Direct drive super fast, slow and accurate pan/tilt mechanism, ip66 + ik10 housing, performance at wide range temperature and super durable indoor & outdoor camera (2 pages)
Hd ip ptz camera, outdoor hd ip ptz camera (98 pages)
Summary of Contents for JVC VN-H557U
Page 1
HD IP PTZ CAMERA VN-H557U INSTRUCTIONS For Customer Use: Enter below the Model No. and Serial No. Please read the following before getting started: which is located on the body. Thank you for purchasing this product. Retain this information for future reference.
Safety Precautions This unit is able to divert lightning conduction to itself and the connecting cables to a certain extent but this is not 100 Consult your dealer as special % guaranteed. For installation locations technique is required when installing that are likely to suffer lightning strikes, be this product.
Features Privacy Mask function This function allows you to blank out areas that you do not wish to display in the location to be recorded. Support for PoE (Power over Ethernet) This camera supports PoE (IEEE802.3af) and Motion Detection Feature enables power supply through a LAN cable.
Storage and Operating Environment Memo : States restrictions on the functions or use of this equipment. For reference purposes. VN-H557U is an indoor camera. It cannot be used : Indicates the page numbers or items to outdoors. refer to.
Page 6
Transportation Maintenance Do not throw away the original box of the unit. Turn off the power before performing Keep it and use it for transporting the unit in maintenance. future. Wipe using a soft cloth. Wiping with thinner or benzene may melt or tarnish its surface.
Our company shall not be liable for any Auto Focus accidental damage caused to the data stored in Auto Focus operation can be performed on this the card. Please back up important data on product after the pan/tilt/zoom (PTZ) operation devices such as a computer.
Page 8
The video standard of this product is set to Others “NTSC” by default. If your region uses the PAL This camera will perform the initial operation of format, you can switch to “PAL” on the pan/tilt/zoom upon powering on. [Maintenance] page. Do not subject the lens to strong light source Flicker can be reduced by setting to “PAL”...
Accessories Before starting an important recording, be sure to perform a test recording in order to confirm that a normal recording is possible. Before mounting this product, please check to We shall not be liable for the loss of recordings ensure that all the following accessories and or opportunities in the event that recording attachments are available.
Name of Parts A Cable cover Remove the cable cover during installation or connection. VN-H557U To mount the camera with the cables pulled out from the side, remove the center window cover. Camera When attaching the cable cover, pull out the center window cover and pass the cables through it.
Page 11
Ceiling mount bracket G I/O Connector Connect an audio cable or alarm signal cable. Signal Name AUDIO IN AUDIO IN GND AUDIO OUT AUDIO OUT GND ALARM OUT1 ALARM OUT1 COM ALARM OUT2 ALARM OUT2 COM ALARM IN1 ALARM IN1 COM ALARM IN2 ALARM IN2 COM H [10BASE-T/100BASE-TX] LAN cable...
About SD Cards Inserting a SD Card Get ready a formatted SD card in advance. Inserting the SD card in the wrong orientation may This camera enables recorded videos to be saved damage the camera or the SD card. Before to the SD card (sold separately) inserted into the inserting a SD card, ensure that the orientation is card slot.
Alarm Input/Output Signal Alarm Output Signal Connect to alarm devices such as alarm, indicator, light or buzzer. Alarm Input Signal Alarm output signal is an open collector output insulated with photo coupler. Connect to sensors such as infrared sensors, door sensors, metal sensors and manual switches.
Operating Environment Network Ensure that there is sufficient network Recommended Computer bandwidth for the data volume to be sent out by Specifications the camera. Do not send multicast stream that : Windows 8 Pro, Windows 7 exceeds the bandwidth. If the entire bandwidth Professional (SP1), Windows XP is used by the multicast stream, control of this Professional, or Home Edition...
Network Jitter User Name : admin When there is considerable network jitter, delay Password : jvc time may be prolonged and the image frame rate This camera fulfills the ONVIF Profile S. may drop. In the case of H.264, noise interference may occur and playback may fail.
Images Uploading and Downloading of the Language File You can change the language on settings page and H.264 Profiles “Built-in Viewer” of the camera. The camera supports both the H.264 Baseline Profile and H.264 High Profile standards. Procedure High Profiles can maintain high image quality with 1 Open the Settings page.
There are three access authorization levels to the [Protocol] camera. The factory settings are as follows. admin [Multicast] All operations and setting changes are allowed. [Access Restrictions] (Default Password: “jvc”) [Time] operator [Password] The following items cannot be operated, and setting changes are not permitted. [Basic [Maintenance]...
Set up an IP address by either using wire (ceiling) into the ceiling. the JVC-VN-IP SettingTool (included on the supplied CD-ROM) or turning the power supply of each camera on separately to avoid duplication.
Page 19
5 Remove the protective sheet attached Alarm signal cable to use to the lens. Length of 50 m or shorter Note : UL1007, UL1015 or equivalent products If there is a possibility that the lens may be AWG#28 to AWG#20 or equivalent scratched while work is in progress, remove the products protective sheet only when you are about to turn...
Mounting the Camera 4 Fix the camera on the ceiling mount bracket using the provided screw (M4). 1 Insert a SD card. To record to an SD card, insert the SD card in advance. (A p.12 [Inserting a SD Card] ) 2 Mount the camera onto the ceiling mount bracket.
Configure the Internet Explorer settings in order duplication. Set up an IP address by either using to establish connection between the computer the JVC-VN-IP SettingTool (included on the and the camera. supplied CD-ROM) or turning the power supply of each camera on separately to avoid duplication.
Step2 Internet Explorer Setting Select [Enable]. 1 Launch the Internet Explorer on the computer. 2 When proxy settings are enabled in the Internet Explorer, follow the steps below to disable the proxy of the Internet Explorer. A Select in the sequence of [Tools]-[Internet 4 If ActiveX controls and plug-ins of Options]-[Connections]-[LAN Settings].
[YES] button to proceed. 2 Enter the user name and password (login as “admin”). A Enter the user name. (default password is “admin”) B Enter a password. (default password is “jvc”) C Click OK. Step2 Internet Explorer Setting...
Access the [TOOL_E] folder of the supplied When selecting “DHCP Disable”: CD-ROM disc, and search for the camera in Select “DHCP Disable” for the [Network] option. the LAN using the “JVC-VN-SearchTool” of Then, enter required values in [IP Address], this folder. [Subnet Mask], and [Default Gateway].
Page 25
B Select [Time Zone]. C Click to confirm. Memo : For information on the network settings, please consult your network administrator. If you enter the following URL directly into the address bar of Internet Explorer, you can open the [Basic Setting1] page after logging in as “admin”...
URL of the camera, refer to the following. (A p.21 [IP Address Setting Procedure] ) 2 Enter the user name and password. The factory default is “admin” and “jvc”. After entering a correct user name and password, the Built-in Viewer of the camera is displayed.
Built-in Viewer Menu List - [Protocol] (*1) .......... p.57 - [Protocol Settings] ....... p.57 The following items can be set. Depending on the - [Standard Surveillance Protocol] ..p.58 logged-in user name, some items may not be set due to the access authorization. In such case, - [JPEG Streaming] ........
[Basic Setting1] Page Subnet Mask Sets the subnet mask of camera. [Factory default: R255.255.255.0] This page is for performing basic setting related to the network. Default Gateway This page can be used during access using Sets the default gateway of camera. “admin”.
[Basic Setting2] Page Scenefile You can select the setting that is suitable for the shooting scene. You can select the following eight This is a page for specifying the basic settings scenes. You can customize the camera page related to the camera and encoding. You can settings (except Camera ID) stored in “Scenefile”.
Encode Select the frame size for each screen of JPEG and H.264 from the following six patterns. o Selectable distribution size H.264 High 1920´1080 30 fps (Frame size: 1920´1080, frame rate: 30 fps, communication speed: 8 Mbps, bit rate: CBR, I Frame Interval: 30 frames) H.264 High 1920´1080 5 fps (Frame size: 1920´1080, frame rate: 5 fps,...
[Advanced Settings] Page Memo : You can enter up to 40 characters consisting of alphabets (both upper case and lower case), [Camera] Page numerals, parentheses, commas, periods, spaces and hyphens. This is a page for specifying the camera settings. All characters entered in the JPEG comment Settings here are linked to the Camera item in the segment will be saved, but some characters [Basic Setting2] page.
Page 32
Iris Black Level You can set the convergence level for the iris. Adjusts the black level. Setting the value to “Low” Auto +1: darkens the video image. Converges to a level brighter than “Auto”. [Set values: Low, RNormal] Auto: Memo : This setting is used under general If the black level is set to “Low”, this may be too circumstances.
Page 33
White Balance For selecting the white balance control feature. Maintains the video level according to the object ATW-Wide: brightness. The priority of motion (by [AGC]) or the Switches to the Auto-Tracking White Balance priority of picture quality (by [Sense Up]) can be (automatic color temperature tracking) Wide selected.
Page 34
Easy Day/Night Note : When Sense Up is set to a value other than Sets video to Black & White mode. Also allows you “OFF”, flickers occur under the light of to select from among 3 levels for automatically fluorescent or mercury lamps. This is not a activating Black &...
[Encoding] Page Settings This is a page for specifying settings on JPEG/H. 264 encoding. The settings here are linked to the [Encode] item in the [Basic Setting2] page. (A p.29 [[Basic Setting2] Page] ) This page can be used during access using “admin”...
Page 36
Encoder No.1, Encoder No.2 and Memo : Encoder No.3 When “VBR” is set, the [Bitrate] setting uses 30 fps as a reference value. Select either JPEG, H.264 Baseline, or H.264 When the frame rate is low, the actual bitrate High. distributed may drop.
[Audio] Page Memo : You can specify the file size by combining the This is a page for specifying the audio settings. frame size and the picture quality level. This page can be used during access using Select between Level 1 and 7. The picture “admin”...
Audio Upload Communicate Audio File No.1 to No.5 For setting the audio transmission mode. For registering the audio file to be output from the Half Duplex: camera’s audio cable or terminal when an alarm is Stops the audio transmission from the camera activated.
[Alarm] Page No.1 to No.5 This page sets actions to be taken if an alarm occurs. You can set up to five actions (No. 1 to No. Action Selects the action to perform when the alarm is This page can be used during access using activated.
Page 40
JPEG Attachment: 1st Trigger Specify whether or not to attach an image file to Select the 1st trigger to perform an action. the mail. To attach JPEG images, check the [Set values: RPin Input1 Make, Pin Input1 Break, Attach box and select the transmission channel. Pin Input2 Make, Pin Input2 Break, Position, Audio Encoder: Detection1, Audio Detection2, Motion Detection,...
Page 41
Trigger Position Number UDP IP Address: Set the preset position number to be used as the Enter the IP address or FQDN of the destination trigger when [1st Trigger] is set to “Position”. of UDP notification. [Set values: 0 to 99] UDP Port Number: Memo : Enter the port number of the destination of UDP...
[Alarm Environment] Page Port Number Input the port number. This page sets up the alarm environment. [Set values: 1 to R25 to 65535] This page can be used during access using “admin” or “operator”. Send Mail Address Click [Advanced Settings] in the side menu, and click [Alarm Environment].
[FTP Recording] Page FTP Recording This page describes setting procedures related to recording. Record Status This page can be used during access using For selecting a recording mode. Selecting “ON” “admin” or “operator”. displays options after [Record Status]. Click [Advanced Settings] in the side menu, and [Set values: ON, ROFF] click [Record Status].
Page 44
Constant 9 Trigger1, Interval, Trigger2 Trigger1: Settings for performing constant recording. For selecting the first trigger for performing 9 Encoder alarm recording. [Set values: RPin Input1 Make, Pin Input2 Make, For selecting the encoder for performing constant Pin Input1 Break, Pin Input2 Break, Position, recording.
[SD Card Recording] Page 9 Pre-Trigger For setting the FTP pre-recording trigger time This page describes setting procedures related to (recording time before alarm input) in seconds. SD card recording. [Set values: 0 to R5 to 60]sec This page can be used during access using “admin”...
Page 46
9 Status Settings Displays the mount status of the SD card. Mounted: A SD card is mounted to the camera. Recording to or playback of data on the card can be performed. Unmounted: A SD card is not mounted to the camera. Recording to and playback of data on the card are disabled.
Page 47
9 Status 9 Network Outage This is indicated as “Recording” when recording is Performs recording to the SD card when the link between the camera and the network is in progress, and as “No Recording” when recording disconnected. is stopped. When only [Alarm] is selected, the Memo : status is indicated as “Recording”...
Page 48
9 Interval 9 Easy Day/Night This is available when both [Trigger1] and This is enabled when “Easy Day/Night” is selected [Trigger2] are set. for the [Trigger1] item. Specify the maximum interval between each Color: trigger for [Trigger1] and [Trigger2]. Executes alarm recording when the image switches from black-and-white to color.
[PTZ] Page Return Time This item sets the time to return the operation with This page allows you to specify the Auto Return, Auto Return. Move Preset Position and Auto Flip settings. [Set values: R1, 2, 3, 5, 10, 20, 30, 60] minutes This page can be used during access using “admin”...
Tilt Limit Basic operation of Pan Limit This item sets the movable range of the tilt (vertical) When [Pan Limit] is set to “ON”, panning is only operation during manual operation. available in the effective area. When this item is set to 10 °, the movable range of When the camera is moved to prohibited area by the tilt operation is from 10 °...
[Privacy Mask] Page Auto Flip Privacy Mask is a feature that enables masking of a portion of the video image. Auto Flip You can set 8 rectangular privacy masks for this Set this item when shooting objects that pass right unit.
Privacy Mask Memo : Upon opening the Mask Setting screen, Auto For specifying whether to activate the Privacy Mask Flip switches temporarily to “OFF”. After closing feature. the Mask Setting screen, the original settings When this is set to “ON”, the privacy mask specified are restored.
[Motion Detection] Page Settings This page is for setting motion detection. This page can be used during access using “admin” or “operator”. The area valid for motion detection is displayed in blue. When motion is detected, the area around the screen is highlighted in red.
[Audio Detection] Page Peak Meter (No.1, No.2) This page sets the audio detection parameters. For selecting the target for detection using the peak Audio detection is activated when the audio sound meter displayed at the top of the setting screen. input to the audio input terminal from a microphone, A sound level below the detection level is indicated etc.
[Tampering Detection] Page Settings This page sets the tampering detection parameters. Such cases are usually thought to be caused by blocked lenses or obstructing objects. This page can be used during access using “admin” or “operator”. Click [Advanced Settings] in the side menu, and click [Tampering Detection].
[Network] Page IP Address Sets the IP address of camera. This page sets the network settings. [Factory default: 192.168.0.2] This page can be used during access using “admin”. Subnet Mask Click [Network] in the side menu. Press the [OK] button to enable the new Sets the subnet mask of camera.
[Protocol] Page Protocol Settings This page sets the protocol. Sets the protocols. This page can be used during access using “admin”. HTTP/HTTPS Memo : For selecting the protocol to use. Press the [OK] button to enable the new [Set values: RHTTP, HTTPS] settings.
[Multicast] Page SNMP For setting SNMP. This page is for setting manual multicast [Set values: ON, ROFF] transmission. All items can be set when you log in as “admin”. AMX Device Discovery Protocol If you log in as “operator”, you are only allowed to start or stop transmission.
Page 59
9 Framesize EncoderNo.4 Displays the [Framesize] settings specified for For setting manual distribution by EncoderNo.4. each encoder. (A p.36 [ Framesize ] ) Destination Address 9 Framerate For specifying the destination address for audio Displays the [Framerate] for multicast distribution. transmission.
[Access Restrictions] Page Client Address This page is for setting client restrictions. Restrictions may be imposed on clients accessing This page can be used during access using the camera using the IP address. “admin”. Click [Advanced Settings] in the side menu, and Access Restriction click [Access Restrictions].
[Time] Page SNTP Server Sets an IP address of NTP server. This page sets the current clock time. [Factory default: 0.0.0.0] This page can be used during access using “admin”. Interval Press the [OK] button to enable the new settings. Sets a unit and values of measurement for the time If the [OK] button is pressed upon entering an interval at which to access the NTP server.
[Password] Page admin, operator, user This page sets a password. This page can be used during access using User Name “admin”. You must set passwords for the “admin”, “operator” Note : and “user”. Be sure to handle the password carefully in case Memo : you forget it.
[Maintenance] Page Firmware This page maintains the camera system. This page can be used during access using Update “admin”. Updates the camera firmware and restarts the Click [Advanced Settings] in the side menu, and camera. click [Maintenance]. Copy the new firmware file to the computer where you use the Internet Explorer, and specify the file Settings by clicking the [Browse...] button.
Page 64
Language File Installation Mode The Language File (the file of languages) can be Installation Mode uploaded or downloaded only when the “English (Custom)” is selected by the language selection You can change the vertical orientation of the camera’s installation position. radio button.
[Miscellaneous] Page [Operation] Page This page displays the software information of the The operation status of the camera is displayed. camera. This page can be used during access using This page can be used during access using “admin” or “operator”. “admin”, “operator”...
[Settings] Page [Position List] Page Displays the firmware version and the current Displays information on the preset position. settings of the camera. This page can be used during access using This page can be used during access using “admin” or “operator”. “admin”...
List of Factory Defaults of Encoding Page Each Page Item Factory Settings Encoder No.1 Encoding H.264 High Framesize 1920´1080 Camera Page Framerate 30 fps Item Factory Settings Bitrate CBR 4096 kbps Camera ID VN-H557 I Frame 30 Frame Scenefile General Interval Iris Auto...
Page 68
Alarm Page Alarm Environment Page Item Factory Settings Item Factory Settings Action Disable SMTP Server 0.0.0.0 1st Trigger Pin Input1 Make Port Number Max. Interval Send Mail Address 2nd Trigger Disable POP before SMTP Disable Action Position Number(*1) POP Server 0.0.0.0 Mail Settings (*2) Unset...
Page 69
SD Card Recording Page Audio Detection Page Item Factory Settings Item Factory Settings SD Card No.1,2 No.1 Status No.1 Audio Detection Record Status Detection Sensitivity Status No Recording Detection Time 1000 ms Recording Mode - No.2 Audio Detection Alarm Settings Detection Sensitivity 1st Trigger Pin Input1 Make...
Built-in Viewer Operation If the display or configuration of the open window appears strange, check the computer settings as follows: The camera comes with a Built-in Viewer. Enter the IP address of the camera in the address A Select [Start]-[Control Panel]-[Appearance bar of Internet Explorer to start up the Built-in and Personalization].
Built-in Viewer Screen Viewer Setup Configuration Switches the Operation Menu to the Viewer Setup Menu. Click this when you want to set [Unicast], [Multicast], [On Screen Display], [Audio Monitor], Memo : [Other], or play back videos on the [SD card]. Built-in Viewer settings are stored in cookies.
Page 73
Encoder Note : Even when [Communicate] on the [Audio] page Select the encoder No. for streaming. is set to “Full Duplex”, audio from the camera’s [Set values: RNo.1, No.2, No.3] microphone may be interrupted momentarily Memo : when the [Speech] button is pressed. This is not When [Protocol] is set to “RTP(Multicast)”, you a malfunction.
[Control] White Balance For selecting the white balance control feature. [Image Settings] Settings 9 Mode ATW-Wide: Adjusts the picture quality. Switches to the Auto-Tracking White Balance This page can be used during access using (automatic color temperature tracking) Wide “admin” or “operator”. mode.
Page 75
9 [OnePushAWC] button Back Light Compensation Executes AWC (automatic white balance control). Set this feature when there is a bright light source in the same direction as the object. Enables Memo : unwanted light sources to be excluded from the To execute [OnePushAWC], fill the screen photometry area.
[PTZ Settings] This item sets the pan/tilt/zoom (PTZ) functions. This page can be used during access using “admin” or “operator”. While another menu is open, click [Control], followed by clicking [PTZ Settings] in the operation menu to open the setting screen. Preset Position Sets the camera preset position.
Page 77
Mode Auto Pan Return: Move between [Start] and [Return] from [Start] toward [Return]. You can set a start and return position manually. Memo : During auto pan, the [Start] settings are used for zoom and focus. Speed Select the auto pan operation speed. [Set values: Low, RMiddle, High] Start, Return For setting [Start] and [Return] of the operation.
[PTZ Control] Pan / Tilt / Zoom Pan / Tilt operation: Operates the pan/tilt/zoom (PTZ) function. Operate Press the arrow buttons to move the display area the camera to adjust the direction, angle and focus. in the direction indicated by the arrow. Release This page can be used during access using the button to stop the movement.
Page 79
Auto Function Memo : Pressing the [+], [-] or [Focus] button releases Select an Auto action, and press the [Start] or the Easy AF mode and activates the Manual [Stop] button. mode. [Start] button: The “Easy AF” function may not focus properly Start the selected Auto function.
[Viewer Setup] HTTP Port You can change the port number to be used when the client computer accesses to the camera via [Unicast] Settings HTTP. Set to the same value as [HTTP Server Port] of the You can set the HTTP port and the JPEG frame rate [Protocol] page.
[Multicast] Settings Memo : Set the multicast IP address and multicast port You can set the individual IP address and multicast to the same value specified for the destination port for video images and audio received via address and destination port respectively in the multicast.
[On Screen Display] Settings Position Title When “ON” is selected, the position title is Sets a display item on the viewer screen. For the Built-in Viewer, characters are displayed as displayed in the lower left of the screen. overlay on the video image. [Set values: ON, ROFF] This page can be used during access using Disp MD / Tampering / Audio Detection...
[Audio Monitor] Settings Receive For specifying settings related to audio For specifying settings related to reception of audio transmission on the Built-in Viewer. distributed by the camera. This page can be used during access using “admin” or “operator”. When the Control Menu is open, click [Viewer Setup] to switch to the Viewer Setup Menu.
[Other] Settings Speech When you are using the JPEG data compression, For specifying settings related to audio you can record still images. transmission from a computer to the camera. You can rename the folder which stores a captured file. This page can be used during access using “admin”...
[SD Card] Operation Screen Clicking the [SD Card] button on the Built-in Viewer screen displays the operation menu of the SD card. On the SD card operation screen, you can play back videos stored in the SD card. These videos can also be saved to a computer.
Page 86
List Details: [Export] button: Displays the “Starting Date/Time” and “Event Pressing the button displays a confirmation Type” in sequence for events starting from screen and saves the video. While saving of the video is in progress, the the recording with the latest starting date/ button switches to a [Cancel] button display.
Page 87
List of Video Control Menu Buttons Performs fast forward at the speed specified in Moves in the reverse direction by the amount of time specified in N and pauses playback. For selecting the amount of time to move in M and O.
Exiting Built-in Viewer Click the [´] button at the right top corner of the window to exit the viewer. Memo : When you start the Built-in Viewer the next time, start up Internet Explorer and enter the URL of the Built-in Viewer into the address bar. For example, if the IP address of the camera is 192.168.0.2, enter the URL as follows: http://192.168.0.2/...
N If you have a computer connected to the same the resistance and prevent the voltage from being LAN, search for the IP address using properly supplied.) “JVC-VN-SearchTool” on the computer. N Connect using a cable with a thickness/length specified for this product. (A p.18 [Installation and Connection I cannot display the Settings page of the camera.
Page 90
A white zone appears in the Built-in Viewer. Multicast images do not play. For some computers, if [Start]-[Control N Start manual multicast transmission from the [Multicast] page of the camera. Panel]-[Adjust screen resolution]-[Make text and (A p.58 [[Multicast] Page] ) other items larger or smaller] is set to “Medium - 125%”...
Page 91
Videos sent via TCP do not play. I cannot receive an alarm via TCP/UDP. The camera can transmit a maximum of 40 videos The port may be blocked by the Windows via TCP, and a maximum of 20 Built-in Viewer can Firewall.
Page 92
The camera pans automatically Video recording and playback cannot be performed when a SD card formatted on the VN-H37U/VN-H57U series is used. When [Auto Cleaning] is set to “ON”, this is not an abnormality. The SD cards formatted on the VN-H37U/ N Check the current settings of [Auto Cleaning].
Consumable Parts The following are consumable parts. They must be replaced once they reach their lifetime. The lifetime is only an estimation and differs according to the usage environment and conditions. Replacement of consumable parts is chargeable within the guarantee period. Consumable Parts Estimated Lifetime Lens section...
Appendix (Restrictions during Multi-encoding) Possible Encoder No.1 and No.2 Setting Combinations During multi-encoding, there is a limit to the total number of pixels per unit time that can be encoded simultaneously by three encoders (total frame size and frame rate processed by each encoder). Encoder No.2 cannot be set to a frame size with a resolution higher than that of Encoder No.1.
Restrictions when Encoder No.1 is set to 1920´1080 30 fps When Encoder No.1 is set to a frame size of 1920´1080 and a frame rate of 30 fps, Encoder No.3 will be subject to restrictions on the settable values depending on the setting of Encoder No.2.
Specifications Network section Image : JPEG, H.264 High Profile, compression H.264 Baseline Profile Overall format Alarm input : Non-voltage contact signal Frame size : 1920´1080, 1280´960, input (500ms and above); circuit 1280´720, 720´480 (D1), current during low level: 5 mA 640´480, 640´360, 352´240, and below;...
Page 98
SD card section Ceiling mounting hole [Unit: mm (inch)] SDHC card (sold separately) Class10 (or higher) SDHC card (16 to 32 GB) テンプレー ト ø 120 (4 46/64) Cards with a guaranteed operating temperature of Camera outer TEMPLATE diameter 85 °C or higher are recommended. カメラ本体外径...
Need help?
Do you have a question about the VN-H557U and is the answer not in the manual?
Questions and answers