D-Link DGS-3612G - xStack Switch Reference Manual page 23

SNMP Status
RMON Status
Link Aggregation
Algorithm
Switch 802.1X
Auth Protocol
802.1X Authen
Network RADIUS
Forward EAPOL
PDU
HOL Prevention
Jumbo Frame
Syslog State
Broadcast Ping
Reply State
ARP Aging Time (0-
65535)
DVMRP State
PIM State
BGP State
OSPF State
OSPFv3 State
DNS Resolver State
®
xStack DGS-3600 Series Layer 3 Managed Gigabit Ethernet Switch
Use this pull-down menu to enable or disable Simple Network Management Protocol (SNMP)
on the Switch.
Remote monitoring (RMON) of the Switch is Enabled or Disabled here.
The algorithm that the Switch uses to balance the load across the ports that make up the port
trunk group is defined by this definition. Choose MAC Source, MAC Destination, MAC Src &
Dest, IP Source, IP Destination or IP Src & Dest (See the Link Aggregation section of this
manual).
MAC Address may enable by port or the Switch's 802.1X function; the default is Disabled.
This field must be enabled to view and configure certain windows for 802.1X.
Port-Based 802.1X specifies that ports configured for 802.1X are initialized based on the port
number only and are subject to any authorization parameters configured.
MAC-based Authorization specifies that ports configured for 802.1X are initialized based on
the port number and the MAC address of the computer being authorized and are then subject
to any authorization parameters configured.
The 802.1X authentication protocol on the Switch is set to RADIUS EAP and can be
configured to Local.
Enables or disables 802.1X Authentication Network RADIUS. The default is Enabled.
Enables or disables Forward EAPOL PDU. The default is Disabled.
If this option is enabled it prevents the forwarding of data to a port that is blocked. Traffic that
would normally be sent to the buffer memory of the Switch's TX queue is dropped so that
memory usage is conserved and performance across all ports remains high.
This field will enable or disable the Jumbo Frame function on the Switch. The default is
Disabled. When enabled, jumbo frames (frames larger than the Ethernet frame size of 1536
bytes) of up to 9216 bytes (tagged) can be transmitted by the Switch.
Enables or disables Syslog State. The default is Disabled.
Enables or disables the Broadcast Ping Reply State. The default is Enabled.
The user may globally set the maximum amount of time, in minutes, that an Address
Resolution Protocol (ARP) entry can remain in the Switch's ARP table, without being
accessed, before it is dropped from the table. The value may be set in the range of 0 to 65535
minutes with a default setting of 20 minutes.
The user may globally enable or disable the Distance Vector Multicast Routing Protocol
(DVMRP) function by using the DVMRP Global Settings window (L3 Features > IP
Multicast Routing Protocol > DVMRP Global Settings or click
The user may globally enable or disable the Protocol Independent Multicast - Dense Mode
(PIM-DM) function by using the PIM Global Settings window (L3 Features > IP Multicast
Routing Protocol > PIM > PIM Global Settings or click
The user may configure Border Gateway Protocol (BGP) by using the BGP State Settings
window (L3 Features > BGP > BGP Global Settings or click
The user may globally enable or disable the Open Shortest Path First (OSPF) function by
using the OSPF Global Settings window (L3 Features > OSPF > OSPF Global Settings or
click Detail Settings).
The user may globally enable or disable the Open Shortest Path First (OSPF) version 3
function by using the OSPFv3 Global Settings window (L3 Features > OSPF > OSPFv3 >
OSPFv3 Global Settings or click
The user may globally enable or disable the Domain Name Server Resolver function by using
the DNS Resolver Global Settings window (L3 Features > DNS Resolver > DNS Resolver
Global Settings or click
Detail Settings).
Detail Settings).
7
Detail Settings).
Detail Settings).
Detail Settings).