Download
Share
Print this page
KidKraft RIDGEMOOR PERCH SWING SET Manual
  1. Manuals
  2. Brands
  3. KidKraft Manuals
  4. Play Sets & Playground Equipment
  5. RIDGEMOOR PERCH SWING SET
  6. Manual
KidKraft RIDGEMOOR PERCH SWING SET Manual

KidKraft RIDGEMOOR PERCH SWING SET Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
RIDGEMOOR
PERCH SWING SET
OBSTACLE FREE SAFETY ZONE - 29' 6 3/8" L x 24' 3 3/8" D x 16' 5 1/2" H (9m x 7.4m x 5m) area requires Protective
Surfacing. See Page 4.
MAXIMUM VERTICAL FALL HEIGHT - 7' 5/16"(2.23m)
CAPACITY - 10 Users Maximum, Ages 3 to 10; Weight Limit 110 lbs. (50 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools, churches, nurseries, day cares or parks.
INSTALLATION AND OPERATING INSTRUCTIONS
FOR 24/7 ONLINE PARTS REPLACEMENT
parts.kidkraft.com
KidKraft, Inc.
4630 Olin Road
Dallas, Texas 75244
USA
customerservice@kidkraft.com
1.800.933.0771
972.385.0100
parts.kidkraft.eu
KidKraft Netherlands BV
Olympisch Stadion 8
1076 DE Amsterdam
The Netherlands
europecustomerservice@kidkraft.com
+31 20 305 8620
M-F from 09:00 to 17:30 (GMT+1)
29' 6 3/8"
16' 3 1/4"
4.96 m
24' 3 3/8"
7.4 m
9409735
Rev 07/11/2023
TWO-PERSON
ASSEMBLY TIME
ASSEMBLY
12 - 18 HOURS
WARNING
To reduce the risk of serious injury or death, please read and follow
these instructions. Keep and refer to instructions as needed and
pass along to any future owners of this item.
9 m
11' 1 5/8"
3.4 m
9' 11 1/2"
3.04 m
WARNING. ONLY
FOR OUTDOOR
DOMESTIC USE

Advertisement

loading

Related Manuals for KidKraft RIDGEMOOR PERCH SWING SET

Summary of Contents for KidKraft RIDGEMOOR PERCH SWING SET

  • Page 1 9' 11 1/2” 3.04 m INSTALLATION AND OPERATING INSTRUCTIONS FOR 24/7 ONLINE PARTS REPLACEMENT 9409735 Rev 07/11/2023 parts.kidkraft.com parts.kidkraft.eu KidKraft, Inc. KidKraft Netherlands BV 4630 Olin Road Olympisch Stadion 8 TWO-PERSON ASSEMBLY TIME WARNING. ONLY FOR OUTDOOR ASSEMBLY 12 - 18 HOURS...
  • Page 2 Congratulations on purchasing a KidKraft product! Our items are made of high-quality, durable Cunninghamia Lanceolata wood from the cypress family. Lumber from these trees are known for their light weight and excellent strength. The porosity of this wood allows the moisture to absorb and evaporate in the fibers, resisting rot and bugs.
  • Page 3 Warnings and Safe Play Instructions CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using this play system.
  • Page 4 Protective Surfacing - Reducing Risk of Serious Head Injury From Falls One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable for the equipment height in accordance with ASTM F1292.
  • Page 5 Instructions for Proper Maintenance Your KidKraft Play System is designed and constructed of quality materials with your child’s safety in mind. As with all outdoor products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your Play Set, it is important that you, the owner, properly maintain it.
  • Page 6 About Our Wood KidKraft Premium Play Systems uses only premium playset lumber, ensuring the safest product for your children’s use. Although we take great care in selecting the best quality lumber available, wood is still a product of nature and susceptible to weathering which can change the appearance of your set.
  • Page 7 KidKraft Limited Warranty MISSING OR DAMAGED PARTS: KidKraft will replace any parts within 90 days from date of purchase found to be missing from or damaged in the original packaging. See Fig.1 Fig. 1 Product Age (All Parts) Consumer Pays...
  • Page 8 Keys to Assembly Success Tools Required • Tape Measure • #1 Phillips, #2 Robertson • Open End Wrench • 3/16” Hex Key • Carpenters Level and Screwdriver (1/2” & 9/16”) • 8’ Step Ladder • Carpenters Square • Ratchet with extension •...
  • Page 9 (9320374) 2x - Rock A - Green (9320195) 1x - Rock A - Yellow (9320196) 4x - Jamb Mount (9206300) 1x - KidKraft Logo Plaque (3320353) 1x - Rock B - Green (9320295) 1x - Rock B - Yellow (9320296)
  • Page 10 Part Identification - Box 1 (1) 2686 - Counter Front 5/8 x 2-3/4 x 40-5/8" 3632686 15.9 x 69.9 x 1031.9 mm 5 - Counter Side 5/8 x 2 x 6-3/4" 38045536 15.9 x 50.8 x 171.5mm (2) 2716 - Counter Mid Top 1 x 4 x 17-5/8" 3632716 15.9 x 85.7 x 447.7 mm 61 - 1 x 2 x 12-9/16"...
  • Page 11 Hardware (Actual Size) Wafer Bolt 5/16 x 1" 2pc. WB1 - Wafer Bolt 5/16 x 3" (8 x 76mm) - (53613310) 3pc. WB7 - - (53613330) (8 x 25mm) Hex Bolt 1/4 x 1-1/4" 24pc. H9 - - (53703211) 1/4 x 2-1/2" (6 x 32mm) 16pc.
  • Page 12 Hardware (Actual Size) 32pc. TN1 - 1/4" (6mm) T - Nut 5pc. FW0 - 3/16" (5mm) Flat Washer - (54503200) (51103100) 5pc. LW2 - 5/16" (8mm) Lock Washer - (51303300) 42pc. FW1 - 1/4"(6mm) Flat Washer - 10pc. TN2 - 5/16" (8mm) T- Nut (51103200) (54503300) 37pc.
  • Page 13 on - Box 2 ID#2 - F25890 06-06-2016 15.9 x 133.4 x 482.6 mm 15.9 x 133.4 x 482.6 mm 15.9 x 133.4 x 482.6 mm 23.8 x 82.6 x 362 mm 23.8 x 82.6 x 1181.1mm...
  • Page 14 Part Identification - Box 3 ID#2 - F25890 06-06-2016 (1) 2715 - 5/4 x 3 x 10" - Door Stop (1) 2718 (4) 2 60 Roof Support 1¼ x 2¼ x 37½" 3632760 （25.4 x 63.5 x 254 mm） 3632715 Door Window Panel 31.8 x 57.2 x 952.5mm 1¼...
  • Page 15 Part Identification (Reduced Part Size) 1x - TNR 3 Tube Support (9203601) 9x - TNR 2 Slide Elbow (3310121) 1x - TNR 2 Slide Exit Top (3310124) 10x - TNR 4 Clamp Ring (9300130) (Green) 1x - TNR 4 Post Mount Set - (3200155) 1x - TNR3 Short Exit (33101 32) 31x - Square Nylok Nut...
  • Page 16 Hardware (Actual Size) 1/4 x 3/4" - Pan Bolt (6 x 19mm) (53453203) (1) Wafer Lag Screw 1/4 x 2-1/2" (52613222) (6 x 64mm) 1/4 x 1" - Pan Bolt (6 x 25mm) (53413210) - Quadrex Driver Bit (9200015) 1 x S37 - #7 x 5/8" - 52433009 15.9mm 1/4 x 4¼"...
  • Page 17 Part Identification (Reduced Part Size) 2pc. - 11368 - Crow Nest Post A 1 1/4" x 3" x 9 3/8"(31.8 x 76.2 x 238.2mm) 36311368 2pc. - 11184 - Crow Nest Floor Support 1 1/2" x 1 1/2" x 22 5/8"(38.1 x 38.1 x 575.4mm) 36311184 2pc.
  • Page 18 Part Identification (Reduced Part Size) 1pc. - 11371 - Platform Bottom 1 1/4" x 3 1/2" x 12 3/16"(31.8 x 88.9 x 310mm) 36311371 1pc. - 11372 - Platform Top 1 1/4" x 3 1/2" x 13 3/8"(31.8 x 88.9 x 340mm) 36311372 2pc.
  • Page 19 Part Identification (Reduced Part Size) 1pc. - 9481 - SW Side Panel 1 3/8" x 14 1/8" x 38 13/16" (34.3 x 358.8 x 985.6mm) 37639481 4x - Swing Bracket (9201530) 2x - MOD 5 Pane Side Lite (9330505) 2x - Hand Grip (9320040) Hardware Identification (Actual Size) 32pc.
  • Page 20 Hardware Identification (Actual Size) 4pc. H10 - Hex Bolt 1/4 x 2-1/4" - (53703221) 6pc. H11 - Hex Bolt 1/4 x 2-3/4" - (53703223) (6.4 x 57.2mm) (6.4 x 69.9mm) 22pc. G27 - Hex Bolt 5/16 x 1-3/4"- (53703313) (7.9 x 44.5mm) 4pc.
  • Page 21 Inventory Parts - Read This Before Starting Assembly STOP STOP STOP STOP Inventory should be completed before starting installation. KidKraft will not cover costs of any additional installation trip due to missing or damaged pieces. This is the time for you to inventory all your hardware, wood and accessories, referencing the parts identification sheets.
  • Page 22 Step 1: Front and Back Wall Prep Part 1 It is important to assemble the frame on a flat, smooth surface. A: Place (2771) End Post and (2770) End Post Left side by side with the grooves facing up and in. Put (2770) End Post Left on the right hand side.
  • Page 23 Step 1: Front and Back Wall Prep Part 2 It is important to assemble the frame on a flat, smooth surface. D: Turn the assembly over, place (2774) Upright in the middle groves of (2775) Panel Cross Support and (2772) Panel Floor Support then attach all boards with 8 (H9) Hex Bolts (with lock washer and flat washer) connecting to the previously installed t-nuts.
  • Page 24 Step 2: End Wall Prep Part 1 It is important to assemble the frame on a flat, smooth surface. A: Place (2768) Panel Floor and 2 (2769) Panel BT Frames on a hard, flat surface with the long side up. Tap in 2 (TN1) T-nuts per board.
  • Page 25 Step 2: End Wall Prep Part 2 It is important to assemble the frame on a flat, smooth surface. D: Turn the assembly over then attach all boards with 6 (H9) Hex Bolts (with lock washer and flat washer) connecting to the previously installed t-nuts. (fig. 2.3 and 2.4) Fig.
  • Page 26 Step 3: Swing Wall Prep Part 1 It is important to assemble the frame on a flat, smooth surface. A: Place (2757) LT Post Assembly and (2758) RT Post Assembly on a hard, flat surface with the notches facing down. The top of the post assemblies have the longer notches. (fig. 3.1) B: Tap 1 (TN2) T-nut in the top holes and 1 (TN1) T-nut in the middle and bottom holes.
  • Page 27 Step 3: Swing Wall Prep Part 2 It is important to assemble the frame on a flat, smooth surface. C: Turn the (2757) LT Post Assembly and (2758) RT Post Assembly over and place 2 (2756) Siding Assemblies on top so one sits flush with the top of the middle groove and the second fits flush with the top of the bottom groove.
  • Page 28 Step 3: Swing Wall Prep Part 3 It is important to assemble the frame on a flat, smooth surface. E: Attach (2630) SW Top to (2757) LT Post Assembly and (2758) RT Post Assembly with 2 (WB1) Wafer Bolts (with flat washer) connecting to previously installed t-nuts. (fig. 3.5 and 3.6) F: Attach (2768) Panel Floor to (2757) LT Post Assembly and (2758) RT Post Assembly with 2 (H9) Hex Bolts (with lock washer and flat washer) connecting to previously installed t-nuts.
  • Page 29 Step 3: Swing Wall Prep Part 4 It is important to assemble the frame on a flat, smooth surface. I: Attach the top board in each (2756) Siding Assembly to (2757) LT Post Assembly and (2758) RT Post Assembly with 4 (S30) Wood Screws per board. (fig. 3.8 and 3.9) J: Attach the remaining boards in each (2756) Siding Assembly to (2757) LT Post Assembly and (2758) RT Post Assembly with 2 (S0) Truss Screws per board.
  • Page 30 Step 4: Frame Assembly Part 1 It is important to assemble the frame on a flat, smooth surface. A: Place Swing Wall from Step 3 between 2 Front and Back Walls from Step 1, noticing the wall orientations. The tops and bottoms of the walls should be flush. Make sure the walls are square then using the pilot holes as a guide pre-drill with a 1/8”...
  • Page 31 Step 4: Frame Assembly Part 2 B: Place End Wall from Step 2 between the Front Wall and Back Wall noticing the wall orientation. The tops and bottoms of the walls should be flush. Make sure the walls are square then using the pilot holes as a guide pre- drill with a 1/8”...
  • Page 32 Step 4: Frame Assembly Part 3 C: Loosely attach 1 (2607) Diagonal to left (2778) SW Ground MOD with 1 (H10) Hex Bolt (with lock washer, flat washer and t-nut). (fig. 4.5) D: Place each (2607) Diagonal tight and flush to the front of the Swing Wall then pre-drill pilot holes with a 1/8” (3.2 mm) drill bit and attach each (2607) Diagonal to the Swing Wall with 1 (LS3) Lag Screw (with flat washer) per board, checking that they remain flush to outside edge.
  • Page 33 Step 5: Floor Assembly Part 1 A: From inside of the assembly centre (2608) Floor Joist over the pilot holes in both (2768) Panel Floors in the Swing and End Walls, measure 5/8” (15.9 mm) down from the top of boards then attach (2608) Floor Joist to each board using the left and centre holes with 2 (S4) Wood Screws per board.
  • Page 34 Step 5: Floor Assembly Part 2 B: On the inside of both the Front and Back Walls loosely attach 1 (2777) Side Joist MOD to each (2772) Panel Floor Support with 2 (H11) Hex Bolts (with lock washer, flat washer and t-nut) as shown in fig. 5.5. Make sure both (2777) Side Joist MODs are level with (2608) Floor Joist.
  • Page 35 Step 5: Floor Assembly Part 3 C: Fasten each (2777) Side Joist MOD to each (2772) Panel Floor Support with 4 (S3) Wood Screws per board as shown in fig. 5.6. D: Tighten all (H11) Hex Bolts in both (2777) Side Joist MOD. Fig.
  • Page 36 Step 5: Floor Assembly Part 4 E: Starting at the Swing Wall place (2648) Floor Board followed by 8 (2609) Floor Boards. Make sure all boards are evenly spaced then attach to (2608) Floor Joist and each (2777) Side Joist MOD with 5 (S20) Wood Screws per board.
  • Page 37 5/16” Flat Washer Hardware Other Parts Wood Parts 12 x Hex Bolt (5/16” flat washer x 2, 5/16” lock nut) 6 x Swing Hangers Engineered Beam 4 x 6 x 88” 2614 2 x Hex Bolt (5/16” flat washer x 2, 5/16” lock nut) 2 x L-Beam Bracket 1 x Wafer Bolt (5/16” flat washer, 5/16” t-nut) 1 x KidKraft Logo Plaque #6 x 1” Wood Screw...
  • Page 38 Step 7: Swing End Assembly A: Loosely attach 2 (2613) Heavy SW Posts to (2615) SW Upright using 2 (G7) Hex Bolts (with lock washer, flat washer and t-nut). Notice 2 bolt holes at top of (2615) SW Upright and orientation of angle. (fig. 7.1) B: Attach (2616) SW Support to both (2613) Heavy SW Posts and (2615) SW Upright using 3 (G4) Hex Bolts (with lock washer, flat washer and t-nut).
  • Page 39 Step 8: Attach Swing End to Swing Beam A: Place Swing End Assembly against Swing Beam Assembly then place 1 Beam Bracket on each side of the assembly (they are specific for left and right side) and attach with 5 (G21) Hex Bolts (with 2 flat washers and 1 lock nut).
  • Page 40 Step 9: Attach Swing Assembly To Fort A: Place Swing Assembly against top of (2630) SW Top, make sure assembly is level then attach from inside the fort assembly into each L-Beam Bracket with 4 (G8) Hex Bolts (with 2 flat washers and 1 lock nut). (fig. 9.1) L-Beam 2630...
  • Page 41 Step 10: Install Ground Stakes MOVE FORT TO FINAL LOCATION PRIOR TO STAKING FINAL LOCATION MUST BE LEVEL GROUND A: In the 5 places shown in fig. 10.1 drive the Rebar Ground Stakes 13” (330 mm) into the ground against outside front corner of the End Wall, on both (2607) Diagonals and both (2613) Heavy SW Posts.
  • Page 42 Step 11: Install Upper and Lower Jambs Part 1 A: Install the (2601) Lower Jamb on the Front Wall using 2 Jamb Mounts and 8 (S0) Truss Screws. (fig. 11.1, 11.2 and 11.3) Make sure grooves of (2601) Lower Jamb facing inside Fig. 11.1 Fig. 11.2 Outside View Jamb Mount x 4 per...
  • Page 43 Step 11: Install Upper and Lower Jambs Part 2 B: Install the (2601) Lower Jamb on the Back Wall using 2 Jamb Mounts and 8 (S0) Truss Screws. (fig. 11.4, 11.5 and 11.6) Make sure grooves of (2601) Lower Jamb facing inside Fig. 11.5 Outside View Fig. 11.4 Jamb Mount x 4 per...
  • Page 44 Step 11: Install Upper and Lower Jambs Part 3 C: Install the (2602) Upper Jamb on the End Wall using 2 Jamb Mounts and 8 (S0) Truss Screws per board. (fig. 11.7, 11.8 and 11.9) Make sure grooves of (2602) Upper Jamb facing inside Fig. 11.8 Fig. 11.7 Notice orientation of this bracket.
  • Page 45 Step 12: Install Windows Part 1 A: Install the (2719) Upper Window Insert on the Front Wall with 9 (S0) Truss Screws. (fig. 12.1 and 12.2) Fig. 12.2 Fig. 12.1 Front Wall 2719 2719 Inside View Tight Wood Parts Hardware Upper Window Insert Truss Screw 2719...
  • Page 46 Step 12: Install Windows Part 2 B: Install the (2719) Upper Window Insert on the Back Wall with 9 (S0) Truss Screws. (fig. 12.3 and 12.4) Fig. 12.4 Fig. 12.3 Back Wall 2719 2719 Inside View Tight Wood Parts Hardware Upper Window Insert Truss Screw 2719...
  • Page 47 Step 12: Install Windows Part 3 C: Install the (2720) Lower Window Insert on the Back Wall with 9 (S0) Truss Screws. (fig. 12.5 and 12.6) Fig. 12.6 Fig. 12.5 2720 2720 Inside View Tight Back Wall Wood Parts Hardware Lower Window Insert Truss Screw 2720...
  • Page 48 Step 12: Install Windows Part 4 D: Install the (2720) Lower Window Insert on the Front Wall with 9 (S0) Truss Screws. (fig. 12.7 and 12.8) Fig. 12.8 Fig. 12.7 2720 2720 Front Wall Inside View Tight Wood Parts Hardware Lower Window Insert Truss Screw 2720...
  • Page 49 Step 13: Install Wall Inserts Part 1 A: Install the (2665) Half Wall Insert on the End Wall with 4 (S0) Truss Screws. (fig. 13.1 and 13.2) Fig. 13.1 2665 End Wall Fig. 13.2 Inside View 2665 Tight Wood Parts Hardware Half Wall Insert Truss Screw...
  • Page 50 Step 13: Install Wall Inserts Part 2 B: Install the (649A) Short Half Wall on the Back Wall with 4 (S0) Truss Screws. (fig. 13.3 and 13.4) Fig. 13.4 Fig. 13.3 Back Wall Inside View Back Wall 649A 649A Tight Wood Parts Hardware Short Half Wall...
  • Page 51 Step 14: Rock Wall Assembly Fig. 14.1 Note: The holes in the rock boards 2776 must orient to the 2780 2780 2781 top of the boards. 2781 2781 2779 7-5/8” (193.6 mm) x 4 per Approx board Note: Gaps between boards 2-1/4” (57 mm), not to exceed 2-3/8”...
  • Page 52 Step 15: Attach Rock Wall Assembly to Fort Part 1 A: Place Rock Wall Assembly centred in opening of the Back Wall as shown in the Fort Guide and flush as shown below. Attach (2776) Rock Rails to the Back Wall using 4 (S11) Wood Screws. (fig. 15.1 and 15.2) B: Attach 1 (2779) Access Board to top of Rock Wall Assembly, flush to top of (2776) Rock Rails using 4 (S20) Wood Screws.
  • Page 53 Step 15: Attach Rock Wall Assembly to Fort Part 2 C: Drive 1 Rebar Ground Stake 13” (330 mm) into the ground against outside (2776) Rock Rail then attach with 1 (S7) Pan Screw. Be careful not to hit the washer while hammering stake into the ground as this could cause the washer to break off.
  • Page 54 Step 16: Attach Door Components Part 1 A: On the inside of (2718) Door Window Panel measure 15” up from the bottom and attach Catch Plate flush to the edge using 2 (S18) Wood Screws. (fig. 16.1) B: On the inside of (2718) Door Window Panel measure 22” up from the bottom and attach 1 Door Handle using 2 (S13) Pan Screws.
  • Page 55 Step 16: Attach Door Components Part 2 C: On the outside of the (2718) Door Window Panel attach the second Door Handle at approximately the same place as the one on the inside. Use 2 (S13) Pan Screws. (fig. 16.2) D: On the opposite side of the Door Handle measure 5/8”...
  • Page 56 Step 17: Attach Door Assembly to Fort A: In the opening for the door on the Front Wall as shown in the Fort Guide, measure 5/8” up from (2769) Panel BT Frame and maximum 5/8” from (2601) Lower Jamb and attach the remaining side of the hinges to (2601) Lower Jamb using 3 (S13) Pan Screws per hinge.
  • Page 57 Step 18: Attach Door Stop A: In the notched out opening of (2715) Door Stop attach the Magnetic Catch using 2 (S18) Wood Screws. (fig. 18.1) Important: Use a hand held screw driver and DO NOT over tighten. B: On the inside of the assembly, attach (2715) Door Stop to the panel with 3 (S11) Wood Screws, making sure (2715) Door Stop overhangs the panel by 1-1/4”...
  • Page 58 Step 19: Attach Slide to Fort A: Place Slide in the centre of the opening at the front of the fort as shown in the Fort Guide, pre-drill with a 1/8” (3.2 mm) drill bit then attach slide to fort through the (2772) Panel Floor Support using 3 (S7) Pan Screws. (fig. 19.1, 19.2 and 19.3) Fig.
  • Page 59 Step 20: Attach Slide Wall Inserts A: In the narrow opening of the End Wall (Upper Jamb should already be installed), place the MOD Side Lite from inside the assembly then attach to the wall and (2602) Upper Jamb with 14 (S0) Truss Screws. (fig. 20.1 and 20.2) B: In the wider opening of the End Wall tight to (2768) Panel Floor place (8935) Lower SL Insert from inside the assembly then attach to the wall and (2602) Upper Jamb with 4 (S0) Truss Screws.
  • Page 60 Step 21: Slide Section Assemblies Part 1 Note: When installing Pan Bolts make sure to look at holes so bolts go through the side with the round recess and the lock nuts go through the side with the hexagonal recess. (fig. 21.3) A: Fit 2 TNR2 Slide Elbows together and attach with 8 (PB1) Pan Bolts (with lock nut) as shown in fig.
  • Page 61 Step 21: Slide Section Assemblies Part 2 Note: When installing Pan Bolts make sure to look at holes so bolts go through the side with the round recess and the lock nuts go through the side with the hexagonal recess. (fig. 21.3) D: Attach TNR2 Slide Exit Top and the remaining TNR2 Slide Elbow together using 8 (PB1) Pan Bolts (with lock nut) as shown in fig.
  • Page 62 Step 22: Attach Flange Assembly to Fort Part 1 A: With a helper place the Flange Assembly flush to the top opening in End Wall as shown in fig. 22.1 and the Fort Guide, then pre-drill 1/8” pilot holes in (8935) Lower SL Insert for the 4 bottom mounting locations (approximate spots where circles are on figure), making sure the pre-drilled holes are a minimum of 1”...
  • Page 63 Step 22: Attach Flange Assembly to Fort Part 2 D: Place (8934) SL Gusset tight to (2768) Panel Floor, flush to the top of the bottom opening and attach to Flange Assembly with 2 (S6) Pan Screws. (fig. 22.4 and 22.5) E: Pre-drill pilot hole with a 1/8”...
  • Page 64 Step 23: Attach Elbow Assembly to Flange Assembly Note: Keep all bolts loose until further step. A: Fit one of the Elbow Assemblies to the Flange Assembly by lining up the arrows on each assembly. Attach Elbow Assembly to Flange Assembly using 6 ¼ x 12.7mm” Pan Bolts and Square Lock Nut. (Fig. 23.2 & 23.3). B: Attach one of the Elbow assemblies to another Elbow Assembly making sure to line up the arrows on each assembly.
  • Page 65 Step 24: Attach TNR3 Slide Exit to Exit Elbow Assembly A: Insert flange of Exit Elbow Assembly (slide elbow) into the slots on TNR3 Short Exit. (fig. 24.1) B: Rotate Slide Exit and use Quadrex Driver as a guide pin so the holes are aligned and attach with 5 (PB1) Pan Bolts (with lock nuts) starting with the bottom middle hole and working up each side.
  • Page 66 Step 25: Attach Exit End Assembly to Fort A: Fit the Exit End Assembly to the last Elbow Assembly by lining up the arrows on each assembly. Notice the elbow orientation. (fig. 25.1). Attach with 6 (¼ x 12.7 mm) Pan Bolts and Square Lock Nuts. (fig. 25.2) Fig.
  • Page 67 Step 26: Attach TNR 4 Clamp Rings A: Place 2 TNR4 Clamp Rings around each joint making sure to match the arrows with the end of the Clamp Ring as shown in (fig. 26.1 & 26.2 ). B: Connect TNR4 Clamp Rings in 2 spots using 1 (PB6) ¼ x 1” Pan Bolt (with lock nut) per side. (fig.26.3) Note: When installing Pan Bolts make sure to look at holes so bolts go through the side with the round recess and the lock nuts go through the side with the hexagonal recess.
  • Page 68 Step 27: TNR Brace Assembly A: Attach (8965) TNR Upright to (8963) TNR Ground Brace with 1 (H8) Hex Bolt (with lock washer, flat washer and t-nut) in the top hole. Make sure both boards are square then attach with 1 (S11) Wood Screw. (fig. 27.1) 8965 Fig.
  • Page 69 Step 28: Attach TNR 4 Slide to Adventure Tower A: Place TNR Brace Assembly against (2771) End Post Left so it sits under the slide. It is not attached yet. (fig. 28.1) B: On the fourth Elbow Assembly attached remove the pan bolt and nut which is facing the fort (installed in Step 23).
  • Page 70 Step 29: Attach TNR Brace Assembly and TNR4 Slide A: Remove (H9) Hex Bolt from bottom of (2771) End Post then attach (8963) TNR Ground Brace flush to the bottom of (2618) Front Back Panel with 2 (S11) Wood Screws and 1 (S4) Wood Screw. (fig. 29.1 and 29.3) B: Place 1 TNR4 Post Mount Clamp on either side of the Clamp Ring so that the bent tops clip in behind the Clamp Ring.
  • Page 71 Step 30: Attach Ground Stake to TNR Upright A: In the spot shown in fig. 30.1 drive 1 Rebar Ground Stake 13” (330 mm) into the ground against the (8965) TNR Upright. Be careful not to hit the washer while hammering stake into the ground as this could cause the washer to break off.
  • Page 72 Step 31: Counter Assembly Part 1 A: Flush to each end and to the top of (2687) Counter Back attach 1 (0457) Counter Joist per end with 1 (S20) Wood Screw per joist. Notice the remaining holes at the bottom of (2687) Counter Back. (fig. 31.1) B: Place the remaining 2 (0457) Counter Joists centred over the pilot holes in the middle of (2687) Counter Back and flush to the top of the board, then attach, in the top holes, with 1 (S20) Wood Screw per joist.
  • Page 73 Step 31: Counter Assembly Part 2 C: On the inside of the panel shown in the Fort Guide place Counter Assembly so the top of (2687) Counter Back is flush to the top of the opening then attach with 5 (S20) Wood Screws. (fig. 31.2 and 31.3) Fig.
  • Page 74 Step 31: Counter Assembly Part 3 D: Place 1 (0461) Counter Brace flush to the front and outside edge of each outer (0457) Counter Joist and tight to the panel then attach with 2 (S3) Wood Screws per brace. (fig. 31.4 and 31.5) Fig.
  • Page 75 Step 31: Counter Assembly Part 4 E: Place (2686) Counter Front against (0457) Counter Joists so the ends are flush and the centre (0457) Counter Joists are centred over the pilot holes. Measure 5/8” down from the top of (2686) Counter Front on both ends and attach to the (0457) Counter Joists with 4 (S20) Wood Screws.
  • Page 76 Step 31: Counter Assembly Part 5 F: Tight to (2687) Counter Back attach (2685) Counter Top to each (0457) Counter Joist with 4 (TS) Trim Screws. (fig. 31.7) G: Tight to (2685) Counter Top and flush to the outside edges of the outer (0457) Counter Joists attach 1 (0455) Counter Side per joist with 3 (TS) Trim Screws per board.
  • Page 77 Step 31: Counter Assembly Part 6 J: Place Faucet and 2 Sink Knobs in opening of Sink and attach Sink Knobs with included hardware. (fig. 31.9) Important: Use a hand held screw driver and DO NOT over tighten. Fig. 31.9 Faucet Sink Knob Sink Knob...
  • Page 78 Step 31: Counter Assembly Part 7 K: Place Sink and Stove in the openings of the Counter Assembly then attach 4 Mount Clips with included hardware to the bottom of the Sink and Stove to secure in place. (fig. 31.10 and 31.11) Important: Use a hand held screw driver and DO NOT over tighten.
  • Page 79 Step 32: Attach Utensil Shelf A: From inside the assembly, centred in the top of the opening of panel as shown in the Fort Guide, above the counter, attach Utensil Shelf with 2 (S13) Pan Screws as shown in fig. 32.1 and 32.2. B: Attach Pot, Pan and Spatula to the Utensil Shelf.
  • Page 80 Mailbox Halves Attach Halves here Fig. 16.1 Fig.33.1 Mailbox Door Included Hardware Insert tabs into slots here Mailbox Flag Included Hardware Mailbox Door is attached here Mailbox Mount Other Parts 1 x Mailbox (with included hardware) Instructional video: http://www.kidkraft.eu/stoneycreek-assembly europecustomerservice@kiddraft.com...
  • Page 81 Step 33: Attach Mailbox Part 2 E: On the outside corner of the Door Wall as shown in fig. 33.2 place Mail Box Assembly on the panel then attach with 1 (S10) #8 x 1” Pan Screw from the bottom and 2 (S10) #8 x 1” Pan Screws on the top. (fig. 33.2, 33.3 and 33.4) F: For the remaining 2 holes, attach with 2 (S13) #6 x 5/8”...
  • Page 82 A: Attach KidKraft I.D. Plaque to a location on your set that is easily seen and read by a supervising adult using 4 (S13) Pan Screws as shown below. KidKraft I.D. Plaque Hardware Other Parts 1 x KidKraft I.D. Plaque Pan Screw...
  • Page 83 Step 35: Swing Wall A: Attach the (9481) SW Side Panel Assembly with 6 (S0) Wood Screws. Ensure the assembly is flush with the (2756) Siding Assemblies and tight to the (2630) SW Top. (fig. 35.1 and 35.2) 9481 Fig. 35.1 2630 Fig.
  • Page 84 Step 36: Ladder Assembly Part 1 A: Place 2 (11380) M-Ladder Post on a hard, flat surface with the chamfered edges facing down. (fig. 36.1) B: Tap 6 (TN1) into the rung holes. Fig. 36.1 11380 Chamfered Edge Chamfered Edge 11380 Wood Parts Hardware...
  • Page 85 Step 36: Ladder Assembly Part 2 C: Carefully turn over the (11380) M-Ladder Post D: Place 3 (11381) M-Ladder Support on top, making sure the edges are flush to the edges of (11380) M-Ladder Post. Attach with 6 (H11) Hex Bolts (with lock washer and flat washer) connecting to the previously installed t-nuts.
  • Page 86 Step 36: Ladder Assembly Part 3 E: Turn the ladder assembly over. Note the hole locations. (fig. 36.4) F: Place (11382) M-Ladder on the (11380) M-Ladder Post. Ensure the bottom and side edges are flush. Attach with 2 (S20) Wood Screws per board. (fig. 36.4 and 36.5) 11380 Fig.
  • Page 87 Step 36: Ladder Assembly Part 4 G: Center the Ladder Assembly on the SW Wall. Ensure the bottom of the ladder is flush with the floorboards and that the back of the ladder is tight to the SW Wall. Attach with 2 (S7). (fig. 36.6 and 36.7) Fig.
  • Page 88 Step 36: Ladder Assembly Part 5 H: On the exterior side of the SW Wall pre-drill 6 holes with a 1/8” (3.2 mm) drill bit at the locations shown (fig. 36.9). Ensure each pre-drilled hole has a depth of 1”. I: Secure the ladder to the SW Wall with 6 (S7) Pan Screws.
  • Page 89 Step 37: Crow’s Nest Frame Part 1 A: Place 2 (11183) Crow Nest Post B on a hard, flat surface. The top of the posts have chamfered edges. (fig. 37.1) B: Tap in 2 (TN2) T-nuts per board. C: On the inside faces of the posts tap in 1 (TN1) T-nut per board. D: Set the boards aside for a later step.
  • Page 90 Step 37: Crow’s Nest Frame Part 2 E: Place 2 (11370) Platform Post A on a hard, flat surface. The top of the posts have chamfered edges. (fig. 37.2) F: Tap in 3 (TN1) T-nuts per board. G: On the inside faces of the posts of the posts tap in 1 (TN1) T-nut per board. H: Set the boards aside for a later step.
  • Page 91 Step 37: Crow’s Nest Frame Part 3 I: Place the 2 previous (11183) Crow Nest Post B on a hard, flat surface with the TN facing down. (fig. 37.3) J: Place (11186) Bottom Nest Top B at the bottom of the posts, leaving 1” (25.4mm) overhang on either side of the board.
  • Page 92 Step 37: Crow’s Nest Frame Part 4 M: Place the frame on a hard, flat surface so that the (11186) Bottom Nest Top B is on the bottom and its notch is facing to the top. (fig. 37.5) N: Place boards (11185) Bottom Nest Top A and (11184) Crow Nest Floor Support on either side of the left (11183) Crow Nest Post B.
  • Page 93 Step 37: Crow’s Nest Frame Part 5 R: Repeat the previous step for the Right side of the frame. (fig. 37.7 and 37.8) Flush Fig. 37.8 Fig. 37.7 Rotated View 11184 11368 11368 11186 11185 11184 11185 Flush Hardware Wood Parts Crow Nest Post A Hex Bolt (lock washer, 11368...
  • Page 94 Step 37: Crow’s Nest Frame Part 6 S: Flush to the edge of the (11368) Crow Nest Post A attach 1 Swing Bracket with 1 (G8) Hex Bolt (with lock washer, 2 flat washers, lock nut) per board. (fig. 37.9) 11368 Swing Bracket...
  • Page 95 Step 38: Attach Crow’s Nest Part 1 A: With an adult helper and a ladder, hoist the frame over the (2614) Engineered Beam. Make sure the notch on the frame is tight to the Beam. (fig. 38.1) B: Use 2 (11206) Crow Nest Floor B for alignment, make sure the Crow Nest frame is square. (fig. 38.4) C: Using the swing brackets as a guide, pre-drill holes with a 1/8”...
  • Page 96 Step 38: Attach Crow’s Nest Part 2 E: Place the (11194) Nest Post tight against the (11186) Bottom Nest Top B and level with the (2614) Engineered Beam. (fig. 38.5, 38.6) F: Align the outermost holes to the corresponding holes on (11186) Bottom Nest Top B and attach 1 (G9) Hex Bolt (with lock washer, 2 flat washers, and lock nut) per board.
  • Page 97 Step 38: Attach Crow’s Nest Part 3 G: Align 2 Swing Brackets with their corresponding hole on the (11194) Nest Post. Make sure the brackets are square and tight to the (2614) Engineered Beam. Fasten with 2 (G27) Hex Bolts (with lock washer, 2 flat washers, and lock nut).
  • Page 98 Step 38: Attach Crow’s Nest Part 4 H: On the front and back of the (2614) Engineered Beam predrill holes using the Swing Bracket as a guide and a 1/8” (3.2mm) drill bit. Ensure the holes are 1” (25.4mm) deep and that the brackets are square to the Beam. (fig. 38.9) I: Fasten the Brackets to the Beam with 1 (WL3) Wafer Lag (with lock washer and flat washer) per side.
  • Page 99 Step 39: Crow’s Nest Assembly Part 1 A: Place (11206) Crow Nest Floor B on the (11184) Crow Nest Floor Support and tight against (11186) Bottom Nest Top B. (fig. 39.1, 39.2) B: Attach the floorboard to the Boards and Beam with 5 (S20) Wood Screws. (fig. 39.2) Fig.
  • Page 100 Step 39: Crow’s Nest Assembly Part 2 C: Place 3 (11205) Crow Nest Floor A on the (11184) Crow Nest Floor Support. (fig. 39.3 and 39.4) D: Place (11206) Crow Nest Floor B on the (11184) Crow Nest Floor Support and tight against (11368) Crow Nest Post A.(fig.
  • Page 101 Step 39: Crow’s Nest Assembly Part 3 G: Place the (11370) Platform Post A tight against (11185) Bottom Nest Top A and (11368) Crow Nest Post A. Attach with 2 (H8) Hex Bolts (with lock washer and flat washer) connecting to previously installed t-nuts per board.
  • Page 102 Step 39: Crow’s Nest Assembly Part 4 H: Place 2 (11369) Crow Nest Top A boards on the outsides of the Crow’s Nest Frame Posts. Ensure the top edges are flush with the top of the Posts. Ensure the edges are flush with (11183) Crow Nest Post B. (fig. 39.7) I: Attach each board with 2 (H10) Hex Bolts (with lock washer and flat washer) connecting to the previously installed t-nuts.
  • Page 103 Step 39: Crow’s Nest Assembly Part 5 J: Place (11190) Crow Nest Top B on the outside of (11183) Crow Nest Post B making sure the top edges are flush. Ensure the side edges are flush with (11369) Crow Nest Top A. (fig. 39.9 and 39.10) K: Attach with 2 (G4) Hex Bolts (with lock washer and flat washer) connecting to the previously installed t-nuts.
  • Page 104 Step 39: Crow’s Nest Assembly Part 6 L: Place 1 (11191) Top Fence on a hard, flat surface. Tap 2 (TN2) T-nuts into each hole. Repeat for the other 9 (11191) Top Fence. (fig. 39.11) Fig. 39.11 11191 Wood Parts Hardware 10 x Top Fence...
  • Page 105 Step 39: Crow’s Nest Assembly Part 7 M: Attach 3 (11191) Top Fence to the inside of the crow’s nest with 2 (G27) Hex Bolts (with lock washer and flat washer) connecting to the previously installed t-nuts per board. (fig. 39.12 and 39.13) Fig.
  • Page 106 Step 39: Crow’s Nest Assembly Part 8 N: Attach 4 (11191) Top Fence to the inside of the crow’s nest with 2 (G27) Hex Bolts (with lock washer and flat washer) connecting to the previously installed t-nuts per board. (fig. 39.14 and 39.15) Fig.
  • Page 107 Step 39: Crow’s Nest Assembly Part 9 O: Attach 3 (11191) Top Fence to the inside of the crow’s nest with 2 (G27) Hex Bolts (with lock washer and flat washer) connecting to the previously installed t-nuts per board. (fig. 39.16 and 39.17) Fig.
  • Page 108 Step 39: Crow’s Nest Assembly Part 10 P: Place 1 Hand Grip centered on the inside of each (11370) Platform Post A and 6” (152.4mm) above the floorboards. (fig. 39.19) Q: Predrill holes using the Hand Grip as a guide and a 1/8” (3.2mm) drill bit. Ensure the holes are 1” (25.4mm) deep.
  • Page 109 Step 40: Roof Attachment Prep Part 1 A: Remove the indicated hardware. It will no longer be used and can be discarded. (fig. 40.1) Fig. 40.1...
  • Page 110 Step 40: Roof Attachment Prep Part 2 B: Place 1 (11376) Short Post tightly against the Swing Wall at the corner where it meets the Front Wall as shown on fig. 40.4. Ensure the bottom of Short Post is 3” (76.2mm) below the top of the Swing Wall. Note the larger hole on Short Post is located toward the bottom.
  • Page 111 Step 40: Roof Attachment Prep Part 3 G: Place 4 (11375) Roof Bottom Post flush to the (11376) Short Post from the previous step. (fig. 40.5, 40.6 and 40.7) H: At the corners where the parts stack, fasten 2 (S11) Wood Screws from (11376) Short Post into (11375) Roof Bottom Post per board.
  • Page 112 Step 41: Sky Windows Part 1 A: Place 2 (11374) Top Roof Post on a hard, flat surface with the notches at the top facing up. (fig. 41.1) B: Place (11373) Lookout Wall Back in the grooves and tap in a (TN2) T-nut at each end. C: Make sure the parts are flush and square.
  • Page 113 Step 41: Sky Windows Part 2 E: Place the MOD 5 Pane Side Lite Window on (11373) Lookout Wall Back with the tab tightly against the bottom edge of (11373) and the sides flush to (11374). Fasten with 6 (S0) Wood Screws. (fig. 41.2) F: Repeat for the second frame.
  • Page 114 Step 41: Sky Windows Part 3 G: Mount the window frames at the top of the fort, resting the bottom tab of the window on (2775) Panel Cross Support, and keeping the edges flush. H: Fasten with 6 (S0) Wood Screws per window. (fig. 41.3) Fig.
  • Page 115 Step 41: Sky Windows Part 4 I: For each frame, attach the inside left corner to the (11376) Short Post with 2 (S4) Wood Screws. (fig. 41.4 and 41.5) J: For each frame, attach the inside right corner to the (11376) Short Post with 2 (S11) Wood Screws. (fig.
  • Page 116 Step 42: Roof Support Assembly A: Attach 1 (2760) Roof Support to a second (2760) Roof Support at peak using 1 (S4) Wood Screw. Repeat this step so there are 2 Roof Support Assemblies. (fig. 42.1 and 42.2) Fig. 42.1 Roof Support Assembly 2760...
  • Page 117 Step 43: Roof Panel Assembly A: Place 1 (2751) MOD Roof Bottom tight to the bottom of (2752) MOD Roof Front and (2753) MOD Roof Back. (fig.43.1) B: Place a (2761) Roof Sleeper C on the middle strip of each Roof Panel Assembly so the ends are flush and attach with 4 (S20) Wood Screws per panel.
  • Page 118 Step 44: Roof Assembly A: Place Front Roof Panel against Back Roof Panel so the tops form a peak then tight to the inside edge of the outside slats attach 1 Narrow Angle Bracket per slat with 2 (S0) Truss Screws per bracket. (fig. 44.1 and 44.2) B: Attach the third Narrow Angle Bracket centred on the middle slat with 2 (S0) Truss Screws.
  • Page 119 Step 45: Roof Assembly A: Place 1 Roof Support Assembly against one side so the peaks meet and the ends of the roof supports are flush with the ends of the roof panels. Attach with 8 (S11) Wood Screws. (fig. 45.1) B: Attach the second Roof Support Assembly on the opposite side, peaks to meet and ends are flush with 8 (S11) Wood Screws.
  • Page 120 Step 46: Attach Peak Detail A: Attach 1 Peak Detail to the inside of the (2760) Roof Supports on side of the Roof Assembly with 8 (S8) Pan Screws (with 1/4” flat washer). (fig. 46.1 and 46.2) Fig. 46.1 Roof Assembly with 1/4”...
  • Page 121 Step 47: Roof Attachment Part 1 A: With an adult helper, a ladder, and 1 person standing on the inside of the fort, hoist the roof up & over the (11375) Roof Bottom Post. Note the gable side faces the TNR Slide. (fig. 47.1) B: At the TNR side, attach the Roof to (11375) Roof Bottom Post from the inside of the fort with 2 (S11) Wood Screws per board.
  • Page 122 Step 47: Roof Attachment Part 2 C: Rest the angle cut of (11371) Platform Bottom on the roof and align its large hole with the corresponding hole on (11370) Platform Post A. Ensure the top edge is flush with the post. (fig. 47.4, 47.5) D: Attach to (11370) with 1 (H8) Hex Bolt (with lock washer and flat washer) connecting to the previously installed t-nut and 1 (S3) Wood Screw.
  • Page 123 Step 47: Roof Attachment Part 3 G: At the Swing Wall side, attach the Roof to (11375) Roof Bottom Post from the inside of the fort with 2 (S11) Wood Screws per board. (fig. 47.6) Fig. 47.6 11375 11375 Inside View Inside View Hardware Wood Screw...
  • Page 124 Step 47: Roof Attachment Part 4 H: On the (2760) Roof Support facing the crow’s nest mark a point along the centerline on the edge of both (11370) Platform Post A. (fig. 47.7 and 47.8) I: Predrill holes at the marked points using a 1/8” (3.2mm) drill bit. Ensure the hole is 1” (25.4mm) deep. J: Fasten the roof to both (11370) Platform Post A using 1 (S4) Wood Screw per board.
  • Page 125 Step 47: Roof Attachment Part 5 K: On the inside of the crow’s nest center the (11383) Roof Top across (11371) Platform Bottom and (11372) Platform Top. Attach with 6 (S20) Wood Screws. (fig. 47.9, 47.10) Fig. 47.9 11383 Fig. 47.10 Note hole orientation 11372 11371...
  • Page 126 Step 47: Roof Attachment Part 6 L: Place (11378) Roof Bottom Post A with its notch tight against the (2630) SW Top and 2” (50.8mm) away from (11375) Roof Bottom Post. (fig. 47.11, 47.12) M: Fasten the board to (2630) SW Top using 1 (S20) Wood Screw. (fig. 47.12) N: Fasten the board to (2760) Roof Support using 1 (S4) Wood Screw.
  • Page 127 Step 47: Roof Attachment Part 7 O: Repeat the previous step for the (11379) Roof Bottom Post B. (fig. 47.13, 47.14) Fig. 47.13 11379 Fig. 47.14 2760 11375 11379 2” 50.8mm 2630 Inside View Hardware Wood Parts Wood Screw Roof Bottom Post B 11379 Wood Screw...
  • Page 128 Step 48: Attach Acro and Belt Swings A: Using 1 Threaded Clip per chain, join 1 Long Swing Chain to each side of the swing belt seat. Make sure to close the Threaded Clip tightly using an adjustable wrench. (fig. 48.1 and 48.2). B: Using 1 Threaded Clip per chain, join the Short Swing Chain to the Acro Bar and Acro Handle.
  • Page 129 NOTES...
  • Page 130 NOTES...
  • Page 131 NOTES...
  • Page 132 2) Complete the registration online at: https://www.kidkraft.com/us_en/warranty/ 3) Mail this completed form to: KidKraft Inc., 4630 Olin Road, Dallas, Tx 75244 USA Make sure to include a copy of your proof of purchase...

This manual is also suitable for:

F29735