Related Manuals for YASKAWA SI-P1/ V7
Summary of Contents for YASKAWA SI-P1/ V7
- Page 1 YASKAWA VS-606 V7 OPTION UNIT PROFIBUS-DP INTERFACE UNIT INSTRUCTIONS MODEL: SI-P1/V7 Upon receipt of the product and prior to initial operation, read these instructions thoroughly and retain them for future reference. YASKAWA MANUAL NO. TOBZ-C736-70.4B...
-
Page 2: Safety Information
PROFIBUS-DP slave. When the slave is registered in the GSD file in the PROFIBUS-DP master, the master also recognizes the SI-P1/V7 unit, and then the SI-P1/V7 can be used in the registered slave. To obtain the GSD file, please contact your Yaskawa representative. - 3 -... -
Page 3: Outline Of Product
Modular Plug (CN1) Optional (CN2) Connector 5.5 m Terminal Address Switch1 Block Termination Resistor Selector Address Switch2 Ground Terminal Switch Front of the SI-P1/V7 Unit Rear of the SI-P1/V7 Unit Fig. 1 PROFIBUS-DP Communications Interface Unit SI-P1/V7 1 OUTLINE OF PRODUCT The PROFIBUS-DP Communication Interface Unit SI-P1/V7 is an option unit that can be mounted on the VS-606V7 Inverter and used for communications with the PROFIBUS-DP master. -
Page 4: Parts List
Are any parts missing? Check the parts list (see 2.2.) Contact your Yaskawa representative immediately if any problem should be found concerning the shipment. 2.1 Nameplate The following diagram shows the nameplate on the side of the SI-P1/V7 Unit. PROFIBUS-DP Communications... -
Page 5: Installation
3 INSTALLATION The SI-P1/V7 Unit is mounted with the digital operator and the front cover of the inverter removed. To mount the unit, do the following. 1) Turn OFF the inverter’s power supply and remove the digital operator and the front cover and then wait one minute after all the LEDs are turned OFF. - Page 6 4 INTERCONNECTION Fig.2 shows the interconnection between the inverter, the SI-P1/V7 unit and the PROFIBUS-DP master. Inverter Motor 3-phase power supply PROFIBUS-DP master VS-606 V7 SI-P1/V7 unit (50P) 9-pin connection terminals D-SUB (50P) RxD/TxD-N RxD/TxD-N RxD/TxD-P RxD/TxD-P Shield Fig. 2 Interconnection between Devices : Precautions on Wiring NOTE (1) Separate the wiring for SI-P1/V7 communications from the main circuit wiring or other power...
- Page 7 (2) To wire the PROFIBUS-DP master and the terminal for the SI-P1/V7 unit, use a shielded twisted-pair cable and do the following. 1) The following chart shows the applicable cable sizes for the terminal block JP3. [ Terminal: MINI COMBICON series, made by Phoenix Contact Co., Ltd. ] ［mm ］...
- Page 8 GSD file version is different. (Previous GSD file:Revision=Version1.0 → New GSD file:Revision=Version3.1) Contact your Yaskawa representative to get the new GSD file for SI-P1/V7 unit. The new GSD file (Version3.1) for SI-P1/V7 unit is applicable to both the SI-P1/V7 unit and the SI-P/V7 unit.
- Page 9 No.18 Xizang Zhong Road. Room 1702-1707, Harbour Ring Plaza Shanghai 200001, China Phone 86-21-5385-2200 Fax 86-21-5385-3299 YASKAWA ELECTRIC (SHANGHAI) CO., LTD. BEIJING OFFICE Room 1011A, Tower W3 Oriental Plaza, No.1 East Chang An Ave., Dong Cheng District, Beijing 100738, China...