Table of Contents
Advertisement
8 CC-Link Data List
Signal
Name
Motor Revolutions / Output
RYB
Frequency Switch
RYC
Monitor Reference
RYD
Frequency Reference 1
RYE
Frequency Reference 2
RYF
Command Code Execute Request Request to execute the command code.
RY10 - 13
Reserved
RY14
Terminal S1 Function
RY15
Terminal S2 Function
RY16 - 19
Reserved
RY1A
Fault Reset
RY1B - 1F
Reserved
Note:
1. If making frequent setting changes, use RYD (Frequency Reference 1 flag) for setting the register. You can write the EEPROM to the
drive a maximum of 100,000 times. Do not use this write command frequently.
2. Although RYE and RYF are triggered by the rising edge of the signal, they are otherwise enabled depending on the value that is
input.
Drive → PLC
Signal
Name
RX0
Forward Run
RX1
During Reverse
1000-Series: Terminal M1-M2
Function
GA700, GA800: Multi-Function
RX2
Digital Output 1 Function
GA500: Terminal MA/MB-MC
Function
RX3
Speed Agree
RX4
During Stall Prevention
RX5
During Uv [Undervoltage]
1000-Series, GA500: Terminal P1
*1
Function
RX6
GA700, GA800: Multi-Function
Digital Output 2 Function
1000-Series, GA500: Terminal P2
*1
Function
RX7
GA700, GA800: Multi-Function
Digital Output 3 Function
RX8, 9
Reserved
RXA
CC-Link Option Fault
30
Sets data contents for the remote register RW
ON: Output Frequency
OFF: Motor revolutions
ON: Monitor data specified in the monitor code is set to remote register RW
Frequency set to remote register RW
Sets the frequency in the remote register RW
Reference 1] and as the drive's main frequency reference at the same time.
Note:
If the frequency reference is set to be provided by the keypad (i.e. b1-01 = 0
[Frequency Reference Selection 1 = Keypad]), then switching ON RYE changes the
frequency reference.
Multi-Function Input: H1-01 [Terminal S1 Function Selection]
Multi-Function Input: H1-02 [Terminal S2 Function Selection]
Resets a drive fault
Table 8.2 Remote I/O List (Drive → PLC)
ON: Forward Run Command Present (includes DC Injection Braking)
OFF: No Forward Run Command
ON: During Reverse
OFF: No Reverse Run Command (includes DC Injection Braking)
Multi-function output: H2-01
ON: Output frequency is between frequency reference and the detection width set to L4-
02 [Speed Agree Detection Width].
Multi-Function Output: H2-02
*1
Multi-Function Output: H2-03
*1
Communication error between drive and CC-Link device
Description
.
R1
becomes the operating frequency for the drive.
W1
to parameter d1-01 [Frequency
W1
-
-
-
Description
-
-
-
YASKAWA SIEP C730600 83E CC-Link Technical Manual
Comments (Default)
Disabled in V/f Control or PM
Open Loop Vector mode. RW
the output frequency.
When switching between
monitors using RYC (Monitor
Reference), RYC needs to be
.
R0
turned OFF and then back ON
again after the monitor code has
been changed.
When switching ON RYD, the
frequency in the remote register
RW
will always reflect the
W1
operating frequency for the drive.
All parameter settings are saved
when this flag is switched ON.
Triggered by the rising edge of
the signal.
Triggered by the rising edge of
the signal.
-
Function is disabled when for H1-
01 = 40 [Forward Run Command
= Forward RUN (2-Wire)].
Function is disabled when for H1-
01 = 41 [Forward Run Command
= Reverse RUN (2-Wire)].
-
-
-
Comments (Default)
-
-
1000-Series, GA700, GA800: H2-
01 = 0 [Term M1-M2 Function
Selection = During Run]
GA500: H2-01 = E [Term MA/
MB-MC Function Selection =
Fault]
-
-
-
1000-Series, GA700, GA800: H2-
02 = 1 [Term M3-M4 Function
Selection = Zero Speed]
GA500: H2-02 =0 [Terminal P1-
C1 Function Selection During
Run]
1000-Series, GA700, GA800: H2-
03 = 2 [Term M5-M6 Function
Selection = Speed Agree 1]
GA500: H2-03 = 2 [Terminal P2-
C2 Function Selection = Speed
Agree 1]
-
-
is
R1
Advertisement
Table of Contents
