Sony PCS-G50 System Integration Manual page 101

For loading of application
1. Display the Service menu.
2. Insert the Memory Stick, in which the application
software of the version to be loaded is recorded, into
the Memory Stick slot.
3. Select "Load Application" using , ,
buttons on the remote commander and press the PUSH
ENTER button.
4. A confirmation message on whether to execute is
displayed.
5. To execute, select "OK" and press the PUSH ENTER
button. The screen display during loader execution
then appears. After completion, the launcher menu is
displayed. To cancel execution, select "Cancel" and
press the PUSH ENTER button. The current display
returns to the Service menu.
6. Push in the Memory Stick once and take out it.
n
Do not turn off the power or take out a Memory Stick until
the launcher menu is displayed.
For command input
1. Display the Service menu.
2. Select "Command" using , ,
remote commander and press the PUSH ENTER
button.
A key guidance is then displayed.
3. Enter the commands in a command list from the
remote commander.
m
. To set two or more commands, put a one-character
blank between the commands and then enter them.
. The validated command can be confirmed in a
command column at all times.
. Use only the commands in the command table. If
any other command (a free character string) is
entered, the internal operation mode may become an
improper state.
4. Select "Save" using , ,
remote commander and press the PUSH ENTER
button.
A Setup menu is then displayed.
To stop setting
Select "Cancel" using , ,
commander and press the PUSH ENTER button, or press
the RETURN button on the remote commander.
PCS-G70/G70P/G50/G50P
and
and buttons on the
and buttons on the
and buttons on the remote
Service menu function list
Command:
The commands listed in the table below are those for
changing the internal operation mode of the communication
terminal when the system is used in a special environment.
Command Description
SMS Validates an SMS function.
KV66 For KV-29FX66E monitors.
Sets the input selection to 3 after power on
when a KV-29FX66E monitor is being used.
An IR output is changed so that the command
during power-off sequence is sent properly. The
monitor mode setting is invalidated when this
command is specified, but the mode setting
becomes valid by deleting this command.
WBxxxXyyy Adjusts the angle of view of the whiteboard
used.
YCLP** (** indicates any of the values of 80, 90, A0,
B0, C0, D0, or E0.)
Clipped to the value for which the luminance
value of a menu screen was specified. The
section that has luminance exceeding the
specified value is clipped to the specified value.
YLVL** (** indicates a decimal value of 0 < ** < 80.)
Shifted downward proportionally to the value for
which the luminance value of a menu screen was
specified. The whole screen becomes dark as the
value increases. The black tone cannot be
reproduced because all values are shifted.
D2B Sets ISDN (2B) to the default value using the
dial menu.
BMR0 AVAYA Bonding Mode Revision 0
PROJ Sends the remote control code for the
projector.
POFF Does not display the packet loss indicator.
E1PRI Changes forcibly to E1
(Default is T1 in NTSC models)
T1PRI Changes forcibly to T1
(Default is E1 in PAL models)
PDx Performs parallel dialing in units of xB (0-29)
(default: in units of 5B).
When 0 is entered, sets the default value 5B.
When 30 or more is entered, sets the default
value 29B.
(Examples: PD1, PD29)
GKDISP An alias name is displayed in a launcher menu
instead of an IP address.
NOCIPN CallingPartyNumber (originator number
information) is not added to a SET_UP
message during ISDN call origination.
NOSC SendingComplete is not added to a SET_UP
message during ISDN call origination.
SNDCMP SendingComplete is added to a SET_UP
message during ISDN call origination.
PKS**** Changes the video packet size. (**** = to 99)
TCB A frame is displayed on the screen when a
moving body is detected in the presenter mode
of a tracking camera (PCSA-CTG70/CTG70P).
2-17