto",
when the contents of the disc are not compatible for
1080p24 frame, 1080p60 frame will be output.
• If the picture is not output properly to the TV because of
"HDMI Video Resolution" setting, press and hold [PLAY B]
on the front panel for more than 5 seconds. The setting will
be reset to the default automatically.
• With some copy-protected BD-video, the video image may
only be output from HDMI OUT jack.
• Refer also to your TV's manual.
Copyright protection system
To play back the digital video images of a BD-video or DVD-
video via an HDMI connection, it is necessary that both the
player and the display device (or an AV receiver / amplifier)
support a copyright protection system called HDCP (high-
bandwidth digital content protection system). HDCP is copy
protection technology that comprises data encryption and
authentication of the connected AV device. This unit supports
HDCP. Please read the operating instructions of your display
device (or AV receiver / amplifier) for more information.
* HDMI: High-Definition Multimedia Interface
COAXIAL (digital audio out)
"PCM"
"Mix Audio "HD Audio
Output" Output"
DownMix 2ch PCM
®
DTS
MPEG
DownMix 2ch PCM
2ch PCM
"Mix Audio
Output"
17
EN