Download Print this page

Advertisement

HD NETWORK CAMERA
VN-H37U
Instructions
(Setting)
VN-H137U
VN-H237U
VN-H237VPU
VN-H57U
VN-H257U
VN-H257VPU
VN-H157WPU
LST1244-001C

Advertisement

   Also See for Jvc VN-H37U

   Summary of Contents for Jvc VN-H37U

  • Page 1

    HD NETWORK CAMERA VN-H37U Instructions (Setting) VN-H137U VN-H237U VN-H237VPU VN-H57U VN-H257U VN-H257VPU VN-H157WPU LST1244-001C...

  • Page 2: Table Of Contents

    Getting Started Contents Operations Built-in Viewer Operations ....98 Screen Configuration ..... 99 Picture Quality Setting ....101 Getting Started PTZ Settings ........ 104 Contents ..........2 PTZ Control ......... 106 Unicast Settings ......108 Camera Setting Requirements Multicast Settings ......110 Network ..........

  • Page 3

    How to read this manual Symbols in this manual Caution : Operational precautions are provided. Note : Limitations related to functions and use, and other helpful information are provided. : Reference pages or reference items. Contents of this manual ● This manual explains the system setup using Internet Explorer, and the Built-in Viewer operations.

  • Page 4: Camera Setting Requirements Network

    Camera Setting Requirements If JPEG file size per piece is 120 KB, the total bit Network rate will be: 120 KB x 15 fps = 1800 KB/s = Approx. 14.4 Mbps ● Ensure that there is sufficient network For detailed bit rate settings, see the "Encoding" bandwidth for the data volume to be sent out by camera.

  • Page 5

    ● When distributing only H.264 data Restrictions on the Number of The maximum number of distributions is determined Distributions for Camera by the preset bit rate. When a distribution request that exceeds the maximum number of distributions The maximum number of distributions for is received, this request is denied.

  • Page 6

    Camera Setting Requirements Network List of Protocols and Port Numbers used by Camera (continued) The camera uses the following protocols and port numbers. Ensure that these ports are allowed through the firewall when a firewall is to Insufficient Network Bandwidth be installed.

  • Page 7: Images

    H.264 Profiles User name: admin High profiles can maintain high image quality Password: jvc with a low bit rate, but as the decoder needs to This camera fulfills the ONVIF test specification support high profiles, the processing load on the version 1.02.

  • Page 8: Setting Pages

    Camera Setting Requirements Setting Pages Selection of Languages on Setting Pages There is a radio button for selecting the language at the right top corner of the setting pages, however the language will be automatically set according to the OS environment of your computer. If you select Japanese while using an English-language OS, it may not be correctly displayed because there is no Japanese environment.

  • Page 9

    Uploading and downloading of the Language File You can change the language on setting pages and built-in viewer of the camera. ● Procedure (1) Click "Download" button on the Maintenance page. (2) Save "language.ini" file to the appropriate folder in the computer. (3) Edit the downloaded "language.ini"...

  • Page 10: Pages Available To Each User

    Camera Setting Requirements Pages Available to Each User Enter User Name and Password User name and password entry will be required at the beginning. There are three access authorization levels to camera. The factory settings are as follows. User Default Authorization Name password...

  • Page 11

    operator Pages that Users Have Access to Basic Setting2 [Camera] Restrictions are placed on the pages that users [Encode] have access to. In addition, links on the setting Details [Camera] pages are also displayed according to the [Encoding] access privileges of the user. [Audio](VN-H57U/H257U/ H257VPU/H157WPU only) admin...

  • Page 12: Internet Explorer Setting

    Internet Explorer Setting Settings How to Open the Setting Page Enter IP address of camera in the address bar of Internet Explorer. (for example, the factory default of Ahttp://192.168.0.2B) Enter the user name and password. (The factory default is AadminB and AjvcB) The Built-in Viewer of the camera is displayed.

  • Page 13: Basic Setting1 Page

    Basic Setting1 Page This page sets the network basic. This page can be used during access using AadminB. Click [Basic Setting1]. Memo: ● If you enter the following URL directly into the address bar of Internet Explorer, you can open the [Basic Setting1] page without going through the Built-in Viewer.

  • Page 14

    Internet Explorer Setting Settings (continued) Basic Setting1 Page (continued) Network IP Setting Sets the DHCP client function. To enable the DHCP, connect the camera to the network environment where the DHCP server is running. If you have set IP Setting to DHCP but the DHCP server does not exist, the camera will start with the IP address of 192.168.0.2 and the subnet mask of 255.255.255.0 approximately 2 minutes after startup.

  • Page 15: Basic Setting2 Page

    Basic Setting2 Page This page sets fundamental camera and encoding parameters. This page can be used during access using AadminB or AoperatorB. Click [Basic Setting2]. Memo: ● If you enter the following URL directly into the address bar of Internet Explorer, you can open the [Basic Setting2] page without going through the Built-in Viewer.

  • Page 16

    Internet Explorer Setting Settings (continued) Basic Setting2 Page (continued) Camera ID Text entered here will be written in the H.264 header and the JPEG comment segment (item name: camera). It links to the [Camera ID] of the [Camera] page. (A Page 19) Memo: ●...

  • Page 17

    Encode Select the frame size for each screen of JPEG and H.264 from the following six patterns. Selectable distribution size Commu- Frame Frame I Frame Set value nication Size Rate rate Interval speed H.264 High 1920 x 1080 30 fps 8 Mbps 30 frames 1920x1080 30 fps...

  • Page 18: Camera Page

    Internet Explorer Setting Settings (continued) Camera Page This page sets the camera's parameters. Settings here are linked to the Camera in the "Basic Setting2" page. (A Page 16) This page can be used during access using AadminB or AoperatorB. Click [Advanced Settings] and [Camera]. Memo: ●...

  • Page 19

    Memo: ● Select "Day (Color)" or "Night (B&W)" when you switch the Color or B&W using an alarm trigger. For details, see the [Alarm] page. (VN-H37U, VN-H237VPU) (A Page 35) ● If you press the [OK] button, the settings (except Camera ID) of the [Camera] page will be store in the selected Scenefile.

  • Page 20

    Internet Explorer Setting Settings (continued) Camera Page (continued) Brightness Adjusts the brightness of an image. Increasing the value brightens dark areas, and decreasing the value makes bright areas more pleasing to the eye. [Set values: 5 to Normal to 5] Color Level Adjusts the color level.

  • Page 21

    White Balance Adjusts the white balance. White balance can be adjusted for a light source with a color temperature range of 2300 K to 10000 K. [Set values: ATW-Wide, ATW-Narrow, AWC] ATW-Wide Switches to the Auto-Tracking White Balance (automatic color temperature tracking) Wide mode.

  • Page 22

    Internet Explorer Setting Settings (continued) Camera Page (continued) Maintains the video level according to the object brightness. The priority of motion (by AGC) or the priority of picture quality (by Sense Up) can be selected. If both are set simultaneously, you can set their priority using the [Priority] option. Sets the AGC (automatic gain control) level.

  • Page 23

    Shutter Speed Sets the shutter speed. 1/30 to 1/10000 : Fixes the shutter speed. Auto (1/30 - 1/100) : Varies the shutter speed automatically between 1/ 30 and 1/100 seconds according to the brightness. Auto (1/30 - 1/1000) : Varies the shutter speed automatically between 1/ 30 and 1/1000 seconds according to the brightness.

  • Page 24

    Camera Page (continued) Day/Night Sets video to Black & White mode. Also allows you to select from among 3 levels for automatically activating Black & White mode in low-light (VN-H37U/H57U/ conditions. H257U/H237VPU/ H257VPU/ [Set values: Color, Black & White, Auto Low, Auto Mid, Auto High]...

  • Page 25

    Back Light Selects the backlight compensation function. Enables unwanted light sources to be excluded from the photometry area. Compensation : Disables backlight compensation. Areas 1 to 4 : Select a photometry area from the four areas. [Set values: OFF, Area 1, Area 2, Area 3, Area 4] Photometry area Photometry area Photometry area Photometry area Photometry area Area 1...

  • Page 26: Encoding Page

    Internet Explorer Setting Settings (continued) Encoding Page This page sets JPEG/H.264/MPEG-4 encoding parameters. This entry links to the [Encode] item of "Basic Setting2" page. (A Page 17) This page can be used during access using AadminB or AoperatorB. Click [Advanced Settings] and [Encoding]. Memo: ●...

  • Page 27

    Encode Select the encoding from [Single Encode], [Multi Resolution] or [Multi- Encode]. C options vary depending on the selected encoding system. [Set values: Single-Encode, Multi-Resolution, Multi-Encode1, Multi-Encode2] Single-Encode [Set values: JPEG, H.264 Baseline, H.264 High] Multi-Resolution [Set values: JPEG, H.264 Baseline, H.264 High] Multi-Encode1 [Set values: JPEG + H.264 Baseline, JPEG + H.264 High] Multi-Encode2...

  • Page 28

    Internet Explorer Setting Settings (continued) Encoding Page (continued) From H.264 High, H.264 Baseline and JPEG, you can select one and set Multi-Resolution different frame sizes to up to three channels. The frame rate that can be set is lower than 5 fps. Encoder Encoding Displays the encoding system selected in Multi-Resolution.

  • Page 29

    Multi-Resolution (continued) Encoder Encoding When you use Encoder No.3, turn ON the encoding that you selected in multi No.3 resolution. If you select AOFFB, you will not be able to set Encoder No.3. Display [Set values: JPEG, OFF] Framesize Same as for Encoder No.1. The default value is "640x360"...

  • Page 30

    Internet Explorer Setting Settings (continued) Encoding Page (continued) Multi-Encode1 (continued) Encoder Encoding Displays the encoding system selected in Multi-Encode1. Display No.2 [For JPEG+H.264 Baseline : H.264 Baseline] [For JPEG+H.264 High : H.264 High] Framesize Select the frame size of each JPEG or H.264 screen. Available sizes vary depending on the aspect ratio.

  • Page 31

    The following can be set for Encoder No.1 and Encoder No.2. Multi-Encode2 JPEG(1280 x 960) + MPEG4 (640 x 480) JPEG(1280 x 960) + MPEG4 (320 x 240) JPEG(640 x 480) + MPEG4 (640 x 480) JPEG(320 x 240) + MPEG4 (320 x 240) The frame rate can be set to 15 fps or lower.

  • Page 32

    Internet Explorer Setting Settings (continued) Encoding Page (continued) Multi-Encode2 (continued) Encoder Encoding Displays the "MPEG4" encoding selected for Multi-Encode2. No.2 Display Framesize Displays the frame size selected for Multi-Encode2. Specify the frame rate for Multi-Encode2. Framerate [Set values: 15 fps, 10 fps, 7.5 fps, 1 fps] Bitrate Select whether to set the control rate mode for encoding to CBR (Constant Bit Rate) or VBR (Variable Bit Rate).

  • Page 33: Audio Page

    Audio Page (These features are not available on VN-H37U/H137U/H237U/H237VPU.) This page sets audio parameters. This page can be used during access using AadminB or AoperatorB. ● Click [Advanced Settings] to display the setting menu. ● Click [Audio]. ● Press the [OK] button to enable the new settings.

  • Page 34

    Internet Explorer Setting Settings (continued) Audio Page (continued) Upload Audio File Registers an audio file of the output from the camera's audio output cable or connector when the alarm is activated. No.1 - No.5 To output the registered audio ● Create a file on a computer with the following specifications, and register it to the camera.

  • Page 35: Alarm Page

    Alarm Page This page sets actions to be taken if an alarm occurs. You can set up to five actions (No. 1 to No. 5). This page can be used during access using AadminB or AoperatorB. Click [Advanced Settings] and [Alarm]. Memo: ●...

  • Page 36

    Internet Explorer Setting Settings (continued) Alarm Page (continued) Action Selects the action performed when the alarm is activated. Disable : Performs no action. Mail : Sends an email. Specify the recipient's mail address. The mail subject will be "Alarm from {model name}" (e.g., for VN- H257VPU: "Alarm from VN-H257VPU"), and the sender will be the value for [Camera ID].

  • Page 37

    1st Trigger Select the 1st trigger to perform an action. [Set values: Pin Input1 Make, Pin Input1 Break, Pin Input2 Make, Pin Input2 Break, Position, Audio Detection1, Audio Detection2 (VN-H57U/H257U/H257VPU/H157WPU only), Motion Detection, Tampering Detection, Black & White, Day/Night, Time] Memo: ●...

  • Page 38

    Internet Explorer Setting Settings (continued) Alarm Page (continued) TCP IP Address : Enter the IP address or FQDN of the destination of TCP notification. TCP Port Number : Enter the port number of the destination of TCP notification. (1 to 65535) TCP Data : Enter a character string to be sent for TCP notification.

  • Page 39

    [Set values: 00H00M-23H59M] Day/Night Color : Executes an action when the image changes from Black and White to color. (VN-H37U/ H237VPU/H57U/ Black and White: Executes an action when the image changes from color to H257U/H257VPU/ Black and White. H157WPU only) Memo: ●...

  • Page 40: Alarm Environment Page

    Internet Explorer Setting Settings (continued) Alarm Environment Page This page sets up the alarm environment. This page can be used during access using AadminB or AoperatorB. Click [Advanced Settings] and [Alarm Environment]. Memo: ● Press the [OK] button to enable the new settings. ●...

  • Page 41

    Mail Settings For setting the mail options when [Mail] is selected as the action on the Alarm page. If an SMTP server, a port number or a sender's mail (VN-H57U/H257U/ address has been set, "Preset" will be displayed. H257VPU/H157WPU only) SMTP Server Sets the IP address or FQDN of the SMTP server.

  • Page 42: Storage Page

    Internet Explorer Setting Settings (continued) Storage Page This page sets up data recording. This page can be used during access using AadminB or AoperatorB. Click [Advanced Settings] and [Storage]. Memo: ● Press the [OK] button to enable the new settings. ●...

  • Page 43

    Storage Mode Selects a storage mode. Depending on the selected storage mode, B options vary. [Set values: OFF, FTP Record] If A Storage Mode is set to "FTP Record", FTP Record options will be displayed. FTP Server Sets an IP address of FTP server or FQDN. Path Sets a path name.

  • Page 44

    Internet Explorer Setting Settings (continued) Storage Page (continued) Constant Sets the continuous recording. Encoder Selects an Encoder for continuous recording. Memo: ● You can select an Encoder No. for JPEG file encoding. Interval Sets a recording interval by seconds. [Set values: 1 to 65535] sec File Naming You can select any of three (3) formats of recording file names.

  • Page 45

    Trigger 1 : Sets a condition to record an alarm. [Set values: Position, Motion Detection, Tampering Detection, time] Interval: Unavailable. Trigger 2 : Unavailable. For the VN-H37U/H237VPU Trigger 1 : Sets a condition to record an alarm. [Set values:Position, Motion Detection, Tampering Detection, Day/Night, time] Interval: Unavailable.

  • Page 46

    Internet Explorer Setting memo...

  • Page 47

    memo...

  • Page 48

    Internet Explorer Setting memo...

  • Page 49: Ptz Page

    PTZ Page This page sets the movement speed for Auto Return and Preset Position. This page can be used during access using AadminB or AoperatorB. ● First, set the frame size to 640 x 360 or 640 x 480 in the [Encode] page. (A Page 26) Click [Advanced Settings] and [PTZ].

  • Page 50: Auto Patrol Page

    Internet Explorer Setting Settings (continued) Auto Patrol Page This page sets the Auto Patrol operation to switch and display multiple position images at preset time interval. Set this page to view registered positions in order. This page can be used during access using AadminB or AoperatorB. ●...

  • Page 51

    Click [Advanced Settings] and [Auto Patrol]. Memo: ● Register the position in [PTZ Settings] of Built-in Viewer. (A Page 105) ● Press the [OK] button to enable the new settings. ● If the [OK] button is pressed upon entering an invalid value, a warning message will appear and the entry will be denied.

  • Page 52: Privacy Mask Page

    Internet Explorer Setting Settings (continued) Privacy Mask Page Privacy Mask is a function that can mask a portion of image. Rectangular privacy mask areas can be set for the camera. Drag the blue rectangular areas on the screen to set the privacy mask for them. This page can be used during access using AadminB or AoperatorB.

  • Page 53

    Memo: ● Press the [OK] button to enable the new settings. ● When camera images are acquired by the Built-in Viewer or another client and if this acquisition exceeds the distribution capability of camera, the video images may not appear on the Privacy Mask page.

  • Page 54: Motion Detection Page

    Internet Explorer Setting Settings (continued) Motion Detection Page This page sets the motion detection. This page can be used during access using AadminB or AoperatorB. 13 horizontal by 9 vertical block (For aspect ratio 4:3) Click [Advanced Settings] and [Motion Detection]. 15 horizontal by 9 vertical block (For aspect ratio 16:9) Click [Advanced Settings] and [Motion Detection].

  • Page 55

    Memo: ● If the [OK] button is pressed upon entering an invalid value, a warning message will appear and the entry will be denied. Press the [Cancel] button to restore the invalid entry to the value before the change was made. If you press the [Cancel] button, other changed items will also be restored to the values before the change was made.

  • Page 56: Audio Detection Page

    Internet Explorer Setting Settings (continued) Audio Detection Page (VN-H57U/H257U/H257VPU/H157WPU only) This page sets the audio detection. This page can be used during access using "admin" or "operator". Peak meter Click [Advanced Settings] and [Audio Detection]. Memo: ● The meter turns green when below the detection level threshold, and turns red when above the detection level threshold.

  • Page 57

    No.1, (No.2) Select the item to use with the peak meter for detection confirmation. [Set values: No.1, No.2] No.1 Audio Detection Enables/disables detection of No.1. [Set values: ON, OFF] Level Sets the detection level. [Set values: 0 to 4 to 10] Detection Time Detects audio that continues longer than the set time.

  • Page 58: Tampering Detection Pages

    Internet Explorer Setting Settings (continued) Tampering Detection Pages This page sets the tampering detection. This page can be used during access using "admin" or "operator". Click [Advanced Settings] and [Tampering Detection]. Memo: ● If the [OK] button is pressed upon entering an invalid value, a warning message will appear and the entry will be denied.

  • Page 59: Network Page

    Network Page This page sets the network settings. This page can be used during access using AadminB. Click [Advanced Settings] and [Network]. Memo: ● Press the [OK] button to enable the new settings. ● If you change the settings, the camera will restart. The camera takes about 90 seconds to restart. ●...

  • Page 60

    Internet Explorer Setting Settings (continued) Network Page (continued) IP Setting IP Setting Sets the DHCP client function. To enable the DHCP, connect the camera to the network environment where the DHCP server is running. If you have AenabledB the DHCP but the DHCP server does not exist, the camera will start with the IP address of 192.168.0.2 and the subnet mask of 255.255.255.0 approximately 2 minutes after startup.

  • Page 61: Protocol Page

    Protocol Page This page sets the protocol. This page can be used during access using AadminB. Click [Advanced Settings] and [Protocol]. Memo: ● Press the [OK] button to enable the new settings. ● If the [OK] button is pressed upon entering an invalid value, a warning message will appear and the entry will be denied.

  • Page 62

    Internet Explorer Setting Settings (continued) Protocol Page (continued) Protocol Settings (continued) HTTP Server Port You can change the port number for the built-in HTTP server of the camera. [Set values: 1 to 80 to 65535] Memo: ● To access the camera from Internet Explorer, enter the following in the Internet Explorer address bar when the camera is set to its default settings.

  • Page 63

    Standard Surveillance Sets standard surveillance protocols. Protocol PSIA/ONVIF You can change the standard surveillance protocols. [Set values: PSIA, ONVIF, OFF] JPEG Streaming Selects the JPEG image streaming priority. Priority Selects whether to give priority to the client number for JPEG image streaming or the frame rate.

  • Page 64: Register Information

    Internet Explorer Setting Settings (continued) Register Information Displays valid server certificates. This page can be used during access using AadminB. ● This is displayed when you update the HTTPS and SNMP functions. For directions on updating, refer to [HTTPS and SNMP Function Update Procedure]. (A Page 125)

  • Page 65: Create Server Certificate Page

    Create Server Certificate Page This page is for creating a new server certificate for local certification. This page can be used during access using "admin". ● This is displayed when you update the HTTPS and SNMP functions. For directions on updating, refer to [HTTPS and SNMP Function Update Procedure].

  • Page 66: Multicast Page

    Internet Explorer Setting Settings (continued) Multicast Page (Audio-related functions are only available on the VN-H57U/H257U/H257VPU/H157WPU.) This page specifies manual multicast streaming. This page can be used during access using AadminB or AoperatorB. Click [Advanced Settings] and [Multicast]. Memo: ● To save the changes made to the entire page, press the [OK] button. ●...

  • Page 67

    Encoder No.1 to No.3 Sets the manual streaming of Encoder No.1 to Encoder No.3. Encoding Displays the A EncodeB being set for each encoder.(A Page 27) [Display values: JPEG, H.264 Baseline, H.264 High, MPEG4)] FrameSize Displays the "FrameSize" being set for each encoder. (A Page 26) FrameRate Displays the AFrameRateB being set for each encoder.

  • Page 68: Access Restrictions Page

    Internet Explorer Setting Settings (continued) Access Restrictions Page This page sets the client restrictions. This page can be used during access using AadminB. Click [Advanced Settings] and [Access Restrictions]. Memo: ● Press the [OK] button to enable the new settings. ●...

  • Page 69

    Note: ● If "Allow" is selected, but all IP address fields are left blank, retrieving H.264, JPEG or MPEG-4 by all IP addresses will be denied. An access to the Settings page is not restricted. Additionally, the camera also denies transmission to an IP address if it is specified via API. Memo: ●...

  • Page 70: Time Page

    Internet Explorer Setting Settings (continued) Time Page This page sets the current clock time. This page can be used during access using AadminB. Click [Advanced Settings] and [Time]. Memo: ● Press the [OK] button to enable the new settings. ● If the [OK] button is pressed upon entering an invalid value, a warning message will appear and the entry will be denied.

  • Page 71

    SNTP Sets the SNTP client function. OFF :Does not access to NTP server. :Gets the time by periodical accessing to the specified NTP server. [Set values: OFF, ON] Memo: ● The time is recorded in the JPEG header when distributed by the camera. The time recorded in the JPEG header may not continue immediately before and after the acquisition of time from NTP server.

  • Page 72: Password Page

    Internet Explorer Setting Settings (continued) Password Page This page sets a password. This page can be used during access using AadminB. Click [Advanced Settings] and [Password]. User Name You must set passwords for the "admin", "operator" and "user". Memo: ● You can set up to four users each for "admin", "operator" and "user". ●...

  • Page 73

    ● Remember that you cannot delete the "admin", "operator", and "user" factory default passwords. Note: ● Always handle the password carefully so that you do not forget it. ● If you have forgotten the password, please consult your nearest JVC dealer.

  • Page 74: Focus Page

    Internet Explorer Setting Settings (continued) Focus Page You can adjust the focus from a computer (electric focus) for VN-H57U/H257U/H257VPU/H157WPU. Select the adjustment mode from the pull-down menu and perform adjustment as necessary. This page can be used during access using "admin" or "operator". Click [Advanced Settings] and [Focus].

  • Page 75

    Focus Status Focus adjustment operation status. Ready : Preparing to move. Stop : Not moving. Moving : Currently moving. Error : A moving error occurred. Adjust Mode Sets the adjustment mode. When using an adjustment mode other than "Select" and you do not perform any operation for 3 minutes or more, the mode automatically returns to "Select".

  • Page 76

    Internet Explorer Setting Settings (continued) Focus Page (continued) When you select "Day Focus Adjust" in [B Adjust Mode], the camera automatically enters color mode and Focus Assist mode. Adjust the focus in a bright environment. One Push Auto Click the [Execute] button to automatically adjust the focus. This may take several seconds.

  • Page 77

    When you select "Night Focus Offset" in [B Adjust Mode], the camera automatically enters Black &White mode and Focus Assist mode. Adjust the offset value in a B&W mode environment to achieve focus. Offset When using this function and the offset is set to other than "0", the focus is automatically moved by the offset amount when you enter B&W mode.

  • Page 78: Maintenance Page

    Maintenance Page This page maintains the camera system. This page can be used during access using AadminB. Click [Advanced Settings] and [Maintenance]. Lens (VN-H37U/ Selects the lens type and adjusts the lens. H57U only) Lens Type Select the lens type of camera.

  • Page 79

    Firmware Displays the update, the version and the program number of the firmware. Update Updates the camera firmware and restarts the camera. Your camera settings are saved. Copy the new firmware file to the computer where you use the Internet Explorer, and open the file by pressing the [Browse...] button.

  • Page 80

    Internet Explorer Setting Settings (continued) Maintenance Page (continued) Language File The Language File (the file of languages) can be uploaded or downloaded only when the "English (Custom)" is selected by the language selection radio button. (A Page 8) Download Downloads the Language File. Click [Download] button to download the "language.ini"...

  • Page 81: Led State Page

    LED State Page This page sets the [STATUS] LED indication of the camera. This page can be used during access using AadminB or AoperatorB. Click [Advanced Settings] and [LED State]. Memo: ● Press the [OK] button to enable the new settings. If you press the [Cancel] button, your changes are canceled and the current camera settings are displayed.

  • Page 82: List Of Factory Defaults Of Each Page

    Audio File No.4 – Shutter Speed 1/30 Audio File No.5 – Easy Day/Night Color (VN-H137U/H237U only) Average: Peak Day/Night Color (VN-H37U/H57U/H257U/ H237VPU/H257VPU/ H157WPU only) AF is performed in conjunction with switching modes. Color Average:Peak Black & White Average:Peak Back Light Compensation...

  • Page 83

    Easy Day/Night Color (VN-H137U/H237U only) Time – Day/Night Color (VN-H37U/H57U/H257U/ H237VPU/H257VPU/ H157WPU only) Time Filter Unmask *1: If Action is set to "Position" *2: If Action is set to "Mail Settings" *3: If Action is set to "TCP Data" *4: If Action is set to "UDP Data"...

  • Page 84

    Internet Explorer Setting Privacy Mask Page (A Page 52) Settings (continued) Item Factory Defaults Privacy Mask Brightness List of Factory Defaults of Each Page (continued) Motion Detection Page (A Page 54) Storage Page (A Page 42) Item Factory Defaults Item Factory Defaults Motion Detection Storage Mode...

  • Page 85

    HTTP Password Displayed as *** HTTP Server Port Default passwords are: HTTPS Server Port AadminB : jvc SNMP AoperatorB : jvc AMX Device Discovery AuserB : jvc Protocol Password Re-Input – PSIA/ONVIF LED State Page (A Page 81) JPEG Streaming...

  • Page 86: Miscellaneous Page

    Internet Explorer Setting Settings (continued) Miscellaneous Page This page displays the software information of the camera. This page can be used during access using AadminB, AoperatorB or AuserB. Click [Advanced Settings] and [Miscellaneous].

  • Page 87: Operation Page

    Operation Page This page displays the operation status of camera. This page can be used during access using AadminB or AoperatorB. Click [Advanced Settings] and [Operation]. Total Sending Displays the total TCP/UDP bit rate sent by the camera, and individual bit rates.

  • Page 88: Settings Page

    Internet Explorer Setting Settings (continued) Settings Page Displays the firmware version and the current settings of the camera. This page can be used during access using AadminB or AoperatorB. The following screen is an example of one possible configuration. Click [Advanced Settings] and [Settings].

  • Page 90

    Internet Explorer Setting Settings (continued) Settings Page (continued)

  • Page 92

    Internet Explorer Setting Settings (continued) Settings Page (continued)

  • Page 94

    Internet Explorer Setting Settings (continued) Settings Page (continued)

  • Page 96: Position List Page

    Internet Explorer Setting Settings (continued) Position List Page Displays the preset position information. This page can be used during access using AadminB or AoperatorB. Click [Advanced Settings] and [Position List].

  • Page 97: Patrol Settings Page

    Patrol Settings Page Displays the Auto Patrol information and its settings. This page can be used during access using AadminB or AoperatorB. Click [Advanced Settings] and [Patrol Settings].

  • Page 98: Operations

    Operations Built-in Viewer Operations The camera has the Built-in Viewer. Enter the IP address of camera in the address bar of Internet Explorer. The Built-in Viewer allows H.264/JPEG/MPEG-4 data monitoring and digital PTZ operations. When you are using the JPEG data compression, you can display a series of still images and record still images.

  • Page 99: Screen Configuration

    Screen Configuration Operation menu MENU OFF/ Displays or hides the operation menu. Click [MENU ON], and the operation menu will appear at the left of the page. MENU ON Control Switches the Operation Menu to the Control Menu. Click the [Control] button to adjust the [Image Settings], [PTZ Settings] or [PTZ Control] settings.

  • Page 100

    Operations Built-in Viewer Operations (continued) Screen Configuration (continued) Protocol Selects a protocol to be used when the viewer captures images from the camera. HTTP (Unicast): Allows monitoring the camera with a single viewer. If a packet is lost, the packet data is transmitted again and recovered. RTP (Multicast): Allows multiple viewers to monitor the camera.

  • Page 101: Picture Quality Setting

    Picture Quality Setting Adjusts the picture quality. This page can be used during access using AadminB or AoperatorB. ● While the Viewer Setup Menu is open, click [Control] to switch to the Control Menu. ● Click [Image Settings] to open the Settings screen. Image Settings Click here.

  • Page 102

    Operations Built-in Viewer Operations (continued) Picture Quality Setting (continued) White Balance Selects the white balance control function. Mode ATW-Wide : Selects the Auto-Tracking White Balance (automatic color temperature tracking) Wide mode. Adjusts the white balance automatically according to the color temperature of the light.

  • Page 103

    C Day/Night Sets video to Black & White mode. Also allows you to select from among 3 (VN-H37U/H57U/ levels for automatically activating Black & White mode in low-light H257U/H237VPU/ conditions. H257VPU/H157WPU only) Mode Color : Keeps color mode activated at all times.

  • Page 104: Ptz Settings

    Operations Built-in Viewer Operations (continued) PTZ Settings Sets the camera preset position. ● This page can be used during access using AadminB or AoperatorB. ● While the Viewer Setup Menu is open, click [Control] to switch to the Control Menu. ●...

  • Page 105

    Preset Position Sets the camera preset position. Position Selects a Position. [Set values: HOME, 1 to 19] Title Displays the current title. To register or change the title, enter a title here. (The title can be entered using up to 32 alphanumeric characters or up to 16 dual-byte characters.) Press the [Register] button, and the new position will be registered.

  • Page 106: Ptz Control

    Operations Built-in Viewer Operations (continued) PTZ Control Controls the PTZ function. You can set up the PTZ from the [PTZ Settings] page. (A Page 104) ● This page can be used during access using AadminB or AoperatorB. ● While the Viewer Setup Menu is open, click [Control] to switch to the Control Menu. ●...

  • Page 107

    Auto Starts or stops automatic patrol. Press the [Start] button to start automatic patrol. The [Stop] button is displayed Function during Auto Patrol. Press the [Stop] button to stop automatic patrol. Preset You can select a preset position and click the [GoTo] button to move to it. If the selected position is already registered, the camera moves to the selected Position position.

  • Page 108: Unicast Settings

    Operations Built-in Viewer Operations (continued) Unicast Settings You can set the HTTP port and the JPEG frame rate in Unicast. This page can be used during access using AadminB or AoperatorB. ● When the Control Menu is open, click [Viewer Setup] to switch to the Viewer Setup Menu. ●...

  • Page 109

    HTTP Port You can change the port number to be used when the client computer accesses to the camera via HTTP. Specify the same value as the parameter being set on the camera's Protocol Page. (A Page 61) [Factory default: 80] JPEG Frame Sets a frame rate for image acquisition by the viewer.

  • Page 110: Multicast Settings

    Operations Built-in Viewer Operations (continued) Multicast Settings You can set up an IP addresses for images and audio received in multicast, and set up the multicast ports. This page can be used during access using AadminB or AoperatorB. ● When the Control Menu is open, click [Viewer Setup] to switch to the Viewer Setup Menu. ●...

  • Page 111

    Video settings Multicast IP You can change the multicast IP address. Address [Factory default: 225.0.1.1] Multicast Port You can change the multicast port number. [Factory default: 49152] Audio settings (VN-H57U/H257U/H257VPU/H157WPU only) Multicast IP You can change the multicast IP address. Address [Factory default: 225.0.3.1] Multicast Port...

  • Page 112: On Screen Display Settings

    Operations Built-in Viewer Operations (continued) On Screen Display Settings Sets a display item on the viewer screen. An image is overlaid by characters on the Built-in Viewer. This page can be used during access using AadminB or AoperatorB. ● When the Control Menu is open, click [Viewer Setup] to switch to the Viewer Setup Menu. ●...

  • Page 113

    memo...

  • Page 114

    Operations memo...

  • Page 115

    memo...

  • Page 116

    Operations memo...

  • Page 117

    memo...

  • Page 118: Settings Related To Audio Monitor

    Operations Built-in Viewer Operations (continued) Settings related to Audio Monitor (VN-H57U/H257U/H257VPU/H157WPU only) This is used to make settings related to sending and receiving audio via the Built-in Viewer. ● This page can be used during access using "admin" or "operator". ●...

  • Page 119

    Receiving Specifies settings for receiving audio streamed from the camera. settings Receive Enables/disables reception. To receive audio streams, select "ON". Protocol Selects the stream type for receiving audio. Select "HTTP (Unicast)" to recover by retransmission when packet loss occurs. Select "RTP (Multicast)" to monitor camera audio from multiple client computers.

  • Page 120: Other Setting

    Operations Built-in Viewer Operations (continued) Other Setting When you are using the JPEG data compression, you can display still images. You can rename the folder which stores a captured file. This page can be used during access using AadminB or AoperatorB. ●...

  • Page 121: Exiting The Built-in Viewer

    Exiting the Built-in Viewer Click the [ ] button at the right top corner of the window to exit the viewer. Click here. Memo: ● When you start the Built-in Viewer in the next time, start the Internet Explorer and enter the URL of Built-in Viewer in the address bar of the explorer.

  • Page 122: Others

    Others Troubleshooting Reference Symptom Possible Causes and Actions Taken Page ● IP address "192.168.0.2" and subnet mask A Page 14 I do not know the IP address "255.255.255.0" are set by default during factory of the camera. shipment. ● If you have set the [IP Setting] to ADHCP EnableB and if you start the camera on the LAN where no DHCP server exists, you can start the camera with the factory default IP address.

  • Page 123

    Reference Symptom Possible Causes and Actions Taken Page ● Start manual multicast streaming from the A Page 66 Multicast images do not play. [Multicast] page of the camera. ● When you receive multicast streaming using the A Page 110 Built-in Viewer, check to see that multicast address and port number matches between the [Multicast] page of camera and the Built-in Viewer settings.

  • Page 124

    Others Troubleshooting (continued) Reference Symptom Possible Causes and Actions Taken Page ● Multicast streaming may be blocked by the A Page 100 I cannot receive an alarm via Windows 7 Firewalls. In that case, you can go TCP/UDP. through the firewalls as follows. Select [Start] - [Control Panel] - [System and Security].

  • Page 125: Https And Snmp Function Update Procedure

    HTTPS and SNMP Function Update Procedure The camera's default settings do not support using the HTTPS and SNMP functions. To use the HTTPS and SNMP functions, use the firmware update function via the Maintenance Page, and update to the firmware version designated below. (A Page 79) Acquire firmware for updating via the site below.

  • Page 126

    Others memo...

  • Page 127

    memo...

  • Page 128

    LST1244-001C © 2012...

Comments to this Manuals

Symbols: 0
Latest comments: