Download
Share
Print this page
KidKraft RIDGEVIEW DELUXE CLUBHOUSE PLAY SYSTEM Installation And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. KidKraft Manuals
  4. Play Sets & Playground Equipment
  5. RIDGEVIEW DELUXE CLUBHOUSE PLAY SYSTEM
  6. Installation and operating instructions manual

KidKraft RIDGEVIEW DELUXE CLUBHOUSE PLAY SYSTEM Installation And Operating Instructions Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
RIDGEVIEW DELUXE CLUBHOUSE
INSTALLATION AND OPERATING INSTRUCTIONS
26' 5"
14' 5"
13' 6"
10-14 Hrs
Two person
assembly
KidKraft, Inc.
4630 Olin Road
Dallas, Texas 75244 USA
customerservice@kidkraft.com
canadacustomerservice@kidkraft.com
1.800.933.0771
972.385.0100
For online parts replacement visit
https://parts.kidkraft.com/
PLAY SYSTEM - F270855
WARNING
and give them to any future owner of this play system. Manufacturer contact information provided below.
OBSTACLE FREE SAFETY ZONE - 26'5" x 26' 6" area requires Protective Surfacing. See page 3.
26' 6"
MAXIMUM VERTICAL FALL HEIGHT - 6'5"
CAPACITY - 9 Users Maximum, Ages 3 to 10; Weight Limit 110 lbs. (49.9 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools, churches, nurseries, day cares or parks.
Warning. Only for demestic use.
KidKraft Netherlands BV
Olympisch Stadion 8
1076 DE Amsterdam
The Netherlands
europecustomerservice@kidkraft.com
+31 20 305 8620 M-F from 09:00 to 17:30
(GMT+1)
For online parts replacement visit
https://parts.kidkraft.eu/
To reduce the risk of serious injury or death, you must read and
follow these instructions. Keep and refer to these instructions often

Table of Contents

Warnings and Safe Play Instructions. . . . . . . . . . . . . . . pg. 2
Protective Surfacing Guidelines. . . . . . . . . . . . . . . . . . . pg. 3
Instructions for Proper Maintenance . . . . . . . . . . . . . . . pg. 4
About Our Wood - Limited Warranty . . . . . . . . . . . . pg. 5-6
Keys to Assembly Success . . . . . . . . . . . . . . . . . . . . . . pg. 7
Metric Conversion Sheets . . . . . . . . . . . . . . . . . . . . . pg. 8-9
Part ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 10
Installation of I.D./Warning Plaque . . . . . . . . . . . .Final Step
9400855
Rev 03/30/2020

Advertisement

loading

Related Manuals for KidKraft RIDGEVIEW DELUXE CLUBHOUSE PLAY SYSTEM

Summary of Contents for KidKraft RIDGEVIEW DELUXE CLUBHOUSE PLAY SYSTEM

  • Page 1: Table Of Contents

    Instructions for Proper Maintenance ....pg. 4 KidKraft, Inc. KidKraft Netherlands BV About Our Wood – Limited Warranty ... . pg. 5-6...

  • Page 2: Warnings And Safe Play Instructions

    Warnings and Safe Play Instructions CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using this play system.

  • Page 3: Protective Surfacing Guidelines

    Protective Surfacing - Reducing Risk of Serious Head Injury From Falls One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable for the equipment height in accordance with ASTM F1292.

  • Page 4: Instructions For Proper Maintenance

    Instructions for Proper Maintenance Your KidKraft Play System is designed and constructed of quality materials with your child’s safety in mind. As with all outdoor products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your Play Set, it is important that you, the owner, properly maintain it.

  • Page 5: About Our Wood - Limited Warranty

    About Our Wood KidKraft Premium Play Systems uses only premium playset lumber, ensuring the safest product for your children’s use. Although we take great care in selecting the best quality lumber available, wood is still a product of nature and susceptible to weathering which can change the appearance of your set.
  • Page 6 KidKraft Limited Warranty MISSING OR DAMAGED PARTS: KidKraft will replace any parts within 90 days from date of purchase found to be missing from or damaged in the original packaging. See Fig.1 Fig. 1 Product Age (All Parts) Consumer Pays...

  • Page 7: Keys To Assembly Success

    Keys to Assembly Success Tools Required • Tape Measure • #1 Phillips, #2 Robertson • Open End Wrench • 3/16”(5mm) Hex Key • Carpenters Level and Screwdriver 1/2” (13mm) & 9/16”(14 mm) • 8’ (2.4m) Step Ladder • Carpenters Square •...

  • Page 10: Part Id

    Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Nominal Size Actual Size 5pc. - 1848 CE Siding (3/8 x 3-1/2 x 9") - Box 3 - 3631848 1" x 2" ⅝" x 1⅜" 1"...
  • Page 11 Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Nominal Size Actual Size 1pc. - 1869 Door Top (1 x 4 x 46-5/8") - Box 2 - 3641869 1" x 4" ⅝" x 3⅜" 1"...
  • Page 12 Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Nominal Size Actual Size 3pc. - 0630 CE Rock Board (1 x 6 x 19 3/4") - Box 2 - 3630630 ⅝" x 5⅜" 1" x 6" 1"...
  • Page 13 Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Nominal Size Actual Size 2pc. - 1367 Post MK (2 x 3 x 70") - Box 3 - 3641367 2" x 3" 1⅜" x 2½" 2"...
  • Page 14 1X 3320386 Rocks (5pk) Green 3-Green 2-Yellow 1X 3202000 Swing Hanger Bolt Thru. (4 pk) 1X 9320374 1X 3320356 KidKraft I.D Plaque w Big Backyard I.D hardware Plaque w hardware 1X 3533860 39" Glider Rope & Chain (4pk) w. welded chain 1X 3200202...
  • Page 15 Hardware Identification (Actual Size) 1/4 x 1-1/2" 4pc. LS1 - Lag Screw - (9262212) 1/4 x 2-1/2" 3pc. LS2 - Lag Screw - (9272222) 1/4 x 3" 8pc. LS3 - Lag Screw - (9262230) Hex Bolt 1/4 x 1-1/2" 1pc. H1 - - (9277212) Hex Bolt 1/4 x 2"...
  • Page 16 Hardware Identification (Actual Size) Hex Bolt 5/16 x 1" 4pc. G2 - - (9277310) Hex Bolt 5/16 x 1-1/2" 4pc. G1 - - (9277312) Hex Bolt 5/16 x 2" 2pc. G8 - - (9277320) Hex Bolt 5/16 x 3" 3pc. G10 - - (9277330) Hex Bolt 5/16 x 4"...
  • Page 17 Hardware Identification (Actual Size) 39pc. TN1 - 1/4" T - Nut (9285200) 25pc. FW3 - #8 Flat Washer - (9251500) 20pc. LW2 - 5/16" Lock Washer - (9253300) 19pc. FW0 - 3/16" Flat Washer - (9251100) 20pc. TN2 - 5/16" T- Nut (9285300) 44pc.
  • Page 18 Before you discard your cartons fill out the form below. • The carton I.D. stamp is located on the end of each carton. The tracking number is located on the KidKraft ID Plaque (9320374). • Please retain this information for future reference. You will need this information if you contact the Consumer Relations Department.
  • Page 19 Step 2: Rock Wall Assembly Fig. 2.1 Note: The holes 0631 0631 in the rock boards 0606 0349 must orient to the top of the boards. 0630 0630 0630 7-3/4” Approx Note: Gaps between boards 2-1/4”, not to exceed 2-3/8” A: Lay 2 (0349) Rock Rails down, side by side with angled edges facing down.
  • Page 20 Step 3: Swing Beam Assembly Warning: For your child’s safety, Fig. 3.4 orientate the swing hangers as shown to ensure your swing will have proper swing motion when installed. Failure to do so could result in premature failure of the swing hanger or swing chain.
  • Page 21 Step 4: Swing End Assembly A: Attach 2 (1863) SW Posts to (1856) SW Upright using 2 (G4) 5/16 x 4” Hex Bolts (with lock washer, flat washer and t-nut). (fig. 4.1) Fig. 4.1 5/16” Lock Washer 1863 1862 1856 5/16”...
  • Page 22 Step 5: Attach Swing End to Swing Beam A: Place (4919) SW Rail Block in the centre between (1826) Front Beam and (1825) Back Beam and attach with 1 (H8) 1/4 x 4-1/4” Hex Bolt (with lock washer, flat washer and t-nut). (fig. 5.1 & 5.2) Fig.
  • Page 23 Step 6: Monkey Rail Assembly Pre-drill all pilot holes using a 1/8” drill bit before installing wood screws. A: Insert 3 (578) 1-1/8 x 15-7/8” Dowels into both (1564) MK Rail Longs as shown in fig. 6.1. Note the pilot holes in one of the (1564) MK Rail Long are on the bottom of the board.
  • Page 24 Step 7: Monkey Ladder Assembly Note: Pre-drill all holes using a 1/8” drill bit before installing the lag screws and wood screws. A: Insert 1 (858) 1-1/8 x 18-5/8” Dowel into 2 (1367) Post MK as shown in fig. 7.1. Fig.
  • Page 25 Step 8: Connect Monkey Bar Assemblies Note: Pre-drill all holes using a 1/8” drill bit before installing the pan screws. A: Using a Monkey Bracket connect both (1564) MK Rail Longs to each (1367) Post MK with 1 (G10) 5/16 x 3”...
  • Page 26 Step 9: Roof Assembly Step * ** Part 1 A: Attach 1 (0863) Roof Support to another at the peak using 1 (S4) #8 x 3” Wood Screw. Do this twice so you have 2 Roof Support Assemblies. (fig. 9.1) B: Attach 1 (0501) Joist to another at the peak using 1 (S4) #8 x 3”...
  • Page 27 Step 9: Roof Assembly Part 2 D: Starting at the top of the Roof Support Assembly attach 1 (0517) Cedar Roofing on each side of the (0863) Roof Supports and (0501) Joists with 3 (S0) #8 x 7/8” Truss Screws per board. (fig. 9.2) Be sure to overlap the top of the boards so there are no gaps.
  • Page 28 Step 9: Roof Assembly Part 3 H: To assemble the Dormer Assembly insert the 2 Dormer Sides into the Dormer Front. (fig. 9.5) I: Attach (0520) Window Dormer Roof Right and (0521) Window Dormer Roof Left together with the Window Domer Bracket using 2 (S5) #8 x 1/2”...
  • Page 29 Step 9: Roof Assembly Part 4 K: On the front of the Roof Assembly, on the sixth (0517) Cedar Roofing from the bottom, place (0522) Window Dormer Cleat centred over the middle screw. Use the Dormer Assembly as a guide to make sure the spacing is correct, pre-drill using a 1/8”...
  • Page 30 Step 9: Roof Assembly Part 5 N: Place 1 Peak Detail - Green on each side of the Roof Assembly and attach to (0863) Roof Supports with 8 (S8) #12 x 3/4” Pan Screws (with 1/4” flat washer) per Peak Detail - Green as shown in fig. 9.9. Fig.
  • Page 31 Step 10: Cafe Wall Assembly Note: Pre-drill all holes using a 1/8” drill bit before installing the lag screws. A: On the ground lay flat 2 (1500) Posts then attach (1874) Side Ground with 4 (H2) 1/4 x 2” Hex Bolts (with lock washer, flat washer and t-nut);...
  • Page 32 Step 11: Swing Wall Assembly Part 1 A: Attach (1872) Ground using 4 (H2) 1/4 x 2” Hex Bolts (with lock washer, flat washer and t-nut); (1501) Floor End (in the bottom holes) and (1865) SW Roof Side using 2 (H2) 1/4 x 2” Hex Bolts (with lock washer, flat washer and t-nut) for each board to 2 (1500) Posts.
  • Page 33 Step 11: Swing Wall Assembly Part 2 Note: Pre-drill all holes using a 1/8” drill bit before installing the lag screws. D: Attach 1 (0369) Lower Diagonal to each end of (1872) Ground with 1 (H2) 1/4 x 2” Hex Bolt (with lock washer, flat washer and t-nut) per diagonal.
  • Page 34 Step 12: Lower Fort Frame Assembly A: On the back side of the assembly, attach (1873) Back Floor to both (1500) Posts using 2 (H5) 1/4 x 4-1/2” Hex Bolts (with lock washer, flat washer and t-nut). (fig. 12.1 and 12.2) Notice the middle bolt holes are towards the bottom of the board.
  • Page 35 Step 13: Back Frame Assembly A: Attach (1860) MK Mount to (1873) Back Floor with 1 (H13) 1/4 x 3-1/2” Hex Bolt (with lock washer, flat washer and t-nut) and to (1857) Top Back with 1 (H12) 1/4 x 3” Hex Bolt (with lock washer, flat washer and t-nut). (fig. 13.1 and 13.2) B: Make sure (1857) Top Back is level and the distance between the bottom of (1857) Top Back and the top of (1873) Back Floor is 28-5/8”, then attach to both (1500) Posts using 4 (S7) #12 x 2”...
  • Page 36 Step 14: Front Frame Assembly A: Attach (1855) Divider to (0799) Floor Back with 1 (H1) 1/4 x 1-1/2” Hex Bolt (with lock washer, flat washer and t-nut) and to (1505) Front Top with 1 (PB2) 1/4 x 1-1/4” Pan Bolt (with lock washer, flat washer and t-nut). (fig. 14.1 and 14.2) B: Make sure (1505) Front Top is level and then attach to both (1500) Posts using 4 (S7) #12 x 2”...
  • Page 37 Step 15: Attach Floor Joist A: Loosen the top bolt and remove the bottom bolt in (1861) SW Mount. Do not discard these bolts, you will re- install them after the (0790) Floor Joist is attached. (fig. 15.1) B: From inside of the assembly, measure 2” down from the top of each (1501) Floor End (fig. 15.2) and then attach (0790) Floor Joist to each board in the top pilot holes with 2 (S4) #8 x 3”...
  • Page 38 Step 16: Attach Side Joists Part 1 A: On the front of the assembly attach (0795) Side Joist to the inside of (0799) Floor Back with 2 (H3) 1/4 x 2-1/2” Hex Bolts (with lock washer, flat washer and t-nut) in the outside holes and 2 (S7) #12 x 2” Pan Screws in the inside holes as shown in fig.
  • Page 39 Step 16: Attach Side Joists Part 2 B: On the back of the assembly attach one (1875) Short Joist and one (1871) Long Joist on each side of (1860) MK Mount, to the inside of (1873) Back Floor with 1 (H3) 1/4 x 2-1/2” Hex Bolt (with lock washer, flat washer and t-nut), per board, in the outside holes.
  • Page 40 Step 17: Attach Gap and Floor Boards A: Place 1 (1853) Cedar Gap Board at each end of the assembly. Then starting on the Swing Wall side place 4 (1851) Cedar Floor Boards, 1 (1854) Centre Gap Board so the gap in the board fits around the (1860) MK Mount, and 3 more (1851) Cedar Floor Boards.
  • Page 41 Step 18: Attach Ground Stakes MOVE FORT TO FINAL LOCATION. FINAL LOCATION MUST BE LEVEL GROUND Warning! To prevent tipping and avoid potential injury, stakes must be driven 10-1/2” into ground. Digging or driving stakes can be dangerous if you do not check first for underground wiring, cables or gas lines. A: Drive 2 (0318) Ground Stakes 10-1/2”...
  • Page 42 Step 19: Swing Side Wall Assembly A: In between both (1500) Posts on Swing Wall side attach 4 (1846) CE Wall to (1501) Floor End and (1865) SW Roof Side using 4 (S1) #8 x 1-1/8” Wood Screws per board. Make sure the bottom of the boards are tight against (1853) Cedar Gap Board.
  • Page 43 Step 20: Attach Cafe Canopy to Fort A: Feed Cafe Canopy Frame through the pocket of the Cafe Canopy. (fig. 20.1) B: With a helper, hold the Cafe Canopy Frame against the (1500) Posts on the Cafe Wall. The top of the canopy should rest on top of (1501) Floor End.
  • Page 44 Step 21: Cafe Window Assembly Part 1 A: Place 1 (1859) Wall Trim tight to the top of (1501) Floor End and flush to the outside edge of (1500) Post on the Cafe Wall side of the assembly. Attach to (1500) Post with 2 (S2) #8 x 1-1/2” Wood Screws. (fig. 21.1 and 21.2) B: Tight to top of (1501) Floor End and tight to (1859) Wall Trim attach (1852) CE Siding to both (1500) Posts with 2 (S0) #8 x 7/8”...
  • Page 45 Step 21: Cafe Window Assembly Part 2 G: On the inside of the assembly, tight to both (1500) Posts and and flush to the bottom of (1864) SL Roof Side, attach 2 (0606) CE Access Boards to (1867) Top Side and (1851) Cedar Floor Board with 4 (S1) #8 x 1-1/8” Wood Screws per board.
  • Page 46 Step 21: Cafe Window Assembly Part 3 I: Fold Mesh both sides inward by 75mm, please keep folded mesh to flush with wood(0606) and attached the fold mesh with with 8 (S0) #8 x 7/8” Truss Screws and 8 (FW3).(fig.21.5 & 21.6) J: Measure 5-1/2”...
  • Page 47 Step 21: Cafe Window Assembly Part 4 K: From the outside of the assembly attach (1852) CE Siding to each (1866) Window Upright with 2 (S0) #8 x 7/8” Truss Screws per siding. (fig. 21.8 and 21.9) Fig. 21.8 1866 Fig.
  • Page 48 Step 22: Chalk Wall Frame Assembly A: On the back of the assembly, tight to the top of (1873) Back Floor, attach (5265) Cedar Wall flush to the outside edges of (1500) Post and (1860) MK Mount with 4 (S2) #8 x 1-1/2” Wood Screws. (fig. 22.1 and 22.2) B: Attach 1 (0528) Side Chalkwall flush to the outside edges of (1500) Post and (1860) MK Mount and tight to the top of (5265) Cedar Wall with 5 (S2) #8 x 1-1/2”...
  • Page 49 Step 23: Attach Chalkwall Tarp to Fort A: On the outside of the assembly, making sure the tarp is tight and smooth, attach Chalkwall Tarp to (1857) Top Back, (5265) Cedar Wall and both (0528) Side Chalkwalls using 12 (S5) #8 x 1/2” Pan Screws (with #8 flat washer) as shown in fig.
  • Page 50 Step 24: Roof Frame Assembly A: Attach 1 (0357) Tarp Front Back to each end of (1864) SL Roof Side and (1865) SW Roof Side, making sure the pilot holes are centred on the end of each Roof Side, with 4 (S2) #8 x 1-1/2” Wood Screws per (0357) Tarp Front Back.
  • Page 51 Step 25: Attach Floor Gussets Pre-drill all pilot holes using a 1/8” drill bit before installing the lag screws. A: On the Swing Wall side place 1 (0367) Floor Gusset tight to the inside face of each (1500) Post, to the bottom of (1853) Cedar Gap Board and inside face of (1501) Floor End.
  • Page 52 Step 26: Lower Swing Wall Assembly Part 1 A: Place 1 (1808) Short Trim tight to the top of (1872) Ground flush to the outside edge of (1500) Post on the Swing Wall side of the assembly. Attach to (1500) Post with 3 (S2) #8 x 1-1/2” Wood Screws. (fig. 26.1 and 26.2) B: Tight to top of (1872) Ground and tight to (1808) Short Trim attach (1852) CE Siding to both (1500) Posts with 2 (S0) #8 x 7/8”...
  • Page 53 Step 26: Lower Swing Wall Assembly Part 2 F: From inside the assembly, centred over the pilot holes in (1852) CE Siding, attach 2 (1858) Short Wall Supports to (0839) CE Gap Board and (1872) Ground with 4 (S1) #8 x 1-1/8” Wood Screws per board. (fig. 26.3 and 26.4) G: From the outside of the assembly attach (1852) CE Siding to each (1858) Short Wall Support with 2 (S0) #8 x 7/8”...
  • Page 54 Step 27: Door Wall Assembly Part 1 A: Tight to the bottom of (1873) Back Floor attach (1869) Door Top flush to the edges of both (1500) Posts with 4 (S2) #8 x 1-1/2” Wood Screws. (fig. 27.1 and 27.2) B: Flush to the edge of the arch in the (1869) Door Top and flush to the bottom of (0351) Front Back attach (1814) Wall Support to (1873) Back Floor and (0351) Front Back with 4 (S1) #8 x 1-1/8”...
  • Page 55 Step 27: Door Wall Assembly Part 2 D: Tight to the top of (0351) Front Back and tight to (1809) Door Trim attach 1 (1847) Siding to (1814) Wall Support and (1500) Post with 2 (S0) #8 x 7/8” Truss Screws as shown in fig. 27.7. E: Evenly space then install 10 more (1847) Siding directly above the first, attaching to (1814) Wall Support and (1500) Post with 2 (S0) #8 x 7/8”...
  • Page 56 Step 28: Lower Cafe Wall Assembly Part 1 A: Place 1 (1870) Trim Short tight to the top of (1874) Side Ground and the outside edge of (1847) Siding on the Door Wall side of the assembly. Attach to (1500) Post with 3 (S2) #8 x 1-1/2” Wood Screws. (fig. 28.1 and 28.2) B: Tight to top of (1874) Side Ground and tight to (1870) Trim Short attach (1852) CE Siding to both (1500) Posts with 2 (S0) #8 x 7/8”...
  • Page 57 Step 28: Lower Cafe Wall Assembly Part 2 E: Place (0376) Table Top centred over (1868) Table Support so the corner of the angled edge of (0376) Table Top is flush to the face of (1868) Table Support. The (1868) Table Support should overhang the (0376) Table Top on both sides by 3-3/8”.
  • Page 58 Step 28: Lower Cafe Wall Assembly Part 3 H: From inside the assembly, centred over the pilot holes in (1852) CE Siding, attach 2 (1858) Short Wall Supports to (1868) Table Support and (1874) Side Ground with 4 (S1) #8 x 1-1/8” Wood Screws per board. (fig. 28.8 and 28.9) I: From the outside of the assembly attach (1852) CE Siding to each (1858) Short Wall Support with 2 (S0) #8 x 7/8”...
  • Page 59 Step 29: Lower Front Wall Assembly Part 1 A: Tight to the top of (0351) Front Back and tight to each (1870) Trim Short attach 1 (1849) Cedar Siding to both (1500) Posts with 2 (S0) #8 x 7/8” Truss Screws as shown in fig. 29.1 and 29.2. B: Install 4 more (1849) Cedar Siding directly above the first, attaching to both (1500) Posts with 2 (S0) #8 x 7/8”...
  • Page 60 Step 29: Lower Front Wall Assembly Part 2 E: Measure 15” from the outside edge of (1500) Post on the Cafe Wall side. From the inside of the assembly attach 1 (1814) Wall Support to (0799) Floor Back and (0351) Front Back with 4 (S1) #8 x 1-1/8” Wood Screws as shown in fig.
  • Page 61 Step 29: Lower Front Wall Assembly Part 3 H: Install and evenly space 5 (1850) Siding in the large opening between (1849) Cedar Sidings, attaching to (1500) Post and 2 (1814) Wall Supports with 3 (S0) #8 x 7/8” Truss Screws per board. (1850) Siding should be flush to outside edge of (1500) Post.
  • Page 62 Step 30: Attach Window to Fort A: On the outside of the assembly place Door Window tight to the siding and from the inside of the assembly attach Door Window to (1848) CE Siding and (1850) Siding with the included hardware. (fig. 30.1 and 30.2) Fig.
  • Page 63 Step 31: Attach Roof to Fort A: With two helpers place the Roof Assembly, from Step 9, on the fort as shown in fig. 31.1. The roof should be centred on the Roof Frame assembly and (0863) Roof Supports should be flush to the inside of the fort and resting on (1865) SW Roof Side and (1864) SL Roof Side.
  • Page 64 Step 32: Stool Seat Assembly A: Using the hardware provided with the Stool Seat Assembly attach 1 Seat to 1 Seat Support and then create a second seat as in fig. 32.1. B: Keeping the Cross Brace tight to the Seat Assemblies, fasten the Cross Brace to each of the Seat Assemblies using the hardware provided.
  • Page 65 Step 33: Attach Stool Seat and Flower Box to Fort A: Attach the Stool Seat Assembly to (1874) Side Ground using 2 (G2) 5/16 x 1” Hex Bolt (with lock washer, flat washer and t-nut) per Seat Assembly. (fig. 33.1 and 33.2) B: Attach a Flower Box, centred under the window on (1851) Cedar Floor Board with 2 (S5) #8 x 1/2”...
  • Page 66 Step 34: Connect Monkey Bar Assembly to Fort Part 1 Pre-drill all pilot holes using a 1/8” drill bit before installing the lag screws. A: Using a MB Mount Strap attach (1564) MK Rail Long to (1500) Post with 1 (G10) 5/16 x 3” Hex Bolt (with lock washer, flat washer and t-nut) in the centre hole and 2 (S6) #12 x 1”...
  • Page 67 Step 34: Connect Monkey Bar Assembly to Fort Part 2 C: Drive 1 (0318) Ground Stake 10-1/2” into the ground at one (1367) Post MK on the inside of the assembly and attach with 2 (S3) #8 x 2-1/2” Wood Screws. (fig. 34.1 and 34.4) Warning! To prevent tipping and avoid potential injury, stakes must be driven 10-1/2”...
  • Page 68 Step 35: Attach Slide to Fort A: Place Slide in the centre between (1855) Divider and (1500) Post. (fig. 35.1 and 35.2) B: Attach slide to fort through the (0799) Floor Back using 3 (S7) #12 x 2” Pan Screws. (fig. 35.2 and 35.3) Fig.
  • Page 69 Step 36: Attach Rock Rail to Fort A: Place Rock Wall Assembly from Step 2 centred between (1500) Post and (1855) Divider and flush to top of (0799) Floor Back (fig. 36.1 and 36.2). Attach (0349) Rock Rails to (0799) Floor Back using 4 (S15) #8 x 1-3/4” Wood Screws as shown in fig.
  • Page 70 Step 37: Attach Rock Rail Ground Stake A: Drive 1 (0318) Ground Stakes 10-1/2” into the ground at (0349) Rock Rail as shown in fig. 37.1. Attach using 2 (S3) #8 x 2-1/2” Wood Screws per ground stake. (fig. 37.2) Warning! To prevent tipping and avoid potential injury, stakes must be driven 10-1/2”...
  • Page 71 Step 38: Attach Swing Assembly to Fort A: Attach Swing Assembly from Step 5 to (1861) SW Mount with 1 (G5) 5/16 x 4-1/2” Hex Bolt (with lock washer, flat washer and t-nut) and 1 (G8) 5/16 x 2” Hex Bolt (with 2 flat washers and 1 lock nut) as shown in fig.
  • Page 72 Step 39: Attach Swing Ground Stakes A: Drive one (0318) Ground Stake 10-1/2” into the ground at each (1863) SW Post and attach with 2 (S3) #8 x 2-1/2” Wood Screws per ground stake. (fig. 39.1 and 39.2) Warning! To prevent tipping and avoid potential injury, stakes must be driven 10-1/2”...
  • Page 73 Step 40: Glider Assembly A: Attach 1 Glider End to the Glider Seat using 1 5/16” Glider Long Hex Bolt (with 2 flat washers and 1 lock nut). Repeat for the second Glider End. (fig. 40.1) B: Install 2 Glider Rope with Chains into each Glider End using 2 - 5/16” Flat Washers and 1 Lock Nut per rope. (fig. 40.1) Glider may not be as shown. Glider Rope Appearance may vary. Fig. 40.1 and Chain Fig. 40.1 Glider Rope and Chain 5/16 Flat Washer-Zinc 5/16 Flat Washer-Zinc 5/16 Flat Washer-Zinc 5/16 Flat 5/16 Lock Washer-Zinc Nuts...
  • Page 74 Step 41: Attach Glider and Swings If Bolt protrudes Warning! Check entire play centre for beyond T-Nut bolts protruding beyond T-Nuts. Use extra washers to eliminate this condition. Use an extra Flat Washer A: Connect the assembled Glider to the Glider Hangers previously installed. (fig. 41.1) B: Attach 2 Belt Swings to the Bolt-Thru Swing Hangers.
  • Page 75 I.D. Plaque Attach with screws provided to a location on your set that is easily seen and read by a supervising adult. Hardware Other Parts #8 x 1/2” Pan Screw 1 x KidKraft I.D. Plaque...
  • Page 76 Would you recommend the purchase of our products to friends and family? Comments: MAIL TO: Fill out your registration card online at KidKraft https://prdregistration.kidkraft.com/ 4630 Olin Road Dallas, TX 75244 United States KidKraft would like to say Thank You for Attention: Customer Service your time and feedback.

This manual is also suitable for:

F270855