Table of Contents
Advertisement
Quick Links
1.
OVERVIEW.......................................................................................................................................... 1
2.
INSTALLATION................................................................................................................................... 3
3.
SPECIFICATIONS............................................................................................................................... 4
3.1. RF INPUT ................................................................................................................................... 4
3.2. RF OUTPUT................................................................................................................................ 4
3.3. ELECTRICAL ............................................................................................................................. 4
3.4. PHYSICAL (NUMBER OF SLOTS)............................................................................................ 5
4.
STATUS INDICATORS AND DISPLAY .............................................................................................. 6
4.1. CARD EDGE LEDS .................................................................................................................... 6
4.2. DOT-MATRIX DISPLAY ............................................................................................................. 7
4.2.1. Setting the Input RF Alarm Threshold Levels ....................................................................... 9
4.2.2. Setting the Gain Mode .......................................................................................................... 9
4.2.3. Setting the Gain .................................................................................................................. 10
4.2.4. Setting the AGC RF Output Target Level............................................................................ 10
4.2.5. Setting the Slope Correction Level...................................................................................... 10
4.2.6. LNB Voltage Level .............................................................................................................. 11
4.2.7. 22KHz Tone ........................................................................................................................ 12
4.2.8. LNB Current Threshold Levels............................................................................................ 12
4.2.9. Default Card-Edge Display.................................................................................................. 12
4.2.10. Setting the Display Orientation............................................................................................ 12
4.2.11. Displaying the RF Input Power............................................................................................ 13
4.2.12. Displaying the RF Input Alarm Thresholds.......................................................................... 13
4.2.13. Displaying the Gain Mode Setting....................................................................................... 13
4.2.14. Displaying the Gain Setting................................................................................................. 13
4.2.15. Displaying the AGC Output Power Target Level ................................................................. 14
4.2.16. Displaying the Slope Correction Level ................................................................................ 14
4.2.17. Displaying the LNB Voltage Level....................................................................................... 14
4.2.18. 22KHz Tone Status ............................................................................................................. 14
4.2.19. Displaying the LNB Current................................................................................................. 14
4.2.20. Displaying the LNB Current Threshold Level ...................................................................... 15
4.2.21. Displaying the Firmware Version ........................................................................................ 15
5.
JUMPERS AND USER ADJUSTMENTS .......................................................................................... 16
BY THE GLOBAL FRAME STATUS........................................................................................ 16
5.2. CONFIGURING THE MODULE FOR FIRMWARE UPGRADES ............................................. 17
7703PA, 7703PA-LNB, 7703PA-2 RF Amplifier with Slope Compensation
TABLE OF CONTENTS
Revision 1.0
7700 MultiFrame Manual
Advertisement
Table of Contents
Related Manuals for evertz 7700
Summary of Contents for evertz 7700
-
Page 1: Table Of Contents
7700 MultiFrame Manual 7703PA, 7703PA-LNB, 7703PA-2 RF Amplifier with Slope Compensation TABLE OF CONTENTS OVERVIEW............................1 INSTALLATION........................... 3 SPECIFICATIONS..........................4 3.1. RF INPUT ........................... 4 3.2. RF OUTPUT..........................4 3.3. ELECTRICAL ..........................4 3.4. PHYSICAL (NUMBER OF SLOTS).................... 5 STATUS INDICATORS AND DISPLAY ....................6 4.1. - Page 2 7700 MultiFrame Manual 7703PA, 7703PA-LNB, 7703PA-2 RF Amplifier with Slope Compensation 5.3. FACTORY AND BDM JUMPERS..................... 17 VISTALINK REMOTE MONITORING/CONTROL ................18 ® 6.1. WHAT IS V LINK ?......................18 ISTA ® 6.2. V LINK MONITORED PARAMETERS ................19 ISTA ®...
- Page 3 May 2010 Information contained in this manual is believed to be accurate and reliable. However, Evertz assumes no responsibility for the use thereof nor for the rights of third parties, which may be affected in any way by the use thereof. Any representations in this document concerning performance of Evertz products are for informational use only and are not warranties of future performance, either expressed or implied.
- Page 4 7700 MultiFrame Manual 7703PA, 7703PA-LNB, 7703PA-2 RF Amplifier with Slope Compensation This page left intentionally blank Revision 1.0...
-
Page 5: Overview
7700 MultiFrame Manual 7703PA, 7703PA-LNB, 7703PA-2 RF Amplifier with Slope Compensation OVERVIEW The 7703PA series provide amplification of RF signals in the satellite extended L-Band range. Adjustable slope compensation is included. Typical applications include amplification and slope compensation to boost weak signals, drive long coax runs or provide a high power signal for passive distribution systems. -
Page 6: Figure 1-1: 7703Pa, 7703Pa-Lnb, 7703Pa-2 Block Diagram
7700 MultiFrame Manual 7703PA, 7703PA-LNB, 7703PA-2 RF Amplifier with Slope Compensation Figure 1-1: 7703PA, 7703PA-LNB, 7703PA-2 Block Diagram Revision 1.0 Page - 2... -
Page 7: Installation
7700 MultiFrame Manual 7703PA, 7703PA-LNB, 7703PA-2 RF Amplifier with Slope Compensation INSTALLATION The 7703PA and 7703PA-LNB both come with a companion rear plate that has 2 BNC type 75 Ohm connectors (F type, 50 Ohm BNC and SMA connectors are optional). The 7702PA-2 comes with a companion rear plate that has 4 connectors. -
Page 8: Specifications
7700 MultiFrame Manual 7703PA, 7703PA-LNB, 7703PA-2 RF Amplifier with Slope Compensation SPECIFICATIONS 3.1. RF INPUT Number of Inputs: 7703PA: 7703PA-LNB: 7703PA-2P: BNC per IEC 61169-8 Annex A (F-Type, 50 Ohm BNC and SMA optional) Connector: 75Ω (50Ω optional) Impedance: 950-2150MHz with slope control... -
Page 9: Physical (Number Of Slots)
7700 MultiFrame Manual 7703PA, 7703PA-LNB, 7703PA-2 RF Amplifier with Slope Compensation 3.4. PHYSICAL (NUMBER OF SLOTS) 7700FR-C: 7800FR: 7701FR: Revision 1.0 Page - 5... -
Page 10: Status Indicators And Display
7700 MultiFrame Manual 7703PA, 7703PA-LNB, 7703PA-2 RF Amplifier with Slope Compensation STATUS INDICATORS AND DISPLAY 4.1. CARD EDGE LEDS Two large LEDs on the front of the board indicate the general health and alarm status of the module: This Green LED will be On when the module is operating properly and not extending MODULE OK: any alarms. -
Page 11: Dot-Matrix Display
7700 MultiFrame Manual 7703PA, 7703PA-LNB, 7703PA-2 RF Amplifier with Slope Compensation RF Input Power Channel 2 is less then the lower threshold setting or YELLOW greater then the upper threshold setting. RF Input Power Channel 2 is less then the lower threshold setting or greater then the upper threshold setting. - Page 12 7700 MultiFrame Manual 7703PA, 7703PA-LNB, 7703PA-2 RF Amplifier with Slope Compensation Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 BACK BACK 0 to -60 dBm Default: -60 dBm RFTH 0 to -60 dBm UPPR Default: 0 dBm...
-
Page 13: Setting The Input Rf Alarm Threshold Levels
7700 MultiFrame Manual 7703PA, 7703PA-LNB, 7703PA-2 RF Amplifier with Slope Compensation GAIN (visible in manual mode 0 to 31.5dB only) OUTL (visible 0 to -50dBm in AGC mode only) 0-15 LNBV (visible only on –LNB version) 22KT (visible only on –LNB... -
Page 14: Setting The Gain
7700 MultiFrame Manual 7703PA, 7703PA-LNB, 7703PA-2 RF Amplifier with Slope Compensation Channel 1 gain mode. CTRL Channel 2 gain mode. MODE CH1 / CH2 Enables Automatic Gain Control mode. Enables manual control. (default) 4.2.3. Setting the Gain Sets the fixed amount of applied gain. Visible in manual mode only. -
Page 15: Lnb Voltage Level
7700 MultiFrame Manual 7703PA, 7703PA-LNB, 7703PA-2 RF Amplifier with Slope Compensation 21 dB 15 dB 6 dB 0 dB 40 MHz 950 MHz 2150 MHz 0dB applied gain, 0dB applied slope 0dB applied gain, 6dB applied slope 0dB applied gain, 15dB applied slope... -
Page 16: 22Khz Tone
7700 MultiFrame Manual 7703PA, 7703PA-LNB, 7703PA-2 RF Amplifier with Slope Compensation 4.2.7. 22KHz Tone Enables the 22KHz tone on the LNB voltage output. Visible on -LNB CTRL versions only. The default setting is OFF. 22KT Enables the 22KHz tone. Disables the 22KHz tone. -
Page 17: Displaying The Rf Input Power
7700 MultiFrame Manual 7703PA, 7703PA-LNB, 7703PA-2 RF Amplifier with Slope Compensation 4.2.11. Displaying the RF Input Power The 7703PA detects the RF input power level and displays this on the four-digit card edge display. Note that this power level is a measure of the total composite signal power entering the card. -
Page 18: Displaying The Agc Output Power Target Level
7700 MultiFrame Manual 7703PA, 7703PA-LNB, 7703PA-2 RF Amplifier with Slope Compensation 4.2.15. Displaying the AGC Output Power Target Level Indicates the RF output power target in AGC mode. Visible in AGC mode STAT only. OUTL CH 1 / CH 2 Channel 1 AGC target. -
Page 19: Displaying The Lnb Current Threshold Level
7700 MultiFrame Manual 7703PA, 7703PA-LNB, 7703PA-2 RF Amplifier with Slope Compensation 4.2.20. Displaying the LNB Current Threshold Level Indicates the lower LNB current threshold level. STAT Indicates the upper LNB current threshold level. LNTH UPPR LWR / UPPR LNB current threshold range. -
Page 20: Jumpers And User Adjustments
7700 MultiFrame Manual 7703PA, 7703PA-LNB, 7703PA-2 RF Amplifier with Slope Compensation JUMPERS AND USER ADJUSTMENTS Toggle Switch LOCAL FAULT / MODULE OK RF Ch2 High RF Ch1 High RF Ch2 OK RF Ch1 OK RF Ch2 Low RF Ch2 Low... -
Page 21: Configuring The Module For Firmware Upgrades
5.3. FACTORY AND BDM JUMPERS When shipped from the Evertz facility, the FACTORY and BDM jumpers will not be installed. These jumpers should not be installed for any reason. If jumpers are on these positions they should be removed. -
Page 22: Vistalink Remote Monitoring/Control
ISTA ® VistaLINK is Evertz’s remote monitoring and configuration platform which operates over an Ethernet ® network using Simple Network Management Protocol (SNMP). SNMP is a standard computer network protocol that enables different devices sharing the same network to communicate with each other. -
Page 23: Vista Link ® Monitored Parameters
7700 MultiFrame Manual 7703PA, 7703PA-LNB, 7703PA-2 RF Amplifier with Slope Compensation 6.2. LINK MONITORED PARAMETERS ISTA ® The following parameters can be remotely monitored through the VistaLINK interface. ® Parameter Description A range of values describing received RF power at the input. -
Page 24: Vista Link ® Traps
7700 MultiFrame Manual 7703PA, 7703PA-LNB, 7703PA-2 RF Amplifier with Slope Compensation 6.4. LINK TRAPS ISTA ® The following traps can be controlled through the VistaLINK interface. Each trap will indicate a fault ® condition when its value is True. Trap Description Input power is above the threshold.
Need help?
Do you have a question about the 7700 and is the answer not in the manual?
Questions and answers