Advertisement
No.
Parameter
1-3
SIZE
1-4
ROT X
ROT Y
1-5
PERS
2-1
ASPECT X
2-2
ASPECT Y
2-3
ASPECT R
a) When the [ROT X] button is selected
b) When the [ROT Y] button is selected
For details about selecting the rotation direction, see
"Rotating a key (key control block)" (page 139).
Reducing, enlarging, moving, and rotating
keys (device control block)
Switch the device control block to resizer operation mode
to operate a two-dimensional transform.
1
Press the [M/E 1] button.
The [M/E 1] button is lit green, and the device control
block switches to M/E-1 resizer operation mode.
You can select multiple switcher banks. The first
selected button becomes the reference channel, and is
lit green. Subsequent selected buttons are lit amber.
2
Press the [K1RSZ] button.
The [K1RSZ] button is lit green, and key 1 becomes
the target of resizer operations.
You can select multiple keys. The first selected
button becomes the reference channel, and is lit
green. Subsequent selected buttons are lit amber.
3
Press the [RSZR ON] button.
The [RSZR ON] button turns on and the resizer is
enabled.
4
Transform the key.
To change the aspect ratio of a key
Press the [ASP PERS] button, turning it on, and
adjust the setting values using the trackball/Z-ring.
To change the position and size of a key
Press the [LOC SIZE] button, turning it on, and adjust
the setting values using the trackball/Z-ring.
Adjustment
Size of key
a)
Rotation around X-axis
b)
Rotation around Y-axis
Viewpoint position
(perspective)
Aspect ratio in horizontal
direction
Aspect ratio in vertical
direction
Simultaneous adjustment of
aspect ratio in horizontal
direction and vertical
direction
To change the rotation and viewpoint position of a
key
Press the [ROT] button, turning it on, and adjust the
setting values using the trackball/Z-ring.
To finely adjust the setting values of parameters
Press the [FINE] button, turning it on.
The adjustment mode switches to fine mode, enabling
fine adjustment of setting values using the trackball/
Z-ring.
To restrict the parameters targeted by the
operation
Press the [X] button, [Y] button, or [Z] button,
turning it on.
This enables operation only for the selected axis
using the trackball/Z-ring.
Transforming an image using trackball/Z-ring
operations
You can transform an image as follows using trackball/Z-
ring operations for each two-dimensional transform.
Button
Trackball
Horizontal
direction
ASP
Change
PERS
aspect ratio in
X-axis
direction
LOC
Movement in
SIZE
X-axis
direction
ROT
Rotation
around Y-axis
Device control block display
In the device control block of the ICP-X7000, the display
shows the following information.
• Reference switcher bank name: M/E1 to M/E5, P/P
• Reference resizer name: KEY1 RSZR to KEY8 RSZR
• Selected parameter name: ASP, LOC SIZE, ROT
PERS, BDR, CROP
• X-axis, Y-axis, and Z-axis settings (four edge settings
for crop)
To adjust the setting values of parameters using
the numeric keypad control block
You can press the [X] button, [Y] button, or [Z] button in
the device control block to display the name and value of
parameters on the display of the numeric keypad control
block and then set the X-axis, Y-axis, and Z-axis
parameters. Enter a value in the numeric keypad area and
press the [ENTER] button to apply the setting.
138
Z-ring
Vertical
direction
Change
Simultaneous
aspect ratio in
change aspect
Y-axis
ratio in X-axis
direction
direction and
Y-axis
direction
Movement in
Scaling
Y-axis
(shrink/
direction
magnify)
Rotation
Change
around X-axis
distance from
viewpoint
position
Advertisement
Chapters
