Table of Contents
Advertisement
[Encoding] Page
This is a page for specifying settings on JPEG/H.
264 encoding.
The settings here are linked to the [Encode] item in
the [Basic Setting2] page.
(A p.46 [[Basic Setting2] Page] )
This page can be used during access using
"admin" or "operator".
Click [Advanced Settings] in the side menu, and
0
click [Encoding].
Press the [OK] button to enable the new
0
settings.
If the [OK] button is pressed upon entering an
0
invalid value, a warning message will appear
and the entry will be denied. Press the [Cancel]
button to restore the invalid entry to the value
before the change was made. If you press the
[Cancel] button, other changed items will also be
restored to the values before the change was
made.
There is upper limit to transmission bit rate from
0
the camera. If a bit rate that exceeds upper limit
is specified, this new setting will not be applied.
For details on the maximum transmission limit,
refer to the following.
(A p.20 [Network] )
The contents displayed in "Encoder No.1",
0
"Encoder No.2" and "Encoder No.3" change
depending on the type of encoding and the item
selected.
If the distribution bit rate exceeds 40 Mbps, the
0
specified frame rate distribution fails.
In cases such as high-bitrate distribution at a
0
frame size of 1920´1080 and frame rate of 30
fps (particularly slow pan operations), the
camera image may not appear smooth even on
a high-performance computer. In this case,
lower the [Framesize], [Framerate], and
[Bitrate], and check the image again.
Memo :
H.264 High indicates H.264 High Profile, and H.
0
264 Baseline indicates H.264 Baseline Profile.
Settings
* Setting values with R are default values.
Encode
Select the encoding from "Single-Encode" or
"Multi-Encode".
Single-Encode
0
(A p.52 [When "Single-Encode" is selected in
[Encode]] )
Multi-Encode
0
(A p.53 [When "Multi-Encode" is selected in
[Encode]] )
[Set values: Single-Encode, RMulti-Encode]
[Advanced Settings] Page - [Encoding] Page
52
When "Single-Encode" is selected in [Encode]
Enables only Encoder No.1 out of the three
channels of encoders.
.
Encoder No.1
Select either JPEG, H.264 Baseline, or H.264
High.
[Set values: JPEG, H.264 Baseline, RH.264 High]
9 Framesize
Select the frame size of each JPEG or H.264
screen.
[Set values: R1920´1080, 1280´960, 1280´720,
720´480, 640´480, 640´360, 352´240, 320´240]
9 Framerate
Select a frame rate.
[Set values: R30 fps, 25 fps (JPEG is not
supported), 15 fps, 10 fps, 7.5 fps, 5 fps, 3 fps, 2
fps, 1 fps]
9 Bitrate (when "H.264 Baseline" or "H.264
High" is selected)
Select whether to set the scalable rate control
method for single encoding to CBR (Constant Bit
Rate) or VBR (Variable Bit Rate).
CBR:
0
Data is encoded at a fixed bit rate regardless of
the condition of input video signals. It is easy to
estimate the bit rate. Select from the list of bit
rate ranges.
VBR:
0
The bit rate varies according to the condition of
input video signals. The picture quality is stable
but it is difficult to estimate the bit rate. Select
from the list of bit rate ranges.
[Set values: RCBR, VBR]
[Bitrate range: 64, 128, 256, 384, 512, 768, 1024,
1536, 2048, 3072, 3584, R4096, 8192] kbps
Advertisement
Table of Contents
