System Menu [3] (Midi/Sync) - Roland JUNO-Gi Owner's Manual

Parameter Value
Continuous
OFF, ON
Hold
[3] (CTRL)
Parameter Value
Selects the MIDI message used as the System Control.
OFF
Sys Ctrl 1–4
CC01–31, 33–95
Source
PITCH BEND
AFTERTOUCH
SYSTEM
Source Select
LIVE SET

System Menu [3] (MIDI/SYNC)

[1] (GENERL)
Parameter Value Explanation
Determines whether the internal sound generator
is disconnected (OFF) from the controller section
(keyboard, pitch bend/modulation lever, knobs,
buttons, D Beam controller, pedal, and so on); or not
Local Switch OFF, ON
disconnected (ON).
Normally this is left "ON, " but if you wish to use the
JUNO-Gi's keyboard and controllers to control only
external sound modules, set it to "OFF. "
When you want to transmit or receive System
Device ID 17–32 Exclusive messages, set this parameter to match the
Device ID number of the other MIDI device.
Set this parameter "ON" when you want to use an
external MIDI keyboard instead of the JUNO-Gi's
keyboard. In this case, the MIDI transmit channel
of the external MIDI keyboard can be set to any
Remote
channel. Normally you will leave this parameter
Keyboard
OFF, ON
"OFF. "
Switch
* Turn this "ON" when you want to control the
MIDI receive channel for playing the JUNO-Gi from
Main Channel 1–16
an external MIDI device.
MIDI receive channel on which an external MIDI
Sub Channel 1–16 device can play the JUNO-Gi's Lower layer when the
[SPLIT] button is on.
USB MIDI
If this is "ON, " incoming MIDI messages will be
USB-MIDI
OFF, ON re-transmitted without change from the MIDI OUT
Thru
connector.
82
Explanation
Determines whether the HOLD PEDAL jack
will provide support for half-pedaling (ON),
or not (OFF). When this is set to support
use of half-pedaling techniques, you can
then connect an optional expression pedal
(DP-10, etc.), and employ pedal work to
achieve even finer control in performances
in which piano tones are used.
Explanation
The system control knob will not be used.
Controller numbers 1–95
Pitch Bend
Aftertouch
"Sys Ctrl 1–4 Source" settings will be used
for tone control.
"Tone Ctrl 1–4 Source" (p. 38) settings of each
Live Set will be used for tone control.
JUNO-Gi from an external MIDI device when
performing with the Arpeggio function.
Using the Local Switch
When you're using the JUNO-Gi with external sequencer software, leave the
Local Switch turned off. Read the following for details.
Typically, things are hooked up so the data travels as follows: the JUNO-Gi's
keyboard g your external sequencer software g the JUNO-Gi's sound
generator. Normally, the JUNO-Gi's keyboard section is internally connected to
its sound generator section; this internal connection is controlled by the Local
Switch. If you turn the Local Switch off, the JUNO-Gi's keyboard and sound
generator sections will be independent, allowing you to use the connection
described with your external sequencer software.
Connecting the JUNO-Gi to an external sequencer
JUNO-Gi Keyboard
(External) Sequencer
[2] (TX)
Parameter Value
Transmit
OFF, ON
Program Change
Transmit Bank
OFF, ON
Select
Transmit Active
OFF, ON
Sensing
Transmit Edit
OFF, ON
Data
Soft Through OFF, ON
[3] (RX)
Parameter Value
Receive Program
OFF, ON
Change
Receive Bank
OFF, ON
Select
Receive Exclusive OFF, ON
Receive GM
OFF, ON
System On
Receive GM2
OFF, ON
System On
Receive GS Reset
OFF, ON
Local Off
JUNO-Gi
Sound Generator
Explanation
Specifies whether Program Change messages
will be transmitted (ON) or not (OFF).
Specifies whether Bank Select messages will
be transmitted (ON) or not (OFF).
Specifies whether Active Sensing messages
will be transmitted (ON) or not (OFF).
Specify whether changes you make in the
settings of a patch, performance will be
transmitted as system exclusive messages
(ON), or will not be transmitted (OFF).
Thru function re-transmits all messages
received at the MIDI IN connector to the MIDI
OUT connector without modifying them in
any way.
Explanation
Specifies whether Program Change messages
will be received (ON) or not (OFF).
Specifies whether Bank Select messages will
be received (ON) or not (OFF).
Specifies whether System Exclusive messages
will be received (ON) or not (OFF).
Specifies whether General MIDI System On
messages will be received (ON) or not (OFF).
Specifies whether General MIDI 2 System On
messages will be received (ON) or not (OFF).
Specifies whether GS Reset messages will be
received (ON) or not (OFF).