Sony PCS-G50 System Integration Manual page 67

To Be Registered in Network Camera List
Item Description
Name Enter a name of up to 38 characters to be displayed in the network camera list. Any characters can be
used without restriction.
IP Address Enter an IP address of a target network camera.
User Name Required when "Admission" is set to On. Enter a user name of 5 to 16 1-byte alphanumeric characters.
The user name entered here shall be the same as the one configured on the network camera itself with
your desired authority
Password Required when "Admission" is set to On.
The password entered here shall be the same as that configured for the desired user on the network
camera itself.
HTTP Port Number Enter an HTTP port number of a target network camera.
Admission Specify whether or not a user is authenticated when connecting to a network camera.
m
. Normally set to "Admission" to On. When set to On, be sure to also enter "User Name" as explained
above.
. When set to Off, with the network camera, set "Viewer authentication" under the User Menu to Off
and select the viewer mode to be enabled without authentication.
. The relationship between this "Admission" and camera's "Viewer authentication" is shown in the
footnote
Transmission Select the transmission mode to be used when connecting a network camera, from "TCP", "UDP
(Unicast)" and "UDP(Multicast)".
m
. The recommended mode is "UDP(Unicast)"
. When UDP(Unicast) transmission is selected while connecting the camera with User authority, be
sure to perform unicast streaming setting so that video and audio port numbers do not overlap with the
main PCS-G50/G70's and also do not overlap with other network cameras' which are connected with
the main PCS-G50/G70.
. When UDP (Multicast) transmission is selected while connecting the camera with User authority, be sure
to set "Multicast streaming" under the Streaming tab in the Camera Menu of the network camera to On.
*1: When "Admission" is set to "On" and "Password" is left blank, users are asked for the password every time dialing.
This enables you to restrict users to access to individual network camera.
*2:
Admission Viewer authentication
(On PCS) (On Network camera)
On On
On Off
Off Off
Off On
PCS-G70/G70P/G50/G50P
*1
*2
.
Description
Normally set both to On. You are authenticated every time dialing to connect to the network camera.
Only when the user name and password stored in the network camera list match those stored in the
User menu of the network camera at dialing (If the password in the network camera list is left blank, you
are asked for the password when dialing.), the video communication terminal can connect the camera
with the corresponding authority. If the administrator name and password are stored in the network
camera list, the video communication terminal can connect the camera with the administrator authority.
The settings of Admission = On and Viewer authentication = Off are not recommended although
connection can be made.
n
You are authenticated when dialing to connect to the network camera.
When the user name and password stored in the network camera list match those stored in the User
menu of the network camera at dialing and (If the password in the network camera list is left blank,
you are asked for the password when dialing.), the video communication terminal can connect the
camera with the corresponding authority, In the case of connection with user authority (not administra-
tor), however, the video communication terminal cannot receive audio from the camera.
When the user name and password stored in the network camera list do NOT match those stored in
the User menu, the video communication terminal can connect the camera without authentication. In
this case, the viewer mode selected under Viewer authentication = Off is enabled, and functions
corresponding to the selected viewer mode can be used. (See Table 1 in section 1-11-2.)
Set both to Off when you want to connect to network cameras without authentication. Note that the
video communication terminal cannot always receive audio from the network camera without
authentication.
Connection cannot be made.
Change to any of the above-mentioned.
Enter a password of 5 to 16 1-byte alphanumeric characters.
Default
Blank
Blank
Blank
Blank
80
*1
On
TCP
1-63