Com Port Setup - Texecom Premier 640 Installation Manual

Programming the Control Panel
CRC:??? (<=009), Cyclic Redundancy Check
BER:??? (<=009), Bit Error Rate
This screen displays the Cyclic Redundancy Check (CRC)
and Bit Rate Error (BER) of the Radio-Pad that is connected
to the control panel.
!
The CRC and BER values should be less than 10.
Signal =??? dBm (<=080), GSM Signal
GSM BER:??? (<=004), GSM Bit Error Rate
This screen displays the signal strength (GSM) and Bit Rate
Error (BER) of a GSM Module that is connected to the control
panel.
!
The GSM value should be greater than or equal to 80
and the BER value should be less than 9.
Com1 Monitor Screen
This screen allows you to view the data activity of Com1.
Press RESET to reset the device connected to this port.
Com2 Monitor Screen
This screen allows you to view the data activity of Com2.
Press RESET to reset the device connected to this port.

Com Port Setup

>73!:0!3$-$6:Z[
\C?]C595!HO:508<
Yes
\C?]C595!HO:508<
;$<$:!C595
8
tuv
\C?]C595!HO:508<
,0/!I0):!3$:#O
Yes
H8E0()D!C59560/
,0/f%%!'0D#-$
,0/!I0):!+
L0!'0D#-$!25::$D
No
,0/!I0):!+
L0!'0D#-$!25::$l
7
pqrs
,0/!I0):!+
V3'!'0D#-$!!!!!l
Yes
The control panel must be programmed with the type of
device that are connected to each of its coms ports.
Com Port 1 and 2
Available Device Types:
76
Use the SCROLL
key to select the
required Com Port
Press NO to edit
the Com Port
Use keys 0 - 8 to select
an device or use the
SCROLL key to search
e.g. 7 = GSM Module
0: No Module Fitted - No Devices/PC-Com/ USB-Com
1: Com300 - Com300 Communicator.
2: Com2400 - Com2400 Communicator.
3: ComISDN - ComISDN Communicator.
4: ComIP - ComIP TCP/IP Communication Module.
5: Modem Unit - Standard Serial PC Modem.
6: Radio Pad - Paknet RP9 Radio-Pad.
7: GSM Module - GSM Module/Mobile Phone.
8: Crestron System - Crestron Home Automation System.
9: SIP - Serial IP Protocol.
10: RadioPlus - Premier Serial Wireless Receiver.
11: Inovonics Radio - Inovonics Serial Wireless Receiver.
12: WebWayOne - WebWayOne UDP Module.
13: X-10 Control - X-10 Home Automation Module.
14: IRIS IP - Chiron IRIS Serial TCP/IP Module.
Onboard Digicom
This option determines what type of device is connected to
the plug-on digmodem connector on the top right hand
corner of the control panel. (Default = Com300).
Available Device Types:
0 / 1 / 2 / 3
Com1
This option determines what type of device is connected to
the Com1 connector on the left hand side of the control
panel. (Default = No Module Fitted).
Available Device Types:
0 / 2 / 3 / 4 / 5 / 7 / 8 / 9 / 10 / 12 / 13 / 14
!
If any of the above devices are connected to the
control panel on Com1 and a PC needs to be
connected (for uploading/downloading) the device
must be disconnected from Com 1 and the 'Factory
Default' button pressed for 3 seconds to allow the PC
to talk to the control panel.
If the PC is not connected to the control panel (or is
removed) the Com port will automatically revert back to
normal operation after 1 minute.
Com2
This option determines what type of device is connected to
the Com2 connector on the left hand side of the control
panel. (Default = No Module Fitted).
Available Device Types:
0 / 2 / 3 / 4 / 5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14
Expansion Port
This option determines what type of device is connected to the
Expansion Port connector (Default = No Module Fitted).
Available Device Types:
0: No Module Fitted - No Devices
1: AV Module - Premier Audio Verification Module
2: iD Module - Premier 60IXD iD Module
3: X10 Module - X10 Controller
4: Premier OP8 - Premier Output Module (8 Outputs)
Premier 640 Installation Manual
INS344