MacDon M155 Unloading And Assembly Instructions page 43

C x x x || H D R
L1
M x x x || E X T E N D
L2
C x x x || C A L I B R A T I N G
L1
M x x x || E X T E N D
L2
M x x x || E X T E N D
L2
C x x x || C A L I B R A T I N G
L1
M x x x || R E T R A C T
L2
M x x x || H D R
L2
C x x x || T O
L1
M x x x ||
L2
M x x x ||
L2
M x x x ||
L2
M x x x || E X I T
L2
C x x x || C A L I B R A T I N G
L1
M x x x || P R E S S
L2
C x x x || C A L I B R A T I N G
L1
M x x x || F L O A T
L2
M x x x || F L O A T
L2
C x x x || C A L I B R A T I N G
L1
M x x x || F L O A T
L2
M x x x || H D R
L2
C x x x || T O
L2
M x x x ||
L2
M x x x ||
L2
M x x x ||
L1
M x x x || E X I T
L2
||
L1 C x x x D I A G N O S T I C
||
L2 M x x x
C x x x || V I E W
L1
M x x x ||
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
Form 169540
UNLOADING AND ASSEMBLY
T I L T S E N S O R
T L T T O
T I L T
T I L T
T I L T
T I L T
T I L T
T I L T C O M P L E T E
C A L I B R A T E
H E A D E R H E I G H T
H E A D E R T I L T
H E A D E R F L O A T
C A L ? N O / Y E S
F L O A T
F L T + T O
F L O A T
( + )
( + )
F L O A T
( - )
F L O A T C O M P L E T E
C A L I B R A T E
H E A D E R H E I G H T
H E A D E R T I L T
H E A D E R F L O A T
C A L ? N O / Y E S
M O D E ?
N O / Y E S
E R R O R C O D E S ?
N O / Y E S
C x x x || V I E W
T R A C T O R
||
M x x x ||
N O / Y E S
1 || 1 2 3 4 . 5
H R S
||
4 7 || S E N S O R
E V O L T S
2 || 1 2 3 0 . 5
H R S
||
7 1 || L O W
E H Y D R A U L I C
C x x x || E X I T
T R A C T O R
M x x x ||
N O / Y E S
C x x x || V I E W
E N G I N E
M x x x ||
N O / Y E S
1 || 1 2 3 4 . 5
H R S
||
4 4 9 || F U E L
P R E S S U R E
C x x x || E X I T
E N G I N E
M x x x ||
N O / Y E S
C x x x || E X I T
E R R O R
M x x x ||
N O / Y E S
C A L The display will indicate the sensor being calibrated. The
operator will be prompted to extend the header tilt and HOLD
S T A R T
will flash until the system has completed reading in the signal
with the header tilt fully extended. HOLD will change to DONE
H O L D
D O N E
When the header tilt extend is done, the CDM will prompt the
user to press the header tilt retract. COMPLETE (with buzzer)
H O L D
will flash on the screen for 2 seconds when the calibration is
S E L E C T
The operator can select any of the three items requiring
calibration (or exit the CAL menu) by using the turn signal
switches to cycle through the choices. Pressing SELECT will
take the operator to the calibration menu for that particular
The display will indicate the sensor being calibrated. The
operator will be prompted to press the float (+) and HOLD will
S T A R T
flash until the system has completed reading in the signal with
the header float fully extended. HOLD will change to DONE
H O L D
D O N E
When the header float (+) is done, the CDM will prompt the
user to press the header float (-). COMPLETE (with buzzer)
H O L D
will flash on the screen for 2 seconds when the calibration is
S E L E C T
Select any of the sensors by using the turn signal switches to
cycle through the choices. Pressing SELECT will take the
operator to the calibration menu for that particular sensor. NO
is the default for EXIT CAL?. If "NO" then jump to:
T O C A L I B R A T E
If "NO" then jump to:
T R A C T O R S E T U P ?
E N T E R
C O D E S ?
1 2 3
L O W
1 2 3
O I L
C O D E S ?
C O D E S ?
1 2 3
H I G H
C O D E S ?
C O D E S ?
43
(with buzzer).
finished.
sensor.
(with buzzer).
finished.
S E L E C T
If "NO" then jump to:
S E N S O R S E T U P ?
If "NO" then jump to:
V I E W E N G I N E C O D E S ?
The last 10 distinct error codes are stored
along with the code #, Exxx, engine hours and
number of occurrences. The "arrow" keys are
used to cycle between codes.
If "NO" then jump to the first error code logged.
If "NO" then jump to:
E N T E R S E N S O R
The last 10 distinct error codes are stored.
If "NO" then jump to the first engine error code
logged.
If "NO" then jump to:
V I E W T R A C T O R
(continued next page)
S E T U P ?
C O D E S ?
Revision B