MacDon M155 Unloading And Assembly Instructions page 45

C x x x || A C T I V A T E
L1
M x x x ||
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
C x x x || F O R C E
L1
M x x x ||
L2
L1
L2
L2
L2
L2
L2
L2
L2
L2
L2
L2
L2
L2
L2
L2
L1
L2
L1
L2
Form 169540
UNLOADING AND ASSEMBLY
F U N C T I O N S ?
N O / Y E S
C x x x || A C T I V A T E
M x x x || H E A D E R
C x x x || A C T I V A T E
M x x x ||
R E E L
C x x x || A C T I V A T E
M x x x || H D R
T I L T
C x x x || A C T I V A T E
M x x x || K N I F E
D R I V E
C x x x || A C T I V A T E
M x x x || D R A P E R / A U G E R
C x x x || A C T I V A T E
M x x x ||
R E E L
C x x x || A C T I V A T E
M x x x ||
D W A D R I V E
C x x x || A C T I V A T E
M x x x ||
N O / Y E S
C x x x || T O
A C T I V A T E
M x x x || P R E S S
A N D
C x x x || P U R G E
C Y C L E
M x x x || P R E S S
A N D
C x x x || P U R G E
C Y C L E
M x x x ||
C x x x || P U R G E
C Y C L E
M x x x ||
N O E X I T
C x x x || E X I T
F U N C T I O N
M x x x ||
N O / Y E S
H E A D E R T Y P E ?
N O / Y E S
C x x x || S E L E C T
H E A D E R
M x x x ||
D I S C
M x x x ||
S K
M x x x ||
D K
M x x x ||
G R A S S
M x x x ||
2 0 F T
M x x x ||
2 5 F T
M x x x ||
3 0 F T
M x x x ||
3 5 F T
M x x x ||
1 5 F T
M x x x ||
2 0 F T
M x x x ||
2 5 F T
M x x x ||
3 0 F T
M x x x ||
3 5 F T
M x x x ||
4 0 F T
C x x x || E X I T
H E A D E R
M x x x ||
N O / Y E S
C x x x || E X I T
D I A G N O S T I C S ?
M x x x ||
N O / Y E S
F O R C E
F U N C T I O N S ?
D O W N / U P
F U N C T I O N S ?
D O W N / U P
F U N C T I O N S ?
I N / O U T
F U N C T I O N S ?
O N
F U N C T I O N S ?
O N
F U N C T I O N S ?
F O R E / A F T
F U N C T I O N S ?
O N
H Y D P U R G E ?
P U R G E
H O L D
S T A R T E D
H O L D
E N D E D
E N D E D
Y E S
M E N U ?
E X I T
T Y P E
H E A D E R
A U G E R
A U G E R
S E E D
S K D R A P E R
S K D R A P E R
S K D R A P E R
W
S K D R A P E R
D K D R A P E R
D K D R A P E R
D K D R A P E R
D K D R A P E R
D K D R A P E R
D K D R A P E R
T Y P E ?
END
45
If "NO" then jump to:
H E A D E R T Y P E ?
For diagnostic purposes each header function
can be activated by using the "arrow" keys on
the CDM. When "SELECT" is pressed the
program will go to the next function that can be
activated.
If a disk header is detected then the
nomeclature should read: DISC DRIVE instead
of KNIFE DRIVE.
PWM OPERATION: If the HAZARD switch is
pressed instead of the TURN SIGNAL switch
the GSL will operate the PWM valve (HAZARD
sw must be held) and the PWM value will reset
to zero when released.
The DWA menu selection should only be
available if the DWA INSTALLED? is set to
YES.
ACTIVATE HYD PURGE - This is to allow the
operator to purge the air from a new or
changed pump system.
Pressing and holding the right hand "arrow"
button activates a predetermined timed purge
cycle. Releasing pressure on the switch or a
completed cycle (timed out) will jump to the
PURGE CYCLE ENDED menu selection.
If "NO" then jump to:
H E A D E R D O W N / U P
If "NO" then jump to:
D I A G N O S T I C S ?
This allows the operator to select or "force" a
header ID configuration if a "NO HEADER" ID
is being read by the control system. The
header type will revert back to "NO HEADER"
every time the ignition is cycled.
When "SELECT" is pressed the program goes
to the EXIT HEADER TYPE? menu selection.
If "NO" then jump to:
F O R C E H E A D E R
If "NO" then jump to:
D I A G N O S T I C M O D E ?
T Y P E ?
Revision B