FUNAI BH2-M200 Owner's Manual page 70

Note
• The range of input numbers is between 0 and 255.
• If you enter a number larger than 255, the number will
automatically be 255.
• The manually entered addresses will be saved even if you
change the setting to "Auto(DHCP)".
• If you want to enter 1 or 2 digit number in one cell, press [B]
to move on to the next cell.
• If the entered IP address or the default gateway or primary
DNS address is same as the default setting, IP address
setting will be set to "Auto(DHCP)". (The manually entered
number will be saved.)
• When IP address setting is set to "Manual", the setting of
DNS setting will automatically be "Manual" and when IP
address setting is set to "Auto(DHCP)", you can set either
"Auto(DHCP)" or "Manual" for DNS setting.
Proxy Setting
1
Select "Manual", then press [ENTER\OK].
2
Select "Proxy Setting", then press [ENTER\OK].
• For default settings, select "Do Not Use".
• If you need to change the proxy setting as instructed by
your Internet service provider to set the designated
proxy address and port, select "Use".
If you select "Use", follow the following instructions
to set the proxy address and proxy port.
2
-a) Select "Proxy Address", then press [ENTER\OK].
The keyboard screen will appear. Enter proxy
address using the [the Number buttons], then
press [ENTER\OK].
[Red] : Upper case letters and symbols
[Green] : Lower case letters and symbols
[Yellow] : Numbers
• To delete letters, press [CLEAR] repeatedly. Press and
hold [CLEAR] to delete all letters.
2
-b) After you enter proxy address correctly, press
[ENTER\OK].
• Confirmation message will appear. Select "Yes" to
complete the settings.
2
-c) Select "Proxy Port", then press [ENTER\OK].
Proxy port setting screen will appear. Enter proxy
port number with number buttons.
2
-d) After you enter proxy port correctly, press
[ENTER\OK].
3
Press [RETURN\BACK] to go back to the
previous screen, or press [SETUP] to exit.
Note
• The range of input numbers for the port number is between
0 and 65535. (If you enter a number larger than 65535, it will
be regarded as 65535.)
• For proxy port, certain ports might be closed, blocked or
unusable depending on your network environment.
70
EN
Connection Speed
You can set connection speed as your preference.
(The default setting is "Auto".)
1
Select "Manual", then press [ENTER\OK].
2
Select "Connection Speed", then press
[ENTER\OK].
3
Select the desired setting, then press
[ENTER\OK].
"Auto":
Set the appropriate connection speed automatically, in
accordance with your network environment.
"10BASE Half":
Set the connection speed to "10BASE Half".
"10BASE Full":
Set the connection speed to "10BASE Full".
"100BASE Half":
Set the connection speed to "100BASE Half".
"100BASE Full":
Set the connection speed to "100BASE Full".
4
Press [RETURN\BACK] to go back to the
previous screen, or press [SETUP] to exit.
Note
• Choose a connection speed in accordance with your
network environment.
• The network connection may be disabled depending on the
device, when the settings are changed.
BD-Live Setting
You can limit Internet access for BD-Live™ discs.
(The default setting is "Allow".)
1
Select "Manual", then press [ENTER\OK].
2
Select "BD-Live Setting", then press
[ENTER\OK].
3
Select the desired setting, then press
[ENTER\OK].
"Allow":
Internet access is permitted for all BD-Live™ contents.
"Limited Allow":
Internet access is permitted only for BD-Live™ contents
which have content owner certificates. Internet access
without the certificates is prohibited.
"Prohibit":
Internet access is prohibited for all BD-Live™ contents.
4
Press [RETURN\BACK] to go back to the
previous screen, or press [SETUP] to exit.
Connection Test
Refer to "Connection Test" on page 69.
Disable
Deactivate all the network connection and settings.
1
Select "Disable", then press [ENTER\OK].
Note
• The network connection can be reactivated by setting the
network connection to "Auto" or "Manual".