Premier Elite Ricochet Kits Quick Guide Introduction Texecom has developed a new method of wireless security signalling based on the concept of mesh networking. Mesh-networking is the process whereby every single wireless device is capable of receiving and retransmitting any signal from any other wireless device on the network.
Premier Elite Ricochet Kits Quick Guide System Design & Installation Considerations Before attempting to install the alarm system, read this section. Once you have an overall understanding of the installation sequence, carefully work through each step. This quick reference guide will allow you to install your alarm system and programme all of the required basic functions.
Premier Elite Ricochet Kits Quick Guide 7: Apply Power to the Control Panel Once steps 1 to 5 are completed, apply power to the control panel. 8: Installation Records You should record notes detailing the location of each device installed on the system, and the date of installation.
Keypad Types Texecom provide a number of different styles of keypads. The image below shows the layout of the Premier LCDLP Keypad with iconic keys, a large screen and Proximity tag capability. The table details the equivalent keys of an alternate is supplied.
Premier Elite Ricochet Kits Quick Guide Connecting Keypads & Expanders Before connecting keypads, zone expanders and output modules, isolate ALL power from the control panel (AC Mains & Battery). Do not continue if there is still power present on the control panel.
Premier Elite Ricochet Kits Quick Guide Keypad & Expander Addressing Each keypad or expander must be assigned an address using the DIL switches located on the left hand side of the PCB. The table below shows the addressing: Address DIL 1...
Premier Elite Ricochet Kits Quick Guide Auto Zone Type & Area When learning devices, if no editing has taken place of the control panel onboard hardwired zones, these will be switched to Not Used after the first Ricochet device is learned to the system; the following defaults will be used for Ricochet devices learned to the system.
Premier Elite Ricochet Kits Quick Guide For maximum reliability and system integrity avoid long and thin set-ups. Devices are capable of hopping through up to two other devices, or a maximum of three hops. Learning SmartKeys Once all of the other devices have been mounted in their final location you may learn the SmartKeys to the system. The following procedure should be used:- ...
Premier Elite Ricochet Kits Quick Guide Finishing the Installation Install all of the covers to the devices and the external sounder if fitted. and the proceed as follows:- Remove the jumper link from Commission jumper on the panel PCB. Fit the panel lid Now test the system.
Page 12
Premier Elite Ricochet Kits Quick Guide (only applicable for B = Bell/Strobe C = Enable Coms custom zone types) I =Internals W = Warning M = Monitor 24Hr Zone Areas - ...
Premier Elite Ricochet Kits Quick Guide Area Programming Remote Disarm Log Part Omits Panel Tamper Multi Knock Area Bell Tamper UDL Keypad Auxiliary Tamper Auto Chime (C2A) Panel Speaker Confirm in Entry Bell & Strobe op Conf. After Entry...
Page 14
Premier Elite Ricochet Kits Quick Guide Global Options Chime Volume Adjust Clock Country Code & Defaults Number Of Re-Arms Quick Count Anti-code Resets Modem Level Monitor Press to edit, to select an option, to change the option,...
Page 15
Premier Elite Ricochet Kits Quick Guide Expander Setup Remote Reset PSU Monitor Line Fault +ve Defer Auto Arming Line Fault -ve Volume - Press to edit, to enter a value,...
Page 16
Premier Elite Ricochet Kits Quick Guide PA Audible Arm Fail Time Arming Detector Mask PA Silent Bell SAB Code Entered Fault Present Duress Bell SCB Code Entered LED Control Fire Alarm Strobe Area Secured Full Armed Entry Medical Switch 12 Volts...
Page 17
Premier Elite Ricochet Kits Quick Guide UDL/Digi Options O = Omits & Reinstates R = Restores Config. - Press to edit, to select option, to accept (only available for Contact ID, SIA Level II, EasyCom Pager &...
Page 18
Premier Elite Ricochet Kits Quick Guide UDL/Digi Options Pad NUA View only Forward Signal View only Reverse Signal View only Bit Error Rate View only Cyclic Redundancy View only GSM Signal/BER View only Com1,2,3 Press to reset com port Com Port Setup ...
Page 19
Premier Elite Ricochet Kits Quick Guide Engineer Utils View System Log to view System, Alarm or Mandatory log System log Use to move up and down through log (down moves back in time, up moves forward again),...
Premier Elite Ricochet Kits Quick Guide Ricochet ® Learn * Will go to the next available wireless zone starting at 9 or Press to search. Learning always starts from the next available zone, deleting ways starts from the highest zone learnt to the system.
Premier Elite Ricochet Kits Quick Guide Changing the Time & Date Time Date Enter the User Code Enter the User Code Press Press Press Press Press Press Press Press Enter the new time Enter the new time ...
Premier Elite Ricochet Kits Quick Guide Premier Elite™ Control Panel Layout ( 48-W Shown) PCB Layout (48-W Shown) BAR CODE Tamper Disable 100 V m = 1 Amp 0.75A 0.3A Batt Charge OPTIONS Engineer REM USE WITH TEXECOM PSU ONLY...
Page 23
Premier Elite Ricochet Kits Quick Guide 28: Cover Tamper Disable Disables the lid tamper Loading the factory defaults can take up to 60 seconds to complete. 29: Flash Programming Port Loading defaults will only be possible if the NVM has not been For upgrading the panel firmware.
Page 24
Texecom Limited, Bradwood Court, St. Crispin Way, Haslingden, Lancashire BB4 4PW, England. Technical Support: UK Customers Tel: 08456 300 600 (Calls charged at local rate from a BT landline. Calls from other networks may vary.) International Customers Tel: +44 1706 233875 Email: techsupport@texe.com...