Bundled Software Setting After Installation Is Completed - Fujitsu PRIMEQUEST 2000 Series Installation Manual

CHAPTER 4 Installation of Operating System and bundled software
4.3 Procedure to install Windows in SAN/iSCSI storage device

4.3.4 Bundled software setting after installation is completed

Bundled software is set after the completion of operating system installation.
1. OneCommand Manager is installed in the following cases.
- When the Emulex FC card or Converged Network Adapter Card is mounted.
And
- When OneCommandManager is not installed
The installation condition of OneCommandManager is determined by the presence of [Emulex] – [OneCommand
Manager] under the [start] menu – [all programs].
Note
In Windows Server 2012 or Windows Server 2012 R2, "the [start] menu – [all programs]" should read "the [start]
menu – [all apps]".
a. Driver/Utility of FC Card is downloaded from the following URL.
http://support.ts.fujitsu.com/
Note
Driver/ Utility can be used by the PRIMEQUEST 2000 series though PRIMERGY is described in the
downloaded binary.
b. The downloaded file is executed by a double click.
The prompt window of cmd.exe (black window) is displayed for a while and the file is extracted.
c. The window closes automatically after the extraction is completed.
The download file is extracted and folder or file is newly created.
Remark
If the window does not close even if "Complete" is displayed on the title bar of the window then click the "Close"
button and close the window.
d.
Double click and execute "elxocm-windows-x86-XXXXX.exe"(in case of x86, 32-bit OS) or "elxocm-windows-
x64-XXXXX.exe"(in case of x64, 64-bit OS) in "FC_vXXXXXX" directory created by extraction.
Remark
"XXXX" shows the version number. Read properly.
2. Qlogic Converge Console (GUI/CLI) is installed in the following cases.
- When the Qlogic FC card is mounted.
And
- When Qlogic Converge Console (GUI/CLI) is not installed
The installation condition of Qlogic Converge Console (GUI) is determined by the presence of [Qlogic Corporation] –
[QCC GUI (localhost)] under the [start] menu – [all programs]
The installation condition of Qlogic Converge Console (CLI) is determined by the presence of [Qlogic Management
Suite] -[QConvergeConsole CLI] under the [start] menu – [all programs]
Note
In Windows Server 2012 or Windows Server 2012 R2, "the [start] menu – [all programs]" should read "the [start]
menu – [all apps]".
a. Driver/ Utility of FC Card is downloaded from the following URL.
http://support.ts.fujitsu.com/
Note
Driver/Utility can be used by the PRIMEQUEST 2000 series though PRIMERGY is described in the
downloaded binary.
b. The downloaded file is executed by a double click.
The prompt window of cmd.exe (black window) is displayed for a while and the file is extracted.
c. The window closes automatically after the extraction is completed.
The download file is extracted and folder or file is newly created.
Remark
If the window does not close even if "Complete" is displayed on the title bar of the window then click the "Close"
button and close the window.
d.
Double click and execute "QConvergeConsole_Installer_Windows_XXXXX.exe" in "QCC_vXXXXXX" directory
created by extraction.
Remark
"XXXX" shows the version number. Read properly.
3. When the installation is completed, the partition is rebooted.
4. The setting of management LAN is confirmed.
Confirm STP function for switch is turned off if the switch is connected to management LAN for MMB.
5. The trap destination and mail destination are set through MMB.
Execute the coordination with the management software, etc. only if necessary.
a. [SNMP settings] is displayed on the MMB window and enable [SNMP] .
b. The trap destination of SNMP through MMB is set.
"6.5.2 Set up of SNMP"
64
CA92344-0536-01