Oce OP30C Operation Manual
  1. Manuals
  2. Brands
  3. Oce Manuals
  4. All in One Printer
  5. OP30C
  6. Operation manual
Oce OP30C Operation Manual

Oce OP30C Operation Manual

Printing system functions
Hide thumbs Also See for OP30C:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operating Manual
Océ Operations Guide
Education Services
1.1.1.
English version
Océ OP30C
Printing System Functions
Operations Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the OP30C and is the answer not in the manual?

Questions and answers

Related Manuals for Oce OP30C

Summary of Contents for Oce OP30C

  • Page 1 Océ Operations Guide Education Services 1.1.1. English version Océ OP30C Printing System Functions Operations Guide...

  • Page 2: Operation Guide

    Operation Guide Introduction Printer-related operation 1. Features of this Printer 2. Printer Settings 3. Paper size setting for manual feed (for printer use) 4. e-MPS Functions 5. Hard Disk/ RAM Disk 6. Memory Card 7. Printer Control Commands 8. Troubleshooting Software-related operation 9.

  • Page 3: About This Operation Guide

    Introduction About this Operation Guide This Operation Guide is included with your Printing System (P) and should be read in combination with the Operation Guide <Set-Up Edition> for that product. This Operation Guide contains information on making settings in your printer, as well as on installing and setting the printing proper- ties for the corresponding Printer Drivers.
  • Page 4 IBM PROGRAM LICENSE AGREEMENT THE DEVICE YOU HAVE PURCHASED CONTAINS ONE OR MORE SOFTWARE PROGRAMS (“PROGRAMS”) WHICH BELONG TO INTERNATIONAL BUSINESS MACHINES CORPORATION (“IBM”). THIS DOCUMENT DEFINES THE TERMS AND CONDITIONS UNDER WHICH THE SOFTWARE IS BEING LICENSED TO YOU BY IBM. IF YOU DO NOT AGREE WITH THE TERMS AND CONDITIONS OF THIS LICENSE, THEN WITHIN 14 DAYS AFTER YOUR ACQUISITION OF THE DEVICE YOU MAY RETURN THE DEVICE FOR A FULL REFUND.
  • Page 5 Typeface Trademark Acknowledgement All resident fonts in this printer are licensed from Agfa Corporation. Helvetica, Palatino and Times are registered trademarks of Linotype-Hell AG. ITC Avant Garde Gothic, ITC Bookman, ITC ZapfChancery and ITC Zapf Dingbats are registered trademarks of International Typeface Corporation.

  • Page 6: Features Of The Printer

    1. Features of the Printer 1. Printer Settings (15 ppm copier) This printer comes equipped with the following features. KIR (Kyocera Image Refinement) A smoothing function exclusive to Kyocera. This function uses software to increase the resolution of the printer and ensure high-quality printing. The factory default setting for this function is “ON”.

  • Page 7: Printer Settings

    2. Printer Settings 2. Printer Settings 2-1 Procedure for making settings Press the Printer key. The machine will switch to the printer mode. Inch specification Metric specification Use the “M” and “N” cursor keys to select “MENU” and then press the Enter key. Inch specification Metric specification Inch specification...
  • Page 8 2. Printer Settings Operation keys <Inch version> <Metric version>...
  • Page 9 2. Printer Settings 2-2 Menu flow chart MENU Printer Status Page print out ........................e-MPS functions Quick Copy Job print out ....................Private Print / Stored Job print out ..................Virtual Mailbox data print out ..................... Virtual Mailbox List print out ....................

  • Page 10: Table Of Contents

    2. Printer Settings Emulation protocol ........................... PCL 5c Code set selection ..................KC-GL Pen (1 - 8) settings ..................Pen thickness ............... Pen color ................Page set ...................... KPDL KPDL Error Report print out ON/OFF ............KPDL(AUTO) Auto emulation switching ................
  • Page 11 2. Printer Settings Hard Disk settings Reading data ........................Reading program data ....................... Writing data ........................Deleting data ........................Deleting font data ......................Deleting program data ....................... Deleting macro data ......................Formatting Hard Disk ......................Partition List print out ......................RAM disk ON/OFF ...........................
  • Page 12 2. Printer Settings Paper handling settings Bypass mode ........................Bypass paper type ......................Paper source selection ...................... Duplex mode ........................Eject location selection ...................... A4 & Letter usage ON/OFF ....................Custom paper type Custom type (1 - 8) ..................Paper thickness ..............
  • Page 13 2. Printer Settings 2-3 List of settings Item No. Item Display message Available settings Remarks Printer Status Page print out Print Status Page No, Print Prints out a list of such items as printer default settings and memory volume, etc. Quick Copy Job print out Quick Copy Displayed only when the optional...
  • Page 14 2. Printer Settings Item No. Item Display message Available settings Remarks Interface selection Interface Parallel, Serial, “Option 1” is displayed only when Displays the interface that is currently Option 1 the Network Card is installed. selected. The arrow (>) will indicate the currently selected interface.
  • Page 15 2. Printer Settings Item No. Item Display message Available settings Remarks NetWare ON/OFF NetWare On, Off NetWare frame type NetWare Frame Auto, 802.3, Displayed only when the NetWare Sets the NetWare frame type. Ethernet II, 802.2, setting is turned “On”. 802.3 SNAP TCP/IP ON/OFF TCP/IP...

  • Page 16: Emulation Protocol

    2. Printer Settings Item No. Item Display message Available settings Remarks Emulation protocol Emulation PCL 5c, KC-GL, Allows you to set a different Sets the emulation protocol that will be used. KPDL, KPDL emulation protocol for each (AUTO) interface. Select the desired interface under the “Interface selection”...

  • Page 17: Font Selection

    2. Printer Settings Item No. Item Display message Available settings Remarks Font selection Font ID To select an installed font, select Selects the font that will be used for printing. the “Internal” menu. To select a font This setting is made by entering the ID of the other than those already installed, desired font.

  • Page 18: Smoothing On/Off

    2. Printer Settings Item No. Item Display message Available settings Remarks Smoothing ON/OFF KIR Mode On, Off For black and white print out only. Allows you to have the jaggies that appear around the edge of text or graphics to be evened out through a smoothing process.

  • Page 19: Deleting Program Data

    2. Printer Settings Item No. Item Display message Available settings Remarks Deleting font data Delete Font Select the name of Displayed only when there is Deletes the selected font data from the Hard the font from among appropriate font data on the Hard disk.

  • Page 20: Memory Card Settings

    2. Printer Settings Item No. Item Display message Available settings Remarks Deleting data Delete Data Select the name of Displayed only when there is Deletes the selected data from the RAM the partition which appropriate data in the RAM disk. disk.

  • Page 21: Formatting The Memory Card

    2. Printer Settings Item No. Item Display message Available settings Remarks Deleting font data Delete Font Select the name of Displayed only when there is Deletes the selected font data from the the font from among appropriate font data in the Memory Card.

  • Page 22: Custom Paper Type

    2. Printer Settings Item No. Item Display message Available settings Remarks Custom type (1 - 8) Select Paper Type Custom 1- 8 Sets the paper thickness, fuser temperature (TYPE ADJUST) control and duplex print out for the custom types 1 - 8 selected under the “Bypass paper type”...

  • Page 23: Form Feed Time-Out

    2. Printer Settings Item No. Item Display message Available settings Remarks Form feed time-out Form Feed Time out 000 - 495 (sec.) If “000” seconds is selected here, successive pages will not be printed until they are manually force-printed (by selecting the “GO” command in the printer mode and then pressing the Enter key).

  • Page 24: Service Rep Status Page Print Out

    2. Printer Settings Item No. Item Display message Available settings Remarks Service Rep Status Page print out Print Status page No, Print Prints out a Status Page for use by your service representative. Color test page 1 print out Print Test Page 1 No, Print A test print for black, yellow, magenta and cyan is carried out, in that order, starting...
  • Page 25 2. Printer Settings 2-4 Network (TCP/IP) settings When this machine is to be used as a network printer, it is necessary to set the corresponding IP address for the printer. Notes • The IP address that should be registered here will differ depending upon your network environment. Check with your network administrator BEFORE performing this setting.
  • Page 26 2. Printer Settings Use the “M” and “N” cursor keys to select “TCP/IP” and then press the Enter key. Inch specification Metric specification Use the “M” and “N” cursor keys to select “On” and then press the Enter key. Inch specification Metric specification Use the “M”...
  • Page 27 2. Printer Settings Use the “M” and “N” cursor keys to select “Off” and then press the Enter key. Inch specification Metric specification Inch specification Use the “M” and “N” cursor keys to select “IP Address” and then press the Enter key. Metric specification The numeric keys will be used to enter the IP address: Inch specification...
  • Page 28 2. Printer Settings Continue the same procedure for the other 2 blocks and, once the IP address has Inch specification been entered, press the Enter key. Metric specification Use the “M” and “N” cursor keys to select “Subnet Mask” and then press the Enter Inch specification key.
  • Page 29 2. Printer Settings Repeat steps 11 - 13 in order to enter the Gateway address using the same proce- Inch specification dure that you did for entering the IP address. Metric specification Once you are finished making all of the network settings, press the Copier key. The machine will switch back to the copier mode.
  • Page 30 3. Paper size setting for manual feed (for printer use) 3. Paper size setting for manual feed (for printer use) When printing onto envelopes, postcards and the like, you will need to set them manually. Perform the following procedure in order to make the appropriate setting for manual paper feed.
  • Page 31 4. e-MPS Functions 4. e-MPS Functions 4-1 About the e-MPS Functions If the optional Hard Disk is installed, you will be able to use the e-MPS functions. These functions include the following. Quick Copy After printing is completed, if you need to print out another copy of the same job, additional print out can be instructed from the printer's operation panel without the need to start the printing procedure from your computer again.
  • Page 32 4. e-MPS Functions 4-2 Quick Copy This mode allows you to make additional printouts of a document that was already printed out once. If printing is carried out while Quick Copy is selected in the printer driver, the data for the document being printed out will also be stored onto the printer's Hard Disk.
  • Page 33 4. e-MPS Functions Use the “M” and “N” cursor keys to select “Quick Copy” and then press the Enter Inch specification key. Metric specification Use the “M” and “N” cursor keys to select your user name and then press the Inch specification Enter key.
  • Page 34 4. e-MPS Functions 4-2-2 Deleting documents stored for Quick Copy Inch specification Follow steps 1 through 6 of the previous procedure and select the document data that you want to delete. Metric specification Use the “M” and “N” cursor keys to select “Delete” and then press the Enter key. Inch specification The selected document data will be deleted.
  • Page 35 4. e-MPS Functions 4-4 Private Print / Stored Job Printing The Private Print function aims at protecting the confidentiality of the documents to be printed. Print out is accomplished by entering into the operation panel a 4-digit access code that was previously registered in the printer driver. After print out, the document data will be erased from the printer's memory.
  • Page 36 4. e-MPS Functions Use the “M” and “N” cursor keys to select “Private/Stored” and then press the Inch specification Enter key. Metric specification Use the “M” and “N” cursor keys to select your user name and then press the Inch specification Enter key.
  • Page 37 4. e-MPS Functions Inch specification Use the numeric keys to enter the desired number of copies and then press the Enter key. Printing will start. Metric specification 4-4-2 Deleting stored documents Inch specification Follow steps 1 – 6 of the previous procedure and select the document data that you want to delete.
  • Page 38 4. e-MPS Functions 4-5 Virtual Mailbox (VMB) The Virtual Mailboxes allow you to make use of mailbox functions using the printer aloe. After a Virtual Mailbox has been specified as the output location in the printer driver, the transmitted data will be stored on the printer's Hard Disk. A maximum of 255 Virtual Mailboxes can be created and there is no limit to the number of pages that can be stored in each mailbox.
  • Page 39 4. e-MPS Functions Use the “M” and “N” cursor keys to select “Print Virtual MailBox Data (PRINT VMB Inch specification DATA)” and then press the Enter key. Metric specification Use the “M” and “N” cursor keys to select the Virtual Mailbox whose contents you Inch specification want to print out and then press the Enter key.
  • Page 40 5. Hard Disk/ RAM Disk 5. Hard Disk/ RAM Disk 5-1 About the Hard Disk The optional Hard Disk can be installed in your printer. By installing the Hard Disk in your printer, you will be able to use the e-MPS functions (Quick Copy, Proof and Hold, Private Print, Stored Job Printing (Job Storage), Virtual Mailbox (VMB), Temporary/Permanent Code and Electronic Sorting).
  • Page 41 6. Memory Card 6. Memory Card This machine comes equipped with a slot for inserting a Memory Card. Use a Memory Card that contains fonts in order to print with fonts other than those already installed in the machine, or use the card to save and then read print data.
  • Page 42 6. Memory Card Use the “M” and “N” cursor keys to select “MENU” and then press the Enter key. Inch specification Metric specification Inch specification Use the “M” and “N” cursor keys to select “Memory Card” and then press the Enter key.
  • Page 43 7. Printer control commands 7. Printer control commands It is possible to issue simple commands to the Memory Card and RAM Disk from the MS-DOS Prompt in Windows. 7-1 Using printer control commands A printer control command line includes “!R!” (Command operation start), as well the actual commands and parameters that are to be implemented and that are entered after that.
  • Page 44 7. Printer control commands 7-3 Writing print data Perform the following procedure when you want to print data to a Memory Card, Hard Disk or RAM disk from your computer. * Print data commands can be entered from the operation panel on the copier itself. Refer to “2. Printer settings” on page 2-1 for information on the appropriate procedure.
  • Page 45 7. Printer control commands 7-5 Reading print data Perform the following procedure when you want to read print data that has been saved on a Memory Card or RAM Disk. * Perform the following procedure when you want to read print data that has been saved on a Memory Card, the Hard Disk or RAM disk. * Verify beforehand that the Memory Card is in a write-enabled state and that the RAM Disk is turned ON.
  • Page 46 7. Printer control commands 7-7 Printing out the Partition List Perform the following procedure when you want to print out the Partition List in order to verify the print data and font data that has been saved on a Memory Card, the Hard Disk or RAM disk. * Partition List print out can be accomplished from the operation panel on the printer itself.

  • Page 47: Troubleshooting

    8. Troubleshooting 8. Printer Settings 8-1 Canceling printing Perform the following procedure when you want to stop printing or you want to clear data. IMPORTANT! • Always cancel the print job at your computer first. If the print job is not canceled in your computer, the data will be sent once again to the printer.

  • Page 48: When An Error Message Appears

    8. Printer Settings 8-2 When an error message appears… If an error message appears on the operation panel, first check the following tables for cause of the trouble and then perform the corresponding procedure. For more detailed information, refer to the Operation Guide for your copier as well as the Operation Guide for any optional equipment that is installed in your machine.
  • Page 49 8. Printer Settings Display message Procedure RAM disk error Press GO Code:## Check the error code displayed in place of ## and refer to the following. RAM DISK ERROR PRESS GO 01: Format error. Turn power OFF and ON again. 02: The RAM disk mode is OFF.
  • Page 50 8. Printer Settings Display message Procedure Hard Disk error Press GO Code:## Check the error code displayed in place of ## and refer to the following. HARD DISK ERROR PRESS GO 01: Format error. Reformat the hard disk. 02: Hard disk load error. Correctly load the hard disk. 03: A write error has occurred.
  • Page 51 8. Printer Settings Display message Procedure Warning low memory There is not enough memory. You can check how much printer memory there is by printing out a status page. Delete any unnecessary font data and macros. WARNING LOW MEMORY Warning image adapt Because there is not enough memory, printing cannot be performed at the set resolution.
  • Page 52 9. Procedure for Installing and Printing with a Printer Driver 9-1 Included printer drivers The following printer drivers are included with this product. * Each type of printer driver has a version appropriate to a specific model of copy machine. Be sure to choose the driver that is appropriate for your copier.
  • Page 53 9. Procedure for Installing and Printing with a Printer Driver 9-2 System requirements Windows 95/98 Recommended environment Pentium 90 MHz or faster 16 MB or more 10 MB or more CD-ROM drive 1 drive Windows NT 4.0 Recommended environment Pentium 90 MHz or faster 32 MB or more 10 MB or more CD-ROM drive...
  • Page 54 9. Procedure for Installing and Printing with a Printer Driver 9-3 Screen that Appears when the CD-ROM is Inserted This section explains the screen that appears when the CD-ROM supplied with the Printing System is inserted into the CD-ROM drive. Install Drivers Click to start installation of the printer driver.
  • Page 55 9. Procedure for Installing and Printing with a Printer Driver 9-4 Installing the Printer Driver (Windows) Install the printer driver as follows: * The printer can be connected to the computer by one of the following two methods: local or network. If you want to connect them through network, refer to the operation manual of the operating system (OS).
  • Page 56 9. Procedure for Installing and Printing with a Printer Driver Select the driver type. From the list, select the type of driver to be installed, then click “Next”. All available options will be displayed. Select the items that you want to install and then click on the “Next”...
  • Page 57 9. Procedure for Installing and Printing with a Printer Driver A name can be assigned to your printer. Specify a new name or select the desired name from the list, then click “Next. Specify whether this printer is to be used as the default printer. Click “Yes”...
  • Page 58 9. Procedure for Installing and Printing with a Printer Driver 9-5 Uninstalling the Printer Driver This section explains how to uninstall the printer driver. Use of the uninstaller supplied with the printer driver allows you not only to uninstall the printer driver, but also uninstall the printer driver related files and Windows registries.
  • Page 59 9. Procedure for Installing and Printing with a Printer Driver 9-6 Printing The following is an example procedure for printing using a printer driver under the conditions and environment noted below. • OS: Windows 98 • Printer driver: KX Driver •...
  • Page 60 9. Procedure for Installing and Printing with a Printer Driver Printing from the application Use the application that you want to use to open the document that you want to print. Select “Print” in the “File” menu. The “Print” dialogue box will appear. Select the desired number of copies that you want to make and which pages are to be printed.
  • Page 61 10. Windows KX Driver The following section explains the functions of the KX driver. * The following procedure is explained as though it is being carried out in Windows 98. If you are using another operating system, use this procedure simply as reference. * Depending upon version upgrades of the printer driver, the screenshots shown here may differ somewhat from that of the actual printer driver.
  • Page 62 10. Windows KX Driver 10-2 Media Tab Paper Size: Allows you to select a standard size of paper or an envelope size. The following sizes of paper or envelope can be used with this printer. Standard-size paper sheet Letter (8 1/2" x 11"), Legal (8 1/2" x 14"), Ledger (11" x 17"), 12" x 18", Statement (5 1/2" x 8 1/ 2"), Executive (7 1/2"...
  • Page 63 10. Windows KX Driver 10-2-1 Custom Paper Size dialog box Setting a custom paper size Perform the following procedure in order to register a custom size when you want to print onto a non-standard size of paper. The information registered here will be displayed under the “Page Size” setting in the Media Tab as well as in the Paper Size setting of your application.
  • Page 64 10. Windows KX Driver 10-3 Layout Tab Pages per Sheet: Allows you to print reduced images of multiple (1, 2, 4, 6, 9, 16 or 25) pages onto a single sheet of paper. This function is called “N-Up” printing (where “N” equals the number of image pages). Reduction of the images is calculated automatically so that all of the selected pages fit onto the single sheet of paper.
  • Page 65 10. Windows KX Driver 10-4 Color Tab Color Mode: Selection is possible from among “Color (CMYK)”, “Monochrome” and “Custom…”. If “Custom…” is selected, “Gray Component Replacement”, “Continuous Tone” (for photos, etc.), “Gloss Mode”, “Monochrome” and other settings can be made. Color Correction: Designates the color matching process.
  • Page 66 10. Windows KX Driver 10-4-1 Color Adjustment Select either “HSL (Hue, Saturation, and Lightness)” or “RGB” under “Color Space”. The adjustment screen will change according to the color space selected. The effect of any adjustments can be confirmed in the simulation window on the left side of the dialog box. <When you select “HSL (Hue, Saturation, and Lightness)”…>...
  • Page 67 10. Windows KX Driver 10-5 Prologue/Epilogue Tab Disable Feature Make sure there is NO check mark in this checkbox if you want to use the printer’s overlay function. The overlay function will allow you to have selected macro data printed out on top of your documents. Click on this button when you want to add the data of the file that is selected in the displayed list.
  • Page 68 10. Windows KX Driver 10-6 Imaging Tab Print Quality Selects the quality at which printing will be accomplished. [High Quality] ........Enables printing at the highest quality possible for the printer being used. [Custom...] ..........When carrying out black and white printing, selection is possible between “Kyocera Image Refinement”...
  • Page 69 10. Windows KX Driver 10-7 Output Tab Output to: Specifies the location of ejection of printed copies. Selection is possible when the optional output devices are installed. [Printer Default] ........Copies will be ejected into the location that is selected in the printer as the place where the printed paper will be ejected.
  • Page 70 10. Windows KX Driver Staple Stapling is possible if the optional finisher is installed. * The following settings are required before stapling is possible: (1) “Device Options” setting in the “Device Settings” Tab • Select “RAM Disk” or “Hard Disk”. •...
  • Page 71 10. Windows KX Driver 10-7-1 Printing with the e-MPS (Job Storage) function The e-MPS function is a new feature that combines the functions of job storing, virtual mailboxes and printing from barcodes. With it, you can make multiple copies by sending the print data from your PC once. The data is stored on the printer’s hard disk and used to make subsequent copies.
  • Page 72 10. Windows KX Driver Place a check in the checkboxes of functions you want to use. Temporary ..... Data to be printed is stored on the hard disk of the printer. This can increase the speed of printing for those jobs which involve multiple copy sets.
  • Page 73 10. Windows KX Driver Select “Application Defined” or “Custom” under “Job Name”. If you selected “Custom”, input a user name. This name will be displayed on the touch panel when printing from the printer operation panel. Click on the “OK” button. Printing using the selected function will now be possible. How to print using the Virtual Mailbox function Documents can be stored in virtual mailboxes on the printer’s hard disk and printed out from the printer’s operation panel whenever needed.
  • Page 74 10. Windows KX Driver Selecting a virtual mailbox Place a check in the “Job Storage (e-MPS)” checkbox in the “Job Settings” dialog box and select “Virtual Mail Box (VMB)”. Click on the “Selection” button. The “Virtual Mailbox Selection” dialog box will appear.
  • Page 75 10. Windows KX Driver How to perform barcode printing * The optional Barcode Reader must be installed in order to perform barcode printing. Click in the “Job Storage (e-MPS)” checkbox in the “Job Settings” dialog box and select either “Permanent” or “Temporary”. Once you have selected “Permanent” or “Temporary”, the “Options...”...
  • Page 76 10. Windows KX Driver 10-8 Device Settings Tab Device Options If any optional devices are installed, put a check mark in the checkbox for that device and perform the corresponding settings here. Once you have completed the setting for each option, the functions of that option will be available for use. Paper Feeder (Cassette 3 and 4) Perform this setting according to the installed Option Cassette.
  • Page 77 10. Windows KX Driver “Device Options” list. User… Click on this button when you want to register a user and/or department name. The “User Settings” dialog box will appear. It is also possible to select the “GDI compatible mode” from that dialog box. Refer to “10-8-1 User Settings” on page 10-18 for more detailed information. Administrator…...
  • Page 78 10. Windows KX Driver 10-8-1 User Settings Identification Register the desired user and/or department name. Page Description Language The emulation modes that can be used with this product will be displayed in the dropdown list. If multiple modes are displayed, it is possible to select the desired mode.
  • Page 79 10. Windows KX Driver Registering management codes Click on the “Edit list” button. The “Code list” dialog box will appear. Click on the “Add” button. The “Add Code” dialog box will appear. Type in the desired information in the “Code” and “Description” fields and then click on the “OK”...
  • Page 80 11. Printer Driver for Macintosh 11. Printer Driver for Macintosh When using unit as a network printer, it is possible to print PostScript files from a Macintosh Computer. This section contains explanations regarding the procedure to install the Macintosh PPD files and select this printer, as well as explanation about the computer environment required to run the installed files.
  • Page 81 11. Printer Driver for Macintosh Double-Click on the icon for the CD-ROM disk. The content of the CD-ROM will be displayed. The installer by country and by language is supplied in “Driver” folder. Double-Click the available driver installer to start. The installation screen will appear.
  • Page 82 11. Printer Driver for Macintosh ˙Access the Apple Menu at the far left of the Menu of Bar and select Chooser. The Chooser will appear. Click once on the LaserWriter 8 icon. Select the name of this printer in the “Select a PostScript Printer” list and then click on the “Create”...
  • Page 83 11. Printer Driver for Macintosh 11-3 General Dialog Box *The actual layout of each dialog box and the available option and settings may differ somewhat depending upon the application and version of LaserWriter that you are using. Printer: Selects the desktop printer to be used for printing your document. Copies: Type the desired number of prints to be made (or the number of files to be saved to disk) directly into this field.
  • Page 84 11. Printer Driver for Macintosh 11-4 Layout Dialog Box Pages per sheet: Sets the number of pages to be printed on each sheet of paper. Layout Direction: A button of either is clicked, and a layout direction is decided. If right button is selected, the pages are laid out from right to left. Border: Sets the type of line to appear around the page.
  • Page 85 11. Printer Driver for Macintosh 11-5 Printer Specific Options Resolution: The resolution setting can not be changed from “600 dpi”. Eco Print: Saves on toner. The factory default setting is “Off”. Edge Smoothing: Turning this setting “On” allows the jaggies that appear around the edge of text and graphics to be evened out through the smoothing process.
  • Page 86 11. Printer Driver for Macintosh Paper Destination: Specifies the location of ejection for print jobs. [Inner Tray] ......... Copies will be ejected onto the Inner tray. [Side Tray] ........Copies will be ejected into the side tray. [Finisher (Face-Up)] ....Copies will be ejected into the upper tray of the optional Finisher. [Finisher (Face-Down)] .....
  • Page 87 11. Printer Driver for Macintosh Color Mode: Designates whether printing will be carried out in black and white or in color. Selection is possible between “Color” and “Monochrome”. Ink Simulation (CMYK): Designates the type of ink. Selection is possible from among “SWOP Press”, “Euroscale Press” and “None”. The “Ink Simulation” setting is only valid when “KPDL”...
  • Page 88 11. Printer Driver for Macintosh 11-6 Page Setup dialog Dialog Box Settings for paper size, page layout, magnification ratio and print direction (orientation) are performed in the Page Setup dialog box. To display the Page Setup dialog box, select Page Setup… in the File menu of the corresponding application. * The actual layout of each dialog box and the available options and settings may differ somewhat depending upon the application and the version of LaserWriter that you are using.
  • Page 89 11. Printer Driver for Macintosh 11-7 PostScript Dialog Box The actual layout of each dialog box and the available options and settings may differ somewhat depending upon the application and the version of LaserWriter that you are using. Visual Effects: Visual effects such as horizontal and vertical flip and image inverting can be selected here.
  • Page 90 11. Printer Driver for Macintosh 11-8 Custom paper sizes Dialog Box When a paper sizes is selected in “Custom paper sizes” Dialog Box , the paper size can be set as desired. * The actual layout of each dialog box and the available options and settings may differ somewhat depending upon the application and the version of LaserWriter that you are using.

Table of Contents