Jog/Shuttle Direction Indicators; Var/Jog Button; Shuttle/Jog Dial; Shuttle/Jog/Variable Operation Section - Sony PDW-HR1 Operation Manual

c CHROMA switch and adjustment knob
Set the chroma signal output levels for HD and SD output.
PRE: Regardless of manual settings, set the chroma signal
output levels to the standard levels.
VAR: Adjust the chroma signal output levels within the
range – ∞ to +3 dB by turning the adjustment knob.
d HUE/CHROMA-PHASE switch and adjustment
knob
Set the chroma phase.
PRE: Regardless of manual settings, set the chroma phase
to the standard value.
VAR: Adjust the chroma phase within the range ±30º by
turning the adjustment knob.
e SETUP/BLACK switch and adjustment knob
Set the setup and black levels for HD and SD output.
PRE: Regardless of manual settings, set the setup and
black levels to the standard levels.
VAR: Adjust the setup and black levels within the
following ranges by turning the adjustment knob.
• Setup level (59.94i/59.94P/29.97P mode): ±30 IRE
• Black level (50i/50P/25P mode): ±210 mV

8 Shuttle/jog/variable operation section

1 JOG indicator

2SHUTTLE/JOG button

a JOG indicator
Lights in green when the shuttle/jog dial is in jog mode.
b SHUTTLE/JOG button
Press this button, turning it on, to perform shuttle or jog
playback with the shuttle/jog dial.
When pressed during recording, this button stops
recording and selects shuttle/jog mode. If you do not want
22
Control Panel
3 Jog/shuttle direction
indicators

4 VAR/JOG button

5 Shuttle/jog dial

recording to stop when this button is pressed, set setup
menu item 145 MODE KEY ENABLE DURING
RECORDING to "stop & pause".
c Jog/shuttle direction indicators
These show the playback direction in jog, shuttle, or
variable speed mode.
b (green): Lights during playback in the reverse direction.
B (green): Lights during playback in the forward direction.
x (red): Lights during still image display.
d VAR/JOG button
Press this button, turning it on, to perform variable or jog
playback with the shuttle/jog dial. When pressed during
recording, this button stops recording and selects variable/
jog mode.
If you do not want recording to stop when this button is
pressed, set setup menu item 145 MODE KEY ENABLE
DURING RECORDING to "stop & pause".
e Shuttle/jog dial
The dial switches between shuttle/variable mode and jog
mode each time that you press it all the way in.
Shuttle/variable mode: The dial is in the raised position.
Jog mode: The dial is in the depressed position (the JOG
indicator is lit).
Turn the dial to the right to play in the forward direction,
and turn it to the left to play in the reverse direction.
• In jog mode, the playback speed varies from –1 to +1
times normal speed, according to the rotation speed of
the dial. There are no detents.
• In shuttle mode, the playback speed varies in the range
±20 times normal speed, according to the angular
position of the dial. There is a detent at the center
position, for still image playback.
• In variable mode, you can make fine adjustments to the
playback speed over the range from –1 to +1 times
normal speed, according to the angular position of the
dial. There is a detent at the center position, for still
image playback.
Regardless of the playback mode, you will normally press
the SHUTTLE/JOG or VAR/JOG button before turning
the dial. But it is also possible to put the unit into shuttle,
jog, or variable mode simply by turning the dial (by setting
setup menu item 101 SELECTION FOR SEARCH DIAL
ENABLE to "dial".)
Note
If you do set the above item to "dial", then you should
return the shuttle/jog dial to the center position after
conducting shuttle or variable playback. If you do not
return the dial to the center position, playback in shuttle or
variable mode can start because of vibrations during other
operations.