MacDon M155 Unloading And Assembly Instructions page 40

IMPORTANT: ENGINE MUST BE RUNNING TO CALIBRATE SENSORS
For M155 with 4 cylinder Cummins, second line software version code displays as Mxxx.
For M205 with 6 cylinder Cummins, second line software version code displays as Xxxx.
||
L1 C x x x T R A C T O R
||
L2 M x x x
C x x x || S E T
L1
M x x x ||
L2
C x x x || K N I F E
L1
M x x x ||
L2
or
C x x x || D I S C
L1
M x x x ||
L2
C x x x || O V E R L O A D
L1
M x x x ||
L2
C x x x || H E A D E R
L1
M x x x ||
L2
M x x x ||
L2
C x x x || R E T U R N
L1
M x x x ||
L2
M x x x ||
L2
C x x x || A U T O
L1
M x x x ||
L2
M x x x ||
L2
C x x x || D W A
L1
M x x x ||
L2
L1
L2
L1
L2
C x x x || T I L T
L1
M x x x ||
L2
C x x x || D I S C
L1
M x x x ||
L2
C x x x || H D R
L1
M x x x ||
L2
C x x x || H A Y
L1
M x x x ||
L2
C x x x || A U G E R
L1
M x x x ||
L2
M x x x ||
L2
C x x x || S E T
L1
M x x x ||
L2
M x x x ||
L2
M x x x ||
L2
M x x x ||
L2
M x x x ||
L2
C x x x || S E T
L1
M x x x ||
L2
Form 169540
UNLOADING AND ASSEMBLY
DETAILED PROGRAMMING INSTRUCTIONS
Programming Menu Flow Chart
S E T U P ?
N O / Y E S
K N I F E S P E E D ?
1 2 0 0 S P M
O V E R L O A D
1 0 0 0 S P M
O V E R L O A D
2 0 0 0 R P M
P R E S S U R E ?
4 0 0 0 P S I
I N D E X
R E E L & C O N V E Y O R
R E E L O N L Y
T O C U T
H E I G H T & T I L T
H E I G H T O N L Y
R A I S E H E I G H T ?
- 4 . 0
- O F F
I N S T A L L E D ?
N O / Y E S
C x x x || S W A P
D W A
M x x x ||
N O / Y E S
C x x x || D W A
A U T O
M x x x ||
N O / Y E S
C Y L I N S T A L L E D ?
N O / Y E S
B L K I N S T A L L E D ?
N O / Y E S
C U T W I D T H ?
2 0 . 5 F E E T
C O N D I T I O N E R ?
N O / Y E S
H D R R E E L
R P M / M P H
R P M / K P H
T I R E S I Z E ?
1 8 . 4 X 2 6 T U R F
1 8 . 4 X 2 6 B A R
2 3 . 1 X 2 6 T U R F
6 0 0 - 6 5 R 2 8
5 8 0 / 7 0 R 2 6
E N G I N E I S C
N O / Y E S
If "NO" then jump to:
C A B D I S P L A Y
When the programming mode is entered the
header ID will be displayed on the top line of
S P D ?
the CDM using the last 4 display positions.
S P D ?
Pressing "SELECT" will go to the next line 1
(L1) menu selection. The turn signal "arrow"
keys are used to change the values. Pressing
M O D E ?
"PROGRAM" at any time will cancel the
programming mode / menus and return back
to the main operating displays.
M O D E ?
The auto raise setting can be changed from
+
4.0 (min.) to 10.0 (max.) in 0.5 increments
+
OFF disables the auto raise function.
H E A D E R
C O N T R O L S ?
U P / D O W N ?
ppears for M150/155 ONLY - If "NO" then jump t
H E A D E R
H E A D E R
0 1 0 1
Use the "arrow" keys to set the header cut
width. The header ID appears at the RHS.
DRAPER HEADER ONLY. Default will be
flashing. Use "arrow" keys to select.
S P D
Pressing "SELECT" will go to the next line 1
(L1) menu selection. The turn signal "arrow"
keys are used to change the values.
T U R F
R P M ?
S E T
40
S E T U P ?
If "NO" then jump to:
C U T W I D T H ?
Swaps the GSL reel fore / aft with the DWA console
controls. If NO jump to DWA AUTO UP & DOWN?
Enables the express up and down feature with the
header RTC. If NO jump to HEADER CUT WIDTH?
C U T W I D T H ?
If "NO" then jump to:
C U T W I D T H ?
AUGER HEADER ONLY
For IMPERIAL display.
For METRIC display.
If "NO" then jump to:
C O N T R O L L O C K S ?
(continued next page)
Revision B