P4 Other Page; P3 Tc Page - Sony PDW-HR1 Operation Manual

Item Setting
F3: PB VOL Sets the playback audio level of audio
channels 5 to 8.
The playback audio level can be adjusted
within the range from –200 to +200 (–∞ to
+12 dB) by turning the PUSH SET knob.
Sub-item
F1: A5 VOL Playback audio level of
F2: A6 VOL Playback audio level of
F3: A7 VOL Playback audio level of
F4: A8 VOL Playback audio level of
F5:
F6: EXIT
b) Enables or disables mixing output of
F4: MIX/SWAP
audio/voice signals.
OFF: Do not output
ON: Output
F5: SPEAKER Enables or disables output from this
unit's speaker.
OFF: Do not output
ON: Output
F6: AU METER Selects the display mode of the audio
level meters.
FULL: Display the range from –60 dB to
FINE: Display a magnified section with
a) To enable this setting, the following settings are also required, in the same
way as for volume operations for channels 1 to 4.
- On the control panel, set the VARIABLE/PRESET switch for playback
to "VARIABLE".
- Set setup menu item 131 AUDIO VOLUME to "each".
b) Displayed only when the PDBZ-UPG03 Software Upgrade Key or PDBK-
MK1 option board is installed.

P3 TC page

Item Setting
F1: TC UB When the PRESET/REGEN switch is set
to "PRESET", selects whether the user
bits of the timecode generator are
synchronized to the internal clock.
FIX: Do not synchronize user bits.
TIME: Synchronize user bits to the
F2: (Unassigned function button)
F3: (Unassigned function button)
F4: DF/NDF Selects the drop-frame mode for the
internal timecode generator and the
counter in 59.94i/59.94P/29.97P mode.
DF: Drop-frame mode
NDF: Non-drop-frame mode
52
Basic Function Menu Operations
a)
audio channel 5
audio channel 6
audio channel 7
audio channel 8
–
Exit the playback audio
level setting sub-menu.
0 dB.
0.25 dB step marks.
internal clock.
Item Setting
F5: PDPSET When the system frequency is set to
1080/59.94i, 1080/29.97P, or 720/
59.94P, presets the timecode of the A
frame of the pulldown sequence.
24F TC.: Reference timecode for A
frame
30F TC.: Timecode after pulldown
conversion from 24-frame timecode
Sub-Item
F1:
F2:
F3: B
F4: b
F5: SET
F6: EXIT
F6: TCR Selects the type of timecode to display in
the time data display area.
TC: Display TC.
VITC: Display VITC.

P4 OTHER page

Item Setting
F1: ALRM LOG Displays an alarm log screen.
Sub-Item
F1: ALARM
F2: DATE
F3: TC
F4: DETAIL
F5:
F6: EXIT
F2: ERR LOG Displays an error log screen.
Sub-Item
F1: ERROR
F2: DATE
F3: TC
F4: DETAIL
F5:
F6: EXIT
–
–
Move the flashing
digit to the left or
right.
Saves the new
setting and exits
the pulldown
sequence preset
sub menu.
Exits the pulldown
sequence preset
sub menu without
saving the new
setting.
Alarm messages
Dates and times when
the alarms occurred
Positions where alarms
occurred (timecode)
Alarm details
–
Exits the alarm log
screen sub menu.
Error messages
Dates and times when
the errors occurred
Positions where errors
occurred (timecode)
Error details
–
Exits the error log screen
sub menu.