Jeep COMPASS Owner's Handbook Manual
  1. Manuals
  2. Brands
  3. Jeep Manuals
  4. Automobile
  5. Compass
  6. Owner's handbook manual

Jeep COMPASS Owner's Handbook Manual

Hide thumbs Also See for COMPASS:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
Table of Contents

Advertisement

Quick Links

COMPASS
OWNER HANDBOOK

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the COMPASS and is the answer not in the manual?

Questions and answers

Keith D Jones Jones
April 18, 2025

need 2022 YEAR MANUEL

0
1 comments:
Mr. Anderson
May 9, 2025

The 2022 Jeep Compass owner's manual is an online resource that provides information about the vehicle’s capabilities, maintenance schedule, and features. It includes video tutorials, warranty details, and guidance on using systems like Uconnect and 4x4. It also outlines service intervals, such as oil changes every 20,000 km or 1 year, brake fluid replacement based on time, and Uconnect Box battery replacement every 5 years. Users can access it by signing in and adding their vehicle to view all relevant details.

This answer is automatically generated

0

Subscribe to Our Youtube Channel

Related Manuals for Jeep COMPASS

Summary of Contents for Jeep COMPASS

  • Page 1 COMPASS OWNER HANDBOOK...
  • Page 3 Warranty Certificate and details of the terms and conditions for the maintenance of the vehicle. We are confident that these will bring you closer to your new car and make you appreciate the assistance provided by the Jeep team. Enjoy reading. Happy driving! ATTENTION All the versions of the Jeep Compass are described in this Owner Handbook.
  • Page 4 ELECTRICAL ACCESSORIES If, after buying the car, you decide to add electrical accessories (with the risk of gradually draining the conventional battery), contact a Jeep Dealership. They can calculate the overall electrical requirement and check that the car's electric system can support the required load.
  • Page 5 SCHEDULED SERVICING Correct maintenance helps to preserve the vehicle's performance and safety features, respect for the environment and low operating costs over time. ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles. This vehicle has a higher ground clearance and has a higher center of gravity compared to many other vehicles for transporting passengers, so that it allows a better performance to be reached in a wide range of off-road applications.
  • Page 6 USE OF THE OWNER HANDBOOK OPERATING INSTRUCTIONS Each time an instruction is given that concerns direction (left/right or forward/backward), it is written to be read from the perspective of an occupant in the driver's seat. If a direction is written from a different perspective, it will be specified as such in the text as appropriate. The figures in the Owner Handbook are provided by way of example only: this might imply that some details of the image do not correspond to the actual arrangement of your car.
  • Page 7    SYMBOLS Some car components have colored labels with symbols indicating precautions to be observed when using this component. See below for a brief description of each symbol summarising the contents herein. Always take great care to all warnings herein. J0A2300 High-voltage components On the high-voltage components of the vehicle, there are plates with specific symbols.
  • Page 8 If after buying the car, you decide to install electrical accessories that require a permanent electrical supply (e.g. radio, satellite anti-theft system, etc.) or accessories that in any case burden the electrical supply, contact a Jeep Dealership, whose personnel will check whether the electrical system of the car is able to withstand the load required, or whether it needs to be integrated with a more powerful battery.
  • Page 9 KNOWING YOUR CAR KNOWING THE INSTRUMENT PANEL SAFETY STARTING AND DRIVING IN CASE OF EMERGENCY SERVICING AND MAINTENANCE TECHNICAL SPECIFICATIONS MULTIMEDIA CONTENTS...

  • Page 11: Table Of Contents

    KNOWING YOUR CAR In-depth knowledge of your new car DASHBOARD ..... 10 starts here. PLUG-IN HYBRID VERSION The handbook you are reading will tell OPERATING PRINCIPLE .

  • Page 12: Dashboard

    DASHBOARD Left-hand drive version   5520624D 1. Headlight switch 2. Multi-function control stalk (headlights) 3. Instrument panel 4. Windscreen wiper stalk 5. Buttons (Emergency lights, ParkSense system, Active ParkSense system, LaneSense system, ESC system, eCoasting mode) and Uconnect™system 6. Climate control system 7. Driving assistance systems (Cruise Control, Adaptive Cruise Control, Speed Limiter, Intelligent Speed Assist) 8.
  • Page 13 Right-hand drive version   5520854D 1. Headlight switch 2. Multi-function control stalk (headlights) 3. Instrument panel 4. Windscreen wiper stalk 5. Buttons (Emergency lights, ParkSense system, Active ParkSense system, LaneSense system, ESC system, eCoasting mode) and Uconnect™system 6. Climate control system 7. Driving assistance systems (Cruise Control, Adaptive Cruise Control, Speed Limiter, Intelligent Speed Assist) 8.

  • Page 14: Plug-In Hybrid Version Operating Principle

    1) 2) 3) 4) 5) 6) electric motor for a certain distance as HYBRID SYSTEM EQUIPMENT long as the high-voltage battery permits Compass Plug-in hybrid is a P-HEV (Plug- 1) 2) in Hybrid Electric Vehicle). The car is equipped with a sealed high- For more information on the "e-SAVE"...
  • Page 15 To ensure that the lithium ion battery is into contact with bracelets, necklaces or contact a Jeep Dealership. maintained properly over time, the car any metal objects worn. must not be exposed to temperatures 4) Do not open, modify or remove the below -10°C and above 40°C for...

  • Page 16: Operating Mode

    OPERATING MODE "ELECTRIC" MODE the conditions are right to enable it, including: The "ELECTRIC" operating mode can (Plug-in Hybrid version) the state of charge of the high-voltage only be activated if the conditions listed While driving, three different operating battery is above 2%; above are met or until the driver requires modes can be selected by pressing the the temperature of the high-voltage...
  • Page 17 under certain conditions to protect the response in case of engine performance the LED located on the fig. 4/fig. 5 hybrid system. request. button flashes 3 times then turns off. The "e-SAVE" mode is never activated WARNING You cannot start the engine NOTE The "e-SAVE"...

  • Page 18: The Keys

    THE KEYS the energy needed to charge the high-voltage battery. "ELECTRIC mode": this operating mode activates the operation of the electric KEY WITH REMOTE CONTROL motor only. If high performance is required (pressing on the accelerator The metal insert of the key operates: pedal) the electric motor and the heat the ignition device;...
  • Page 19 Emergency key removal Unlocking the doors and the liftgate in the “Multimedia” section for further information. Press and release the button (2) fig. 6 or (1) fig. 7 on the key once to unlock REPLACING THE ELECTRONIC KEY BATTERY the driver's door or twice within five To replace the battery, proceed as seconds to unlock all doors and the follows:...
  • Page 20 WARNING When having the Sentry Key follows: immobilizer system serviced, bring all Remove the screw to separate the two the keys of the car with you to the Jeep Dealership. half-shells of the key, where provided; operate in the points indicated by the...

  • Page 21: Ignition Device

    They must be pressing the brake pedal (versions disposed of as specified by law in the with automatic transmission) or the special containers or taken to a Jeep clutch pedal (versions with manual Dealership, which will take care of their transmission);...
  • Page 22 (e.g. an attempted theft), wheel to the left and right to disengage The ignition device is provided with a have it checked over by a Jeep Dealership the lock. before driving again. safety mechanism. If the engine fails...

  • Page 23: Sentry Key

    1. Make sure that the ignition device of possible by the Jeep Dealership. The use of these devices could cause the car is in the STOP position. problems when starting and the 2.

  • Page 24: Premium Alarm

    PREMIUM ALARM Alarm deactivation case, switch of the security alarm of the car. The car alarm can be disarmed using any (where provided) of the following methods: If the security alarm of the car is on and The Premium alarm monitors the doors, the conventional battery is disconnected, Press the button on the key.

  • Page 25: Doors

    the key is physically removed from the For cars equipped with Keyless If the security alarm of the car is on and Enter-N-Go – Passive Entry, press the ignition device. the conventional battery is disconnected, START/STOP button of the ignition the security alarm will remain active 2.
  • Page 26 NOTES: The Passive Entry function may be programmed ON/OFF. If wearing gloves, or if it has rained and the door handle is wet, the activation sensitivity of the Passive Entry function may be reduced, resulting in a longer reaction time. If the car is unlocked by Passive Entry and no door is opened within 60 5520627D...
  • Page 27 IMPORTANT If “Unlock all doors A lock request is made using the key within 1.5 m of the liftgate, push the 1st press” is programmed all doors Passive Entry key enabled with a door electronic liftgate release to open with will unlock when you grab hold of the open.
  • Page 28 The car’s door and liftgate lock NOTES: This device fig. 20 can be engaged only with the doors open: With one of the Passive Entry keys of After pushing the door handle button, the car, within 1.5 m from the driver or wait for two seconds before you can position : device engaged (door locked);...

  • Page 29: Seats

    Manual adjustment (front seats) window, and open the door with the 25) Do not leave the key in or near the outside door handle. (where provided) car or in a place accessible to children and do not leave the ignition device of IMPORTANT Make adjustments while a car equipped with Keyless Enter-N-Go sitting in the seat you want to adjust...
  • Page 30 NOTE You may experience deformation Backrest angle adjustment in the seat cushion from the seat belt Use lever (3) fig. 21 to adjust the buckles if the seats are left folded for an backrest angle, accompanying it with the extended period of time. Simply return movement of the torso (operate the lever the seats to the open position.
  • Page 31 (where provided), longitudinal position operate the lumbar area device to obtain NOTE Saving a new memory profile will and angle of the backrest. maximum driving comfort. erase an existing profile from memory. Driver memory seat 1. Take the ignition device to the ENGINE position.
  • Page 32 Entry key fob to Memory” paragraph in NOTE The key can be excluded from the Push the switch once to turn the HI this chapter. memory settings by first pressing the setting on (High level). button (S) and then the button on the Press the button a second time to...
  • Page 33 Front ventilated seats Rear armrest 31) Be sure everyone in your vehicle is in (where provided) (where provided) a seat and using a seat belt properly. 32) After releasing the adjustment lever, Tans are placed in the seat cushion and The backrest central part, once tilted, always check that the seat is locked on backrest to suck air out of the passenger...

  • Page 34: Head Restraints

    HEAD RESTRAINTS REAR HEAD RESTRAINTS heater. The heat could cause burns even (adjustments) at a low temperature, especially when used for long periods of time. 43) 44) 45) Upward adjustment: raise the head 40) Do not place objects on the seat or on restraint until it clicks into place.

  • Page 35: Steering Wheel

    STEERING WHEEL before starting to drive normally. Re-fit function can be programmed so that they the rods of the head restraints in their are activated during remote start. ADJUSTMENTS housings, holding buttons (1) pressed. This function can be programmed The steering wheel can be adjusted both Then, re-position the head restraints via the Uconnect system.

  • Page 36: Rear-View Mirrors

    or a steering wheel cover of any type and material, or the steering wheel resistance may overheat. REAR-VIEW MIRRORS Interior rear-view mirror Operate lever fig. 30 to adjust the mirror into two different positions: normal or anti-glare. 5520703D 5520644D The mirror is fitted with a safety device Folding mirrors NOTE The function is disabled when the that causes its release in the event of a...

  • Page 37: External Lights

    MULTIFUNCTION STALK Resetting the power folding exterior mirrors side mirror could cause you to collide You may need to reset the power folding The multifunction stalk (1) fig. 35 with another vehicle or other object. Use your inside mirror when judging the allows you to control the operation of mirrors if the following occurs: size or distance of a vehicle seen in the...
  • Page 38 Internal greeting lights the side lights remain on at a lower NOTES: brightness. The Auto Dim High Beams control (where provided) can be turned on or off using the warning light switches on in the Located under the exterior mirrors, they Uconnect™...
  • Page 39 LIGHTS-ON REMINDER When the system is on, the “Headlight With ignition device in the ENGINE time delay” feature is also on with (where provided) position, press button to switch the engine off. This means the headlights light on/off. If the headlights or side lights are on will stay on for up to 90 seconds after after the ignition device is in the STOP The rear fog light switches on only when...

  • Page 40: Interior Lights

    This is also covered by a specific WARNING rule of the highway code. 5520320D Contact a Jeep Dealership to have the To protect the conventional battery, the 53) The daytime running lights are an headlights properly adjusted. interior lights will turn off automatically...

  • Page 41: Windscreen Wiper/Rear Window Wiper

    WINDSCREEN Turn the dashboard dimmer control Sun visor orientation function upwards (3) in fig. 36to increase the (where provided) WIPER/REAR WINDOW dashboard brightness ONLY when the The sun visor orientation function makes WIPER side lights or headlights are on. the sun visor positioning more flexible to To ensure the best daytime visibility provide shelter from the sun.
  • Page 42 function: operation is limited to the With the ring (1) fig. 39 turned to will be disabled with the ignition device position HI or LO, the smart washing time for which the stalk is held in this in the STOP position. position.
  • Page 43 the automatic wiping function is Deactivation NOTE If automatic windscreen wiping restored. The failure of the sensor is mode is active and the sensor does not indicated by the symbol lighting detect water, the rear window wiper will It is possible to deselect the automatic up on the display.
  • Page 44 If operation is not subsequently restored, even after restarting the engine, contact a Jeep Dealership. 11) Do not operate the screen wiper with the blades lifted from the windscreen glass. 12) Do not activate the rain sensor when washing the car in an automatic car wash.

  • Page 45: Climate Control System Controls

    CLIMATE CONTROL SYSTEM CONTROLS The climate control system allows you to regulate the temperature, air flow, and direction of air circulating throughout the car. The controls are located on the centre dashboard fig. 41 and on the Uconnect™ displayfig. 42. 5520632D...
  • Page 46 Controls on Uconnect™ system display 5520741D...
  • Page 47 Description of the controls fan speed adjustment recirculation on/off; compressor on/off; A description of the controls on the Description SYNC function activation; climate conditioner front panel and The automatic dual zone climate control heated rear window the graphic buttons on the Uconnect™ system regulates the air temperatures activation/deactivation.
  • Page 48 compartment. It also manages the air started. To turn these functions off, ask maximum fan speed: level 7; minimum fan speed: level 1. recirculation system and the enabling for a numerical air temperature. the air conditioning compressor. Air distribution selection WARNING To restore automatic During automatic operation, you control of the fan speed after a manual...
  • Page 49 SYNC button possibility of the windows misting up manually set lower than speed 1 inside rapidly (especially if the climate (minimum). Press the Sync button on the Uconnect™ control system is off). system display to align the passenger WARNING With the compressor off, air side air temperature with that of the When the outside temperature is low, cannot be introduced to the passenger...
  • Page 50 sets fan speed according to the engine Uconnect™ display will also activate the Switching on the climate control system coolant temperature; defrost/demisting of the exterior mirrors. To switch on the climate control system directs air flow to windscreen and front in fully automatic mode press the AUTO WARNING Do not apply stickers to the side windows vents;...
  • Page 51 System maintenance In winter, the climate control system must be turned on at least once a month for about 10 minutes. Have the system inspected at a Jeep Dealership before the summer. GAS IDENTIFICATION LABEL (where provided) The label fig. 43 is applied onto the front end of the bonnet.
  • Page 52 Practical advice table CLIMATIC CONDITIONS SETTINGS Turn the air distribution control to , turn on the climate control system and set the fan to maximum speed. Open the windows for a Warm climate and very high passenger compartment temperature minute to let the hot air out. Adjust the controls as needed to achieve the desired comfort.

  • Page 53: Electric Windows

    ELECTRIC WINDOWS Resetting the automatic closing For partial window opening, press the function electric window button briefly and ELECTRIC WINDOWS release it when the window is in the If the "Automatic closing" function no desired position. longer works, you may have to perform The electric window controls on the To stop the window from going all a reset cycle.

  • Page 54: Electric Sunroof

    ELECTRIC SUNROOF with remote control), always remove the key from the ignition device to prevent (where provided) accidental operation of the electric The power sunroof switches are located windows from being a hazard for those between the sun visors on the overhead still on board.
  • Page 55 stop. This type of opening is referred to is released prior to the sunroof reaching and stops automatically. Push and as "express" operation. During express the vent position. release the switch again from the half opening, any movement of the sunroof open position and the sunshade will CLOSING switch will stop the sunroof.
  • Page 56 Wind effect automatically close both the sunroof WARNING and sunshade completely. This type The wind effect can be defined as of closing is referred to as "express" a feeling of pressure on the ears or 59) When leaving the car (equipped with operation.

  • Page 57: Bonnet

    side of the car to release the bonnet IMPORTANT completely. 14) Do not open the sunroof if a transverse roof rack is fitted. Do not open the sun roof if there is snow or ice on it: you may damage it. BONNET DOOR 63) 64)

  • Page 58: Boot

    perfectly closed, do not try to press the Emergency opening from the inside IMPORTANT bonnet down but open it and repeat the Proceed as follows: procedure. remove the parcel shelf (where 15) To prevent possible damage, do not provided); WARNING Always check that the bonnet slam the hood to close it.
  • Page 59 the switch on the overhead console (1) liftgate is locked. The liftgate must be fig. 53 (where provided) and the liftgate unlocked to open it using the external switch (2) fig. 54 (where provided) on handle. Push the button on the key the upper left trim.
  • Page 60 or closed manually. After detecting If the electronic liftgate release handle go to the rear of the car, in the centre numerous obstructions in a single open is pushed with the power liftgate is and about 50 cm from the liftgate; or close cycle, the liftgate will lock and opening, the liftgate motor will disengage move your foot under the bumper,...
  • Page 61 if the liftgate was stopped, another 1. Disconnect the two rods (1) fig. 56 Rear shelf pin movement of the foot reverses the that support the shelf at the eyelets. direction and opens it completely. You can activate/deactivate the automatic liftgate opening and closing function in “Hands Free”...
  • Page 62 5520341D 5520640D 5520573D Access to TireKit (or removal of Each of the rear seats can be folded wheel/space-saver wheel) down to extend the loading area. This WARNING function allows the load compartment Pull the load platform handle upward to to be extended without completely raise the load platform and gain access 68) Be careful not to hit objects on the eliminating space for passengers.

  • Page 63: Interior Fittings

    INTERIOR FITTINGS The central tunnel has a storage a sudden stop or accident, a tie-down compartment that can hold mobile could pull loose and allow the child seat Glove compartment phones, PDAs (Personal Digital to come loose. A child could be badly injured.
  • Page 64 These USB ports have a "Smart Charge" There may be a rear 12V socket (1) feature that allows you to charge your fig. 67 and a 12V to 230V voltage connected device for one hour until the converter (2) at the rear of the central engine is turned off.
  • Page 65 phase, this will automatically be WARNING Do not place contactless interrupted. cards (RFID), credit cards or metal objects in the charging compartment. The wireless charging system is enabled when the car is in running condition and Correct positioning of the mobile phone the conventional battery is sufficiently To start charging wirelessly correctly, charged.

  • Page 66: Roof Rack/Ski Rack

    For further to the cargo or your car. of its life and/or failure to start the information, contact a Jeep Dealership. 23) Load should always be secured engine. Additional roof racks do not increase the...

  • Page 67: Environmental Protection

    ENVIRONMENTAL is displayed, see contents of "Warning lights and messages" chapter in the PROTECTION SYSTEMS "Knowing the instrument panel” section. DIESEL PARTICULATE FILTER (DPF) PETROL VERSIONS The Diesel Particulate Filter is a The systems used for reducing petrol mechanical filter, integral to the exhaust engine emissions are: catalytic converter, system, that physically traps carbon lambda sensors, fuel evaporation control...
  • Page 68 Blank page...
  • Page 69 KNOWING THE INSTRUMENT PANEL This section of the handbook provides EOBD SYSTEM (European On all information that is useful for getting Board Diagnosis) ....68 to know, interpreting, and using the INSTRUMENT PANEL .

  • Page 70: Eobd System (European On Board Diagnosis)

    This check can also be carried out by the traffic police. WARNING After eliminating an anomaly, to check the system completely, a Jeep Dealership is obliged to run tests and,...

  • Page 71: Instrument Panel

    INSTRUMENT PANEL 3.5" instrument panel 5520342D...
  • Page 72 7" instrument panel 5520343D...
  • Page 73 7" instrument panel (Plug-in Hybrid version) HYBRID Range km/h READY 5299 5520842D...
  • Page 74 10.25" instrument panel 5520568D...
  • Page 75 Description of the instrument WARNING The illumination of the The indications next to the graphic scale panel instrument panel graphics may vary indicate the amount of fuel: according to version. F (Full) = full tank 1. Tachometer E (Empty) = empty tank. This indicates the engine speed NOTE The warning lights come on during expressed in rpm (rpm x 1000).

  • Page 76: Display

    The brightness of the instrument panel is Upper area of the display (1): external drive system, referred to the maximum adjusted depending on what the sensor temperature, compass indications, time. available power. detects. Central area of the display (2): The top half of the indicator refers to the speed, warning messages/any failure output power.
  • Page 77 (5) Digital coolant thermometer/symbol display area HYBRID km/h 5299 5520347D 5520844D Top left/centre/right area (1): compass, (1) Gear engaged external temperature, date, time, trip A (2) Speedometer trip B, speedometer (depending on the (3) State of charge of the high-voltage display customisation).
  • Page 78 fluctuate, dependent upon your personal driving style. GEAR SHIFT INDICATOR (where provided) The Gear Shift Indicator (GSI) system advises the driver to change gear through a special indication on the display. Through the GSI, the driver is informed that the gear change will allow a reduction in fuel consumption.
  • Page 79 FUEL ECONOMY (PLUG-IN HYBRID Speedometer: Press and release the AdBlue / DEF level (where provided) ® VERSIONS) (EXCLUDING 10.25" OK button to change the unit of measure (Diesel versions only) DISPLAY) from "km/h" to "mph" and vice versa; Service HYBRID INFO (PLUG-IN HYBRID Driver Assist: The screen provides Tyre pressure VERSIONS)
  • Page 80 Service increase. In this case, switch off the fig. 89. This displays the mileage and days since engine and contact a Jeep Dealership. the last servicing operation. The following submenus are available for the 10.25" display: 10.25” display submenu...
  • Page 81 Adaptive Cruise Control (ACC) menu Refer to the “Adaptive Cruise Control FUEL" disappears to give way to the new (where provided) (ACC)” chapter in the “Starting and range value. The value cannot be reset The current settings of the ACC system driving”...
  • Page 82 HYBRID INFO (PLUG-IN HYBRID VERSIONS) fig. 98 (7" display) or fig. 99 (10.25" (hybrid system information) display). This Menu item allows you to view Driving the car in optimal conditions information on the instrument panel is achieved when the letter "e" and the display concerning: graphic indication on the graphic bar are shown in green in the middle of the...
  • Page 83 J0B6042E 5520580D J0B6043E...
  • Page 84 highlighted on the display, fig. 102 (7” display)/ fig. 103 (10,25” display); if the high-voltage battery is"Power" the right side of the screen will be highlighted on the display, fig. 104 (7” display)/ fig. 105 (10.25” display). J0B6044E J0B6045E 5520581D Charge / Power 5520582D The "Charge / Power"...
  • Page 85 ("HYBRID" or "ELECTRIC" or "E-SAVE") HYBRID INFO by showing dedicated messages on the display. TRIP/INFO TRIP (PETROL/DIESEL VERSIONS) Press and release the button until the title of the Trip menu is shown on the instrument panel display. Press button to select Trip A or Charge / Power Trip B.
  • Page 86 (EXCLUDING 10.25" DISPLAY) the screen (where provided) Top left Press and release the button None until the title of the "STOP/START" menu Compass (default setting) is shown on the instrument panel display External temperature Date AUDIO Time Press and release the button until the title of the "AUDIO"...
  • Page 87 Units ParkSense system. Menu title Select “Units" to set the unit of Rear ParkSense Volume (where Compass measurement to use for displaying provided): this can be used to select External temperature various values. The possible options are: the beep volume provided by the rear...
  • Page 88 -) disappear from the instrument panel Lights and warning lights button is pressed on the key. The display. The compass will then work Select "Lights" to make the following options are "Off", "At first press" and "At normally. adjustments: second press".

  • Page 89: Trip Computer

    compensate for differences, providing an Seat Belt Reminder Trip B extremely accurate reading. Shows the total distance travelled for Disable SBR (Seat Belt Reminder): to Trip B since the last reset. enable or disable the SBR system. SETTINGS (10.25” DISPLAY) It indicates the average fuel Hill Start Assist Press and release the...

  • Page 90: Warning Lights And Messages

    The warning light or symbol should illuminate for approximately four seconds. They must then switch off if the parking brake is not engaged and there is no damage to the braking system. If it does not switch on, contact a Jeep Dealership.
  • Page 91 The warning light flashes quickly for approximately 15 seconds when the security device is enabled and it then flashes more slowly until the car is unlocked. ALTERNATOR FAILURE The switching on of the symbol with engine on corresponds to an alternator failure. Contact a Jeep Dealership as soon as possible. DOORS OPEN The symbol switches on when one or more doors are not completely shut.
  • Page 92 This symbol will illuminate to indicate low engine oil pressure. If the symbol switches on while driving, stop the car immediately, shut off the engine as soon as possible, and contact a Jeep Dealership. The symbol will appear together with an acoustic signal.
  • Page 93 Jeep Dealership. TRACTION BATTERY FAILURE (where provided) The symbol appears on the instrument panel display in case of traction battery failure. Contact a Jeep Dealership. HYBRID-ELECTRIC SYSTEM FAILURE (where provided) The symbol appears on instrument panel display in case of hybrid-electrical system failure. The display will also show a dedicated message.
  • Page 94 In this case the airbags or pretensioners may not be deployed in an impact or, in a lower number of cases, they may be deployed accidentally. Before continuing, contact a Jeep Dealership to have the system immediately checked.
  • Page 95 If the problem persists, contact a Jeep Dealership.
  • Page 96 Certain conditions, such as a loose or missing tank cap, poor quality fuel, etc., could cause the warning light to come on after starting the engine. Contact a Jeep Dealership if it does not go off after having adopted other driving styles. In most cases, the car can be driven normally without needing to be towed.
  • Page 97 Warning Light/Symbol What it means Low tyre pressure The warning light switches on and a message is displayed to indicate that the tyre pressure is lower than the recommended value and/or that slow pressure loss is occurring. In these cases, optimal tyre duration and fuel consumption may not be guaranteed.
  • Page 98 MIN and MAX marks on the reservoir itself. Also check visually for any fluid leaks. Contact a Jeep Dealership if the symbol comes on when the engine is started again.
  • Page 99 ACTIVE SPEED LIMITER FAILURE (where provided) The symbol switches on in the case of failure of the Active Speed Limiter device. Contact a Jeep Dealership as soon as possible to have the failure solved. DPF CLEANING (particulate trap) IN PROGRESS (diesel versions with DPF only) The symbol lights up fixed, or a message appears on the display, to notify the driver that the DPF system needs to eliminate captured pollutants (particulate) through the regeneration process.
  • Page 100 The water in fuel symbol indicates that water was detected in the fuel filter. If this symbol remains on, DO NOT start the car before you drain the water from the fuel filter to prevent engine damage and contact a Jeep Dealership.
  • Page 101 (where provided) The symbol switches on, along with a displayed message, in the case of Keyless Enter-N-Go system failure. Contact a Jeep Dealership as soon as possible. POSSIBLE ICE ON ROAD The symbol switches on (along with a dedicated message on the display) when the external temperature is lower or equal to 3°C.
  • Page 102 FUEL LEVEL SENSOR FAILURE (where provided) The symbol switches on (along with a message on the display) in the event of fuel lever sensor failure. Contact a Jeep Dealership as soon as possible. PEDESTRIAN ACOUSTIC SIGNALLING SYSTEM FAILURE (where provided) This symbol is shown on the instrument panel display in case of failure of the pedestrian acoustic warning.
  • Page 103 Jeep Dealership. HIGHWAY ASSIST SYSTEM FAILURE (where provided) The symbol appears in the event of a failure in the Highway Assist system. If the fault persists, contact the Jeep Service Network. TSR SYSTEM FAILURE (where provided) The symbol appears to indicate a Traffic Sign Recognition (TSR) system failure.
  • Page 104 The symbol is displayed when Autonomous Emergency Brake Control with obstacle sensor system is disabled. CRUISE CONTROL FAILURE (where provided) The symbol appears to indicate a Cruise Control system failure. If the fault persists, contact a Jeep Dealership. HIGH-VOLTAGE BATTERIES DISCONNECTED (where provided) The symbol appears if the high-voltage batteries are disconnected.
  • Page 105 29) Do not continue driving with one or more flat tires as handling may be compromised. Stop the vehicle, avoiding sharp braking and steering. If a tire puncture occurs, repair immediately using the dedicated tire repair kit and contact a Jeep Dealership as soon as possible.
  • Page 106 When the car is moving, the warning light or symbol goes out: if the warning light remains on with steady light or flashing light, contact the Jeep Dealership. ACTIVE SPEED LIMITER ACTIVATION (where provided) This symbol will light up when the active speed limiter is on and set to a specific speed.
  • Page 107 (regeneration in progress). If the green or white symbol does not turn on after pushing the relative button on the central tunnel, this indicates a system failure: in this case contact a Jeep Dealership.
  • Page 108 Warning Light/Symbol What it means INTELLIGENT SPEED ASSIST (ISA) ACTIVE (where provided) The symbol comes on in the event of a Intelligent Speed Assist system failure. Blue warning lights Warning light What it means MAIN BEAM HEADLIGHTS The warning light switches on when the main beam headlights are turned on. With the dipped beam headlights on, push the multifunction stalk forwards (towards the front of the car) to turn on the high beam headlights.
  • Page 109 If the green or white symbol does not turn on after pushing the relative button on the central tunnel, this indicates a system failure: in this case contact a Jeep Dealership. HILL DESCENT CONTROL (where present) System activation: symbol switched on continuously along with the display of a dedicated message.
  • Page 110 Grey symbols Symbol What it means CRUISE CONTROL ON (where provided) This symbol turns on with the base instrument panel when the Cruise Control is unavailable. Refer to the “Electronic Cruise Control” chapter in the “Starting and driving” section for further information. ACTIVE SPEED LIMITER READY (where provided) This symbol turns on with the basic instrument panel when the speed limiter is unavailable.
  • Page 111 The message is shown on the instrument panel display to indicate that 4WD is not available (e.g. including if there failure) the is no fuel) or to indicate an all-wheel drive system failure. If the fault persists, contact a Jeep Dealership. Warning messages...
  • Page 112 Hybrid-electric system This message appears on the instrument panel display if there is a fault in the hybrid-electric system. Contact a Jeep failure Dealership. The instrument panel display shows messages related to the operating mode selected ("HYBRID" or "ELECTRIC" or "e- Operating Mode SAVE").
  • Page 113 Jeep Dealership. a rate that the charging system cannot sustain. NOTES: The warning light or symbol come on to indicate a problem in the charging system.
  • Page 114 Blank page...
  • Page 115 SAFETY The following section is very important: PRECAUTIONS RELATING TO it describes the safety systems fitted THE HYBRID SYSTEM ..114 on the car and provides the necessary ACTIVE SAFETY SYSTEMS ..116 information on how to use them DRIVING ASSISTANCE correctly.

  • Page 116: Precautions Relating To The Hybrid System

    All high voltage wiring disconnection of the high-voltage battery harness is orange. If necessary, contact from the system are potentially toxic and the Jeep Dealership for servicing or repair work. NEVER touch the orange wiring flammable; harness. Severe injury or death by electric...
  • Page 117 HYBRID SYSTEM COMPONENTS ON CAR NOT TO TOUCH 5520723D Do not touch, disassemble, remove or replace the following components: 1. Front electric motor - 2. Charging control module - 3. Rear electric motor - 4. Charge module...

  • Page 118: Active Safety Systems

    High voltage components and cables on the braking system should be serviced as hybrid vehicles are electromagnetically The system intervenes during braking soon as possible by a Jeep Dealership to shielded. when the wheels are about to lock, restore the ABS function. If the warning...
  • Page 119 This system manages the distribution of brake of the spinning wheel. This will Contact a Jeep Dealership as soon as the braking torque between the front and allow more vehicle torque to be applied possible to have it repaired.
  • Page 120 under various driving conditions. The System Activation ESC system corrects for over-steering or NOTE Depending upon model and mode under-steering of the vehicle by applying of operation, the ESC system may have the brake of the appropriate wheel to multiple operating modes. assist in counteracting the over-steering System intervention or under-steering condition.
  • Page 121 When the car speed drops down below roll back from a complete stop while on than 48 km/h, go to a Jeep Dealership 64 km/h, the ESC systems turns off. an incline. If the driver releases the...
  • Page 122 HDC (HILL DESCENT CONTROL) activated if the automatic transmission RAB (Ready Alert Braking) SYSTEM SYSTEM is in the P (ParkReverse) or N (Neutral) It is a system that is activated position. For vehicles equipped with a automatically if the accelerator is (where provided) manual transmission, if the clutch is released quickly, with the aim of...
  • Page 123 the driver side door is closed. the car is on a descent with WARNING insufficient gradient, that is below 4% or a level surface, or is going uphill; 94) The ABS contains sophisticated the automatic transmission lever is in electronic equipment that may be P (“Park”) position.
  • Page 124 101) For the correct operation of the 105) In partial disengagement mode, the parking brake, turned the engine off and system, the tyres must of necessity be TCS component of the ESC system is engaged first gear, so that it is parked in the same make and type on all wheels, in disabled (except for the controlled slip safe conditions (for further information...

  • Page 125: Driving Assistance

    DRIVING ASSISTANCE approximately 3 m beyond the rear loads (refer to the "Weights" chapter in bumper of the car. The BSA system the "Technical Data" section). SYSTEMS monitors the detection zones on both 116) The TSC system cannot prevent BSA (Blind-Spot Assist) SYSTEM swerving for all trailers.
  • Page 126 The area on the rear bumper where speed of less than approx. 48 km/h with the radar sensors are located must respect to your car. remain free of snow, ice and dirt/road contamination so that the BSA system can function properly. Do not block the area of the rear bumper where the radar sensors are located with foreign objects (bumper stickers, bicycle racks, etc.).
  • Page 127 0304052893 0304052894 030405522 The BSA system is designed not to When RCP is on and the car is in 120) issue an alert on stationary objects reverse, the driver is alerted using both RCP (Rear Cross Path) function such as safety barriers, posts, walls, the visual and audible alarms, including This function helps the driver during foliage, berms, etc.
  • Page 128 "Blind Spot Alert", "Light/acoustic warning" shut off. Each time the car is started the mode previously stored mode will be recalled and used. When the system is enabled and presence of a vehicle in the blind spot is Sensors detected, a visual warning is sent to the If the system detects degraded concerned door mirror on the side of the performance due to contamination or...
  • Page 129 the car and is recognised as being aware additional assistance in braking stage, The function is not active at speed above of the situation and possible collision. where the driver does not brake at all 5 km/h. or not sufficiently in the event of a The car is equipped with the "creeping"...
  • Page 130 The system sensitivity setting is kept in Should the fault persist, contact a Jeep the memory when the engine is switched Dealership. off. System Fault Message...
  • Page 131 TPMS (Tyre Pressure Monitoring Pedestrian/cyclist detection The TPMS will warn the driver of a low System) tyre pressure if the tyre pressure falls While driving, when there is a risk of below the low-pressure warning limit for collision with a pedestrian or cyclist, the 127) 128) 129) 130) 131) any reason, including low temperature system will display the relevant warning...
  • Page 132 Seasonal temperature changes will pressure values appear in a different to approximately 1.9 bars, but the affect tyre pressure and the TPMS will colour (see example in fig. 125). warning light will still be on. In this monitor the actual tyre pressure in the situation, the warning light will turn OFF tyre.
  • Page 133 The car may need to be driven for up to Using rims /tyres not equipped with assemblies (road tyres) with wheel and 10 minutes above 24 km/h in order for TPMS sensors. tyre assemblies that do not have TPMS the TPMS to receive this information. sensors, such as when installing winter Space-saver wheel (where provided): the rim and tyre assemblies on your car.
  • Page 134 DRIVER ATTENTION ASSIST panel display up to the next time the always check your mirrors, look behind (DAA) SYSTEM engine is started/stopped. you and use your direction indicator If the driver ignores the warning before changing lanes. Failure to follow (where provided) these precautions could result in serious provided by the system and does not...
  • Page 135 (e.g. application of fillers or damage the TPMS sensor. prescribed value. Repeat the check when glues to remove scratches). Go to a Jeep the tyres are cold. Dealership for any operation of this type. 129) Should one or more wheels be fitted 37) Do not tamper with nor operate on without sensors (e.g.

  • Page 136: Pedestrian Acoustic Signalling System

    NOTE The system, operating only at equipment on others. If you are not sure, vehicle speeds below 20 km/h, is always contact a Jeep Dealership. active and cannot be deactivated. Important safety precautions Read the information given the following WARNING pages with the utmost care.
  • Page 137 Jeep Warnings on instrument panel warning. Once the SBR system warning Dealership. If the driver is unbuckled when the...
  • Page 138 The SBR system can be activated or your abdomen. resting on your neck. Correct tension deactivated by your Jeep Dealership. 3. Now, insert the fastening tongue will be ensured automatically by the NOTE If the SBR system has been (2) into the buckle (1) (fig.
  • Page 139 1. Position the fastening tongue as close anchoring in a lower position and if you as possible to the anchoring point. are taller than average, you will prefer the belt strap anchoring in a higher 2. At about 15 to 30 cm above the position.
  • Page 140 5. Arrange the waist belt section as low injury in the event of an accident is as possible, under your abdomen, and reduced for the mother and the unborn as snug as possible. To remove slack in child if they are wearing a seat belt the lap belt portion, pull up on the belt (fig.
  • Page 141 A single acoustic warning affected by water and/or mud, contact a Dashboard will sound to alert you if the warning Jeep Dealership to have it replaced. Driver and front passenger airbags light comes on again after initial start- Seat belt buckle seat button...
  • Page 142 If the icon on the display 166) 167) 168) 169) 170) Front airbags may not activate in the stays on while driving, go to a Jeep following situations: Driver and passenger front airbag functions Dealership immediately for the necessary...
  • Page 143 If any of the following Passenger's front airbag and child restraint seat, if available. Statistics on accidents occurs, have a Jeep Dealership service systems indicate that the rear seats offer greater the airbag system immediately: safety for children.
  • Page 144 Front passenger airbag deactivation Both warning lights stay off after you sound and the LED will light up for 4 start the car. To disable the front passenger airbag, to 5 seconds confirming the disabling Both warning lights come on as you access the instrument panel display of the passenger front airbag.
  • Page 145 NOTE If the passenger front airbag was shoulder protection. If your car is are not seated properly, or if items are previously DISABLED (OFF) it will equipped with front side airbags for positioned in the area where the SAB default to OFF and user will have to pelvis, chest and shoulder protection, inflates.
  • Page 146 The window bags deploy downward, Car damage by itself is not a good is appropriate, the rollover sensing covering the side windows. An inflating indicator of whether or not side airbags system will also deploy the seat belt window bag pushes the edge of the should have deployed.
  • Page 147 The airbag material may sometimes After any accident, the car should be Electric parking brake cause abrasions and/or skin reddening taken to a Jeep Dealership immediately. Automatic transmission lever to the occupants as the airbags deploy Horn Enhanced accident response system and unfold.
  • Page 148 blinking and will continue to blink. In Driver's action Effect of the action Driver's action Effect of the action order to move your car to the side of the road, you must follow the system reset The right direction 12. Take the 6.
  • Page 149 Child restraints - Carrying How various systems in your car were WARNING children safely operating. Whether or not the driver All occupants of a car, including infants 133) SEVERE DANGER When a front and passenger safety belts were and children, must travel seated and passenger airbag is fitted, do not install buckled/fastened.
  • Page 150 Jeep Dealership 143) Remember that, in the event of an slack so that it is comfortable and not immediately and have it fixed.
  • Page 151 160) The pretensioner may be used only pretensioners may not be deployed in an objects could cause harm if the vehicle is once. Contact a Jeep Dealership to have it impact or, in a lower number of cases, in a collision severe enough to cause the replaced after it has been deployed.
  • Page 152 Take should preferably travel in the rear seat of appropriate for the size of the child. your vehicle to a Jeep Dealership for the car with a suitable restraint system. 184) Side Air Bags need room to inflate.
  • Page 153 191) In a collision, an unrestrained child can become a projectile inside the vehicle. The force required to hold even an infant on your lap can become so great that you could not hold the child, no matter how strong you are. The child and others could be severely injured or killed.
  • Page 154   In Europe the characteristics of child restraint systems are ruled by the regulation ECE-R44, dividing them into five weight groups:   Group Weight ranges Size class / Fixing ISO/L1 Group 0 Indicatively up to 9 months up to 10 kg in weight ISO/L2 ISO/R1 ISO/R1...
  • Page 155 WARNING 192) Extreme Hazard! Never place a rearward facing child restraint in front of an active air bag. Refer to the warnings on the sun visor labels. Deployment of the air bag in an accident could cause fatal injuries to the baby regardless of the severity of the collision. It is advisable to always carry children in a child restraint system on the rear seat, which is the most protected position in the event of a collision.
  • Page 156 Child restraint system the event of sudden decelerations or a Group 2 installation with universal seat collision. belts The rearward facing child restraint system is restrained by the seat belts of The figures in the following sections the car, as shown in fig. 138. The child are examples of different types of child restraint system restrains the child with restraint systems.
  • Page 157 Children who weigh between 22 kg and 198) When your child restraint system is 36 kg and who are tall enough to use not in use, secure it in the vehicle with the adult belt strap may use a Group the seat belt or ISOFIX anchorages, or remove it from the vehicle.
  • Page 158 FRONT PASSENGER AIRBAG AND CHILD RESTRAINT SYSTEMS: ATTENTION F1B0129C...
  • Page 159 Seat belts for children over 12 ISOFIX restraint system if you run your finger along the gap years of age between the backrest and seat cushion. Children over 1.50 m in height can wear seat belts instead of using child restraint systems.
  • Page 160 4. If the child restraint system has a route the tether strap under the head restraint and between the two posts. If tether strap, connect it to the respective upper anchoring. See the “Installing not possible, lower the head restraint and pass the tether strap around the child restraint systems using the top anchoring”...
  • Page 161 The child must be transported child restraint system is correctly fixed to WARNING rearward facing until 15 months. the brackets when you hear the click. The protection of the child restraint 210) An incorrectly anchored tether strap 203) Never allow a child to put the belt system is greater in the event of a side could lead to increased head motion and strap under an arm or behind their back.
  • Page 162 Child restraint system installation The table below shows the various installation possibilities for ISOFIX child restraint systems on seats fitted with ISOFIX anchorages in accordance with European standard ECE 16.   The following table provides guidelines on positioning child restraint systems on the car seats. Each child restraint system position complies with the UNECE standards.
  • Page 163 Number of seats Seat number 5 (*) Airbag Airbag ENABLED DISABLED Seat suitable for ISOFIX forward facing child YES (IUF) YES (IUF) restraint system (F2 | F2X | Seat suitable for auxiliary YES (only B2) YES (only B2) child restraint systems (B2 (IUF) (IUF) / B3)
  • Page 164 ® using the seat belt with three anchor points or the ISOFIX anchorages. IMPORTANT Jeep recommends fitting the child restraint system according to the instructions, which must be included.   Weight group...
  • Page 165 Peg Perego Viaggio 2-3 Shuttle Plus the three-point seat belt and the ISOFIX Group 2: from 15 kg to 25 (for versions/markets, where anchorages of the vehicle, if present. Jeep recommends installing it using the ISOFIX provided) from 95 cm to 135 cm Jeep order code: 50290504 anchor points of the vehicle.
  • Page 166 Peg Perego Viaggio 2-3 Shuttle Plus Group 3: from 22 kg to 36 the three-point seat belt and the ISOFIX (for versions/markets, where anchorages of the vehicle, if present. Jeep provided) from 136 cm to 150 cm recommends installing it using the ISOFIX Jeep order code: 50290504 anchor points of the vehicle.

  • Page 167: Safety Tips

    If the warning light blinks or parts. Open welding or loose connections cracks and bulges. Check the wheel nuts stays on while driving, go to a Jeep may permit exhaust gas to enter the for tightness. Check the tyres (including Dealership immediately for the necessary passenger compartment.
  • Page 168 the spare) for proper cold inflation 216) Always make sure that all those on 221) ONLY install floor mats designed pressure. board the car are seated and are wearing to fit your vehicle. NEVER install a floor their seat belts correctly. mat that cannot be properly attached Lights and warning lights 217) Exhaust gases can injure or kill.
  • Page 169 227) It is recommended to only use mild soap and water to clean your floor mats. After cleaning, always check your floor mat has been properly installed and is secured to your vehicle using the floor mat fasteners by lightly pulling mat.
  • Page 170 Blank page...
  • Page 171 ACTIVE DRIVE (4WD) AND (AC) ......250 JEEP ACTIVE DRIVE LOW (4WD CHARGING CABLE LOW) .
  • Page 172 TOWING FOR TOURISM (TOWING OF CARAVANS, ETC.) ......268 DRIVING TIPS ....269 TRANSPORTING THE CAR .

  • Page 173: Starting The Engine

    "ELECTRIC" operating mode. starting procedure. position N (Neutral) or P (Park). Apply Under the following conditions, however, If the problem persists, contact a Jeep the handbrake before selecting a gear. the heat engine may be used: Dealership. when the temperature of the hybrid...
  • Page 174 (available from your Jeep Dealership) is procedure, and has not experienced an always available; recommended. extended park condition as identified in while holding down the brake pedal, "Extended Park Starting" procedure, it...
  • Page 175 PRECAUTIONS When the car stops, turn the ignition should be warned not to touch the parking device from ENGINE position to the Before switching the engine off, keep brake, brake pedal or the shift level. STOP position, the accessories will it idling for a few minutes so that 233) Do not leave the key in or near the remain powered for three minutes.

  • Page 176: When Parked

    WARNING NEVER leave the car with For more information, please refer to start during this time, wait at least two the gearbox in neutral (or, on versions "Jump starting procedures" in "In case of minutes for the starter motor to cool emergency".
  • Page 177 a gear (1st gear with the car parked parking brake before turning the gear A slight movement of the brake pedal facing uphill or reverse gear with the car selector to P (park). Otherwise it may be may be detected when engaging the parked facing downhill).
  • Page 178 Jeep warning will sound. The rear stop lamps The driver side door is opened. Dealership. will also be illuminated automatically The car is not in the P (Park) position. while the car remains in motion.

  • Page 179: Hold 'N' Go" Function

    Have the vehicle. Allowing children to be in a brake system repaired immediately by the vehicle unattended is dangerous for Jeep Service Network. a number of reasons. A child or others could be seriously or fatally injured. "HOLD 'N' GO" FUNCTION...

  • Page 180: Manual Transmission

    MANUAL TRANSMISSION clutch pedal, however lightly. In some lower gear and releasing the clutch may circumstances, the electronic clutch result in engine damage. (where provided) control could cut in by interpreting the 52) When descending a hill, be very incorrect driving style as a fault. careful to downshift one gear at a time to 253) prevent overspeeding the engine which...
  • Page 181 WARNINGS Engage N (or P) in case of prolonged stops. Never try to select position P when the car is moving. To shift from position N to D or R, you Before leaving the car, apply the need to press the brake pedal. It is electric parking brake and set the gear advisable not to accelerate and to make lever to this position.
  • Page 182 running or off) and the brake pedal must lever towards "−": shift down. WARNING With engine running and car be pressed. Moreover, it is necessary to stationary, in "Sequential mode", the The engagement of a lower or higher gear press the button on the gear lever. request for engaging 2nd gear is not is only permitted if the engine revs allow accepted by the system (whether the...
  • Page 183 10 seconds. be put in neutral (N), do not tow the car In both cases, if the described and contact a Jeep Dealership. Should conditions and times are not respected, the lever be in P, release it before towing...

  • Page 184: Automatic Transmission

    the transmission in neutral (N) or P D = Drive, (automatic forward speed) IMPORTANT (Parking). "AutoStick": To protect the clutch, never use + shifting to a higher gear in 53) There must be no objects (such as the accelerator to keep the car manual (sequential) driving mode;...
  • Page 185 stopped or is moving at a low speed, parking brake, otherwise moving the gear for driving needs and maximum fuel in addition to pressing the button (1) lever from P ("Park") might be difficult. economy in terms of consumption. fig. 153 the brake pedal must also be To check the actual engagement of the In this position, the transmission shifts pressed (see "Gear engagement disabling...
  • Page 186 WARNING In the event of a temporary pedal must be depressed. FUNCTION failure it is anyway recommended to Transmission function is monitored contact a Jeep Dealership as soon as GENERAL WARNINGS electronically for abnormal conditions. possible. Failure to comply with what is reported...
  • Page 187 do not shift gears between positions other controls or inadvertently start the and that the electric parking brake is P ("Park"), R (Reverse), N (Neutral) or D engine; engaged. (Drive) with engine running at a speed bringing the transmission to a position 258) Do not shift the gear lever to N above idling;...

  • Page 188: Stop/Start System

    Hold" system available and restart the and repeat the procedure. If the problem driver wants to move off. engine, using the gear lever as described persists, contact a Jeep Dealership. In this way, the car efficiency is previously. Models with automatic...

  • Page 189: Speed Limiter

    To activate the system, press the (ACC)" functions (where provided) will button on the steering wheel fig. 155. 59) Always contact a Jeep Dealership to not be available while the Speed Limiter replace the conventional battery. Replace function is in use.

  • Page 190: Electronic Cruise

    SETTING THE DESIRED SPEED The device is disabled until the speed automatic transmission when the Cruise drops below the set limit, after which it Control function is activated. Failure to Proceed as follows: reactivates automatically. respect this precaution with damage the operate the device (see the previous system.

  • Page 191: Adaptive Cruise Control (Acc)

    "N" for versions with automatic transmission. comfort provided by the electronic Cruise 264) 262) In case of a malfunction or failure of Control when on the motorway or out of the device, contact a Jeep Dealership. town with light traffic.
  • Page 192 The use of the device is therefore not NOTES: Adaptive Cruise Control buttons advantageous on busy roads or in town. If the sensor does not detect any The ACC system allows the electronic vehicle ahead, the device will maintain a fixed set speed.
  • Page 193 WARNING It is dangerous to leave the If the ACC system is set when the car The car parking brake is applied. device activated when it is not used. speed is below 30 km/h, the Set Speed Driver seatbelt is unbuckled at low There is a risk of inadvertently activating shall be defaulted to 30 km/h.
  • Page 194 SETTING THE DISTANCE Before returning to the previously set NOTES: BETWEEN CARS speed, bring the speed close to that When you override and push the SET + value, then press the RES button and button or SET - button, the new Set The distance between your car and the release it.
  • Page 195 Distance setting, for example 4 bars the distance setting is changed; NOTE The device detects the direction (maximum) - Display 10" the Adaptive Cruise Control device is of traffic automatically when the car deactivated/cancelled. passes from left-hand traffic to right- hand traffic.
  • Page 196 The ACC page may be displayed again in snow, rain, mud or other obstruction, (fixed speed) is still available. Refer to the case of any ACC activity, including: have the radar sensor realigned at a Jeep “Electronic cruise control mode” in this Dealership. deactivation of the system;...
  • Page 197 164, the device may not obstruction, have the windscreen and detect the presence of a vehicle on the front camera inspected at a Jeep the lane. Device performance could be Dealership. limited according to speed, load, traffic ACC/FCW request for action indication conditions and gradient steepness.
  • Page 198 Small cars Some narrow vehicles (e.g. bicycles and motorcycles fig. 166) travelling near the outer edges of the lane or which enter the lane from kerbside are not detected until they are fully in the lane. Sufficient distance from the cars ahead may not be guaranteed in these cases.
  • Page 199 value, then press the RES button and 272) The Adaptive Cruise Control (ACC) is steep slopes. When circumstances do not release it. a system designed for driving comfort. allow safe driving at a constant speed. It is not a substitute for active driving 275) Leaving the Adaptive Cruise Control involvement.

  • Page 200: Four-Wheel Drive - Jeep Active Drive (4Wd) And Jeep Active Drive Low (4Wd Low)

    Disabling the 4WD LOW mode during parking manoeuvres). In these To disable the 4WD LOW mode, the cases, go to a Jeep Dealership to have the car must be stopped and the automatic radar sensor realigned or replaced. transmission lever must be in neutral (N).

  • Page 201: Selec-Terrain

    SELEC-TERRAIN™ and off-road in the case of grounds with WARNING If you try to select an poor grip, such as roads covered by operating mode and the operating mode (where provided) snow. selection system does not allow it, a Selectable in hybrid system operating dedicated message will appear on the 278) modes: "HYBRID".

  • Page 202: Sport Mode

    IDLE COASTING Engaging the SPORT mode (see the physical contact with the flooded vehicle. "SPORT mode" chapter in this section). Immediately contact the rescuers, police (where provided) Special driving situations (e.g. or fire brigade and inform them that this The "Idle coasting" is a function that is a vehicle with a high voltage system.

  • Page 203: Parksense System - Versions With 4 Sensors

    PARKSENSE SYSTEM - The sensors can detect obstacles from If an obstacle is detected in the left a distance of about 30 cm up to 200 and/or right rear part, the display Versions with 4 sensors cm from the rear bumper horizontally, will show a single flashing arc in the (where provided) depending on the position, orientation...
  • Page 204 Sound at long intervals/fixed arc Continuous sound/flashing arc Uconnect™ volume down: yes Rear distance: 150-120 cm Left arch: off Middle arch: 5th arc on fixed Right arch: off Acoustic warning: The acoustic warning increases as objects become closer to the car Uconnect™...
  • Page 205 Then perform an ignition If the Uconnect™ system is on when cycle. Contact a Jeep Dealership if the the ParkSense system sends an acoustic message appears again. warning, the volume will be reduced.

  • Page 206: Parksense System - Versions With 12 Sensors

    NOTE If any objects are attached to the sensors could detect the ball mount and area of the sensors carried out by a Jeep bumper within a 2 m field of view, they hitch ball assembly, depending on its size Dealership.
  • Page 207 The system will remain active until the “Settings” in the “Multimedia” section Single sound 1/2 second/fixed arc car speed is increased to approximately for further information. 11 km/h or above. In position R The ParkSense warning screen is located (Reverse) and above the operating speed on the instrument panel display.
  • Page 208 Sound at close intervals/ flashing arc Continuous sound/flashing arc Uconnect™ volume down: yes Rear distance: 150-120 cm Left arch: off Middle arch: 5th arc on fixed Right arch: off Acoustic warning: The acoustic warning increases as objects become closer to the car Uconnect™...
  • Page 209 Rear distance: greater than 30 cm No sound/fixed arc Continuous sound/flashing arc Left arc: 1st arc flashing Middle arch: 1st arc flashing Right arc: 1st arc flashing Acoustic warning: continual Uconnect™ volume down: yes Driving in forward direction The ParkSense warning screen will be displayed when an obstacle is detected while the car is in any gear, as long as the car speed is below 11 km/h.
  • Page 210 Rear distance: 100-65 cm the section related to functions that display the dedicated message for Left arch: off can be programmed by the user of approximately five seconds. For more the Uconnect™ system. Refer to the information, refer to the “Display” Middle arch: 3rd arc on fixed Right arch: off "Settings"...
  • Page 211 Then perform an ignition of side obstacles near the car using the debris, to avoid system malfunctions. cycle. Contact a Jeep Dealership if the parking sensors located in the front and The ParkSense system might not detect message appears again.
  • Page 212 Arcs - Right Flashing Flashing them. The sensors must not be covered in the electrical system. Contact a Jeep with ice, snow, slush, mud, dirt or Dealership as soon as possible for repair The acoustic debris, to avoid system malfunctions.

  • Page 213: Active Parksense System (Automatic Park Assist)

    Jeep During a semi-automatic manoeuvre, sounds the continuous tone. Also, the Dealership.
  • Page 214 be required to manually complete the transmission. If the manoeuvre cannot parking manoeuvre. be completed within the maximum The system may not work in all amount of shifts, the system will cancel conditions (e.g. environmental conditions and the instrument panel display will such as heavy rain, snow, etc., or if instruct the driver to complete the searching for a parking space that has...
  • Page 215 LED will turn OFF if any of the above protruding into the parking space (e.g., Area detected - Continue moving forward conditions are not present. ladders, liftgates, etc. from surrounding objects/vehicles). SYSTEM OPERATION When seeking for a parking space, 78) 77) the driver should drive as parallel or When Active ParkSense (Automatic Park perpendicular (depending on the type of...
  • Page 216 Area detected - Engage reverse gear versions). If the manoeuvre cannot driver should check their surroundings be completed within six shifts, the and be prepared to stop the car either When the gear selector is put in the system will cancel and the instrument when instructed to, or when driver R (Reverse) position, the system may panel display will instruct the driver to...
  • Page 217 Check the surroundings - Move forward Once the car is in a standstill condition, manual transmission gear lever in first the driver will be instructed to put the gear. gear selector in R (Reverse) position. Perpendicular Active ParkSense Check the surroundings - Engage reverse (Automatic Park Assist) gear Operation and related display...
  • Page 218 the car if the direction indicator is not Area detected - Continue moving forward Area detected - Engage reverse gear activated. When the driver places the gear lever The driver needs to make sure that into the reverse position, the system may the selected parking space for the instruct the driver to wait for steering to manoeuvre remains free and clear of any...
  • Page 219 transmission) and R (Reverse). If the NOTE It is the drivers responsibility to Check the surroundings - Move forward manoeuvre cannot be completed within use the brake and stop the car. The six shifts, the system will cancel and the driver should check their surroundings instrument panel display will instruct and be prepared to stop the car either...
  • Page 220 Once the car is in a standstill condition, Check the surroundings - Move in reverse Exit” function. After the selection, the the driver will be instructed to place the system activates and warns the driver gear lever into the reverse position. on the dashboard display about the operations that have to be carried out to Check the surroundings - Engage reverse...
  • Page 221 Check the surroundings - Stop the car and Check the surroundings - Stop the car Check the surroundings - Move forward remove your hands from the steering wheel / Check the surrounding area - Wait until the manoeuvre is completed 5520802D 5520815D Check the surroundings - Engage D position...
  • Page 222 Check the surroundings - Engage reverse Important information path are actually compatible with the gear / Check the surroundings - Wait for parking place identified by the system. If the sensors undergo collision completion of the manoeuvre The use of wheels and tyres that are which alters their position, the system different size to the original equipment operation could be greatly affected.

  • Page 223: 360° Surround System

    10 seconds or until the driver must never allow their attention area of the sensors carried out by a Jeep gear lever is moved to P (Park) or the to lapse during potentially dangerous Dealership.
  • Page 224 will light up. The button will light up and to reverse will show the screen magnified fig. 218 on the Uconnect™ system the selected view type will appear on again. screen: each image. Shifting from reverse to neutral will keep (1) Rear view and top view In the top view, the car will be shown the image on screen for a few seconds...

  • Page 225: Lanesense System

    warning on the instrument panel display help for the driver, but the driver must vehicle shampoo if necessary. In washing to prompt the driver to remain within the never allow their attention to lapse during stations which use steam or high-pressure lines.
  • Page 226 lane line appear grey. See fig. 221 (7" display) or fig. 222 (10" display). 5520653D 5520791D Press the fig. 220 button twice until the LED lights up to deactivate the 5520789D LaneSense system. A dedicated message will appears on the instrument panel display (where provided).
  • Page 227 5520793D 5520881D 5520880D Changing the system settings The LaneSense system has settings to adjust the intensity of the steering wheel torque (Low / Medium / High) and the warning zone sensitivity (Early / Medium / Late) that you can configure using the Uconnect™...

  • Page 228: Traffic Sign Recognition

    In the event of a failure fig. 230: instrument panel display. of the camera, contact a Jeep Dealership. speed limits; This area shows only the speed limit 88) Do not cover the operating range of no overtaking;...

  • Page 229: Isa (Intelligent Speed Assist)

    ISA (Intelligent Speed the area of the instrument panel display IMPORTANT only when the following filters occur: Assist) system the additional fog signal will appear if 91) Functionality may be limited or the (where provided) the front or rear fog lights are on; system may not work if the sensor is The ISA system prompts the driver to the additional snow signal will appear...

  • Page 230: Highway Assist System

    The system activation is signalled by the You can also disable the Speed Limiter a grey indication will appear on the green symbol and a message on the by pressing the CANC button. In this instrument panel display and the system instrument panel display.
  • Page 231 if the speed of the Adaptive Cruise your hands off the steering wheel for 35 the instrument panel display (see the Control (ACC) device can be set to a seconds. description in the following pages). higher value (top speed 150 km/h), the SYSTEM STATUS WARNING When the Highway Assist Highway Assist system is only available...
  • Page 232 Active system (hands removed from the narrow, winding and curvy streets; WARNING steering wheel for a long time) poor visibility (due to heavy rain, snow, fog, etc.); If you do not placed your hands on 294) Many unpredictable situations may front lights of incoming cars or direct the steering wheel, a third screen will arise that can affect the performance of...

  • Page 233: Rear Camera (Parkview Rear Backup Camera)

    299) If the windscreen glass must be position. replaced due to scratches, chipping or (PARKVIEW REAR breakage, contact exclusively a Jeep BACKUP CAMERA) If activated, the grid is positioned on Dealership. Do not replace the windscreen the image to highlight the width of the...

  • Page 234: Charging

    CHARGING Charging port LED WARNING Next to the charging port there are (Plug-In Hybrid versions) some LEDs (1) fig. 234 that indicate 302) The driver is always responsible 303) 304) the charging status by means of four for parking and other potentially different colours and related flashing dangerous maneuvers.
  • Page 235   and the table "Mode 2" Cable Variants in the "Power sources that can be indicates that a indicates to refer to the used" chapter) or a replacement cable charging timer has descriptions and figures in recommended by FCA. been set. the Owner Handbook.

  • Page 236: Power Sources That Can Be Used

    Power sources for electric Before charging, check the symbol ALWAYS unplug the device from the charging. Identification (where provided) on the charging cable domestic power supply socket and car and compare it with the symbol on the of vehicle compatibility. ports.
  • Page 237 Before charging in your own home, or elsewhere, check the allowable current intensity by contacting a specialised technician: it is advisable to contact the Jeep Dealership. 5520748D TYPES OF CHARGING CABLES Two different types of cables can be used for charging: "Mode 2"...
  • Page 238 307) Do not connect the charging cable overvoltage protection or similar units connector if there is dust and/or water on cannot be used together with the charging the charging port. Making the connection cable as they may present a risk of fire, in the presence of water or dust on the electrocution, etc.
  • Page 239 330) The device is to be used exclusively for charging the car. 331) Never attempt to make a repair and/or perform maintenance on the charge cables, this may result in serious personal injury or even death. Always contact a Jeep Dealership.
  • Page 240 "Mode 2" cable variants table The following table shows the list of the specific cable types and the amperages allowed for each country where the car is sold. This amperage is the limit allowed when the charging power is set to the highest level.  ...
  • Page 241 Country group for "Mode 2" cable The list of countries contained in each "Country Group" associated with the "Mode 2" cable is shown below. Refer to the images under the list for more details. Group 1: Albania, Austria, Belgium, Bulgaria, Croatia, Czech Republic, Estonia, Germany, Greece, Hungary, Iceland, Latvia, Lithuania, Luxembourg, Macedonia, Morocco, Netherlands,...
  • Page 242 WARNING Never carry out any repair the specific "Mode 2" work on your own: always contact the charge cable cannot be Jeep Dealership. 5520750D used for domestic power For the type of failure, refer to the distribution networks where description under "Charging system...
  • Page 243 332) The device is to be used exclusively for charging the car. 333) Never attempt to make a repair and/or perform maintenance on the charge cables, this may result in serious personal injury or even death. Always contact a Jeep Dealership.
  • Page 244 CHARGING SYSTEM FAILURE Any faults during charging are displayed by the LEDs, either steady or flashing, located on the front of the charging status control unit. Refer to the table below.   GREEN LED RED LED YELLOW LED Description Action/Consequence Charging cable not connected to the domestic charging socket or power failure in the domestic...
  • Page 245 GREEN LED RED LED YELLOW LED Description Action/Consequence Overheating during charging at a lower current level (see point 4) Proceed as follows: disconnect the charge cable from the car and from the domestic power socket with care (the domestic power plug may be hot); Overheating at the charging socket please wait for the domestic ON (Flashing)
  • Page 246 Dispersion of electricity on the car charge again. In case of a new fault, contact a Jeep Dealership The system will make a new charge ON (flashing) Electric charging current too high attempt after 30 seconds (6 attempts in total).
  • Page 247 ON (5 blinks) then try charging again. In case of a new fault, contact a ON (6 blinks) Jeep Dealership ON = LED on OFF = LED off BLINK = 0.5 seconds ON / 0.5 seconds OFF / 3 seconds pause...
  • Page 248 If you need to clean the device, use a made incorrectly and NOT carried out by soft cloth slightly dampened with a mild the Jeep Dealership will invalidate the detergent solution, then wipe dry with a Warranty and the above requirements.

  • Page 249: Procedure For Charging From Adomestic Power Socket (Ac)

    charging station and the charging port unroll the charging cable and connect located on the car. it to an AC charging port, fig. 250; PROCEDURE FOR CHARGING FROM A DOMESTIC POWER SOCKET (AC) (Plug-in Hybrid version) 5520614D 334) 335) 336) 337) 338) 339) 340) 341) 342) 343) remove the protective cover (2) 98) 99) 100) 101) 102) 103) 104) 105) fig.
  • Page 250 the state of charge set in the Uconnect™ the button (2) fig. 254 on the charging system menu. port or use the dedicated App installed on your smartphone. WARNING Use only the charging cable check by turning on the LEDs on supplied with the car or a replacement the cable control unit that there are no cable recommended by FCA.
  • Page 251 To complete the charging, proceed as close the charging flap, making sure it domestic power supply socket and car follows: locks properly; ports. roll up the charging cable correctly, 336) Incorrect setting of the charge unlock the doors of the car allowing repositioning the protective cover current intensity can overload or overheat the charging cable to unlock;...

  • Page 252: Charging Procedure From Wallbox Charging Station ("Smart" Wallbox)

    "smart" wallbox depending on the building's electrical components may be voltage activated. charging stations, contact a Jeep system. Therefore, it is normal to hear noises Dealership. For the charging procedure, refer to the during this operation.
  • Page 253 park the car safely (automatic transmission lever in position "P" - Park); engage the electric parking brake; switch off the engine; remove the charging cable (optional) fig. 257 from the boot (inside a special bag), remove the protective cover (where provided) on the two-colour connector connector (4) and plug it into the socket of the public charging station, fig.
  • Page 254 DISCONNECTING THE "MODE 3" NOTE In some countries the "Mode 3" charging station (Mode 3). It is therefore CHARGING CABLE cable is not available. always advisable to check that the level is set as desired for the actual charging type To complete the charging, proceed as WARNING Always connect the connector that is about to be carried out.

  • Page 255: Charging Cable Emergency Unlock

    NOTE Excessive force may break the 5520747D cable retainer. NOTE To restore correct operation of the system, contact the Jeep Dealership.
  • Page 256 INTERRUPTING THE CHARGING that the charging cable is still connected NOTE The (1) fig. 265 is only active PROCEDURE inside the charging port, charging will when the doors are unlocked. restart automatically and the cable will By inserting the charging connector of END OF CHARGING PROCEDURE be locked inside the charging port.

  • Page 257: Ecoasting" Mode (Energy Saving)

    "eBraking" MODE Pressing button activates the "Plus" mode, which differs from the "Normal" (HIGH-VOLTAGE BATTERY mode for an increased deceleration when CHARGING) the accelerator pedal is released. (Plug-in Hybrid version) The "eBraking" mode, which is always active regardless of the selected operating mode (heat engine or electric motor operation), activates the high- voltage battery charging when the brake...

  • Page 258: Refuelling The Car

    REFUELLING THE CAR REFUELLING PROCEDURE (DIESEL AND PETROL Before refuelling, check you are using VERSIONS) the correct type of fuel. Opening the flap Furthermore, turn off the engine before To refuel proceed as follows: refuelling. Open the flap fig. 269, from the point PETROL AND HYBRID ENGINES shown by the arrow Only use unleaded petrol with an octane...
  • Page 259 switch off the engine and set the when the depressurisation operations NOTE After pressing the button automatic transmission lever to "Park" are completed, it will be possible fig. 272/fig. 273, you have 20 minutes ("P"); to refuel (during this procedure a to refuel.
  • Page 260 the boot, on the side panel near the fuel flap. 1. Open the liftgate. 2. Remove package tray if equipped. 3. Remove the access flap (1) fig. 275 located on right interior trim panel to release the cable with the tip of your key. 5520875D 5520655D 3.
  • Page 261 Diesel fuel tank, this can result in serious with the refilling, to prevent spillage of instrument panel to switch off before engine damage, contact a Jeep Dealership. AdBlue ® moving the car. The indication may stay Do not add additives or other fluids extract the nozzle.
  • Page 262 The consumption of AdBlue emissions 5.0% (V/V) ethanol compliant with ® 351) A fire may result if fuel is pumped additive depends on the conditions of use EN228. into a portable container that is inside of the car and is indicated by means of the of a vehicle, resulting in a risk of burns.

  • Page 263: Towing Trailers

    TOWING TRAILERS a cable with a cross-section of not IMPORTANT less than 2.5 mm². In addition to the WARNINGS electrical branches, the car electrical 109) Follow these guidelines to maintain system can only be connected to the 354) 355) 356) 357) 358) your vehicle’s performance: The use of supply cable for an electric brake and For towing caravans or trailers the car...
  • Page 264 5520338D since there is risk of causing accidents. For fixed ball tow bar attach the Contact a Jeep Dealership. clip directly to the designated point. 5520350D The ball head tow bar can be...
  • Page 265 356) Weight distributing systems may not be compatible with surge brake couplers. Consult with your hitch and trailer manufacturer or Jeep Dealership for more information. 357) The ABS with which the car is equipped will not control the braking system of the trailer.
  • Page 266 REMOVABLE BALL HEAD TOW BAR J0A0423...
  • Page 267 Should the removable ball head bar loading position even when the knob is Installing the ball head tow bar require repair, only consult with a Jeep released. Remove the cap from the mounting pipe. Dealership.
  • Page 268 Trailer towing requirements – Trailer water area. brakes WARNING To install a tow hook contact Do not interconnect the hydraulic a Jeep Dealership. WARNING braking system or vacuum system of your Trailer towing requirements car with that of the trailer. This could...
  • Page 269 automatic transmission to P (Park) on the towing car. Secure or attach chocks to the trailer wheels. 360) Do not connect the trailer brakes to the hydraulic lines of the car braking system, overloading on the trailer may cause failure. You might not have brakes when you need them and could have an accident.
  • Page 270 TOWING FOR TOURISM (TOWING OF CARAVANS, ETC.) Towing the car by another vehicle   TOWING CONDITION WHEELS LIFTED FROM GROUND FRONT WHEEL DRIVE (FWD) FOUR-WHEEL DRIVE Towing on level ground NONE NOT PERMITTED NOT PERMITTED REAR NOT PERMITTED NOT PERMITTED Towing on trolley FRONT PERMITTED...
  • Page 271 DRIVING TIPS NOTES: 5. Set the ignition device to the ENGINE position and start the engine. Respect the local and national laws 114) in force for towing the car. Contact your 6. Press the brake pedal and hold it national and local authorities for more pressed.
  • Page 272 Plug-In Hybrid versions, refer to the boot. The weight of the car and high revs when the car is stationary; its arrangement greatly affect fuel relevant section on the official Jeep this causes the engine to warm up consumption and stability. website.
  • Page 273 In order to maximize the energy Switching off superfluous functions Electrical operating mode efficiency of the car, it is suggested to If not strictly necessary, remember to The range of the car in electric mode is use the passenger compartment air switch off functions such as seat heating influenced by several factors (including conditioning function only when strictly...
  • Page 274 WARNING When crossing a ford, do not be at greater risk of serious or even fatal For these operations, contact a Jeep exceed a speed of 8 km/h. injury. Dealership.
  • Page 275 Driving uphill off-road If the wheels start to slip as you suspension. Contact a Jeep Dealership if approach the crest of a hill, ease off the they are. NOTE Before attempting to climb a hill, accelerator and maintain headway by...
  • Page 276 IMPORTANT 114) Frequent restarts, sudden accelerations and braking, long distances travelled at high speed, heavy loads, high power consumption in the passenger compartment, low outside temperature and uphill gradients can reduce the driving range. 115) When driving through water, do not exceed 8 km/h.
  • Page 277 IN CASE OF EMERGENCY Have a flat tyre or a burnt-out bulb? HAZARD WARNING LIGHTS ..276 At times, a problem such as these may HELP CALL ....276 interfere with your driving experience.

  • Page 278: Hazard Warning Lights

    HAZARD WARNING Emergency braking In the event of emergency braking LIGHTS the hazard warning lights switch on Press button fig. 282 to switch the lights automatically as well as the warning on/off. When the hazard warning lights lights in the instrument are on, the warning lights panel.
  • Page 279 Uconnect™ system display. the Uconnect™ system display when the Privacy: GPS location is always active for malfunction is detected. Contact a Jeep Once the connection has been HELP. Deactivating it via the "Settings" Dealership as soon as possible.

  • Page 280: Assist Call

    Read more problems related to the car power source about the general conditions of service (e.g. low conventional battery). and data protection policies on the Jeep When using the services, customers official website. 5520847D shall keep their passwords secret for...
  • Page 281 When Uconnect™ system display. the Uconnect™ system display. Contact a geolocation is off, the vehicle position is Jeep Dealership as soon as possible. Once the connection has been only tracked by the navigation, safety, established, the following data will be...

  • Page 282: Uconnect Box System

    NOTE Regardless of charge, the battery into contact with uncovered high-voltage tunnels, garages, multi-storey car parks, must be replaced every 5 years by a Jeep cables. NEVER touch exposed electric mountains. dealership. cables: danger of ELECTROCUTION;...

  • Page 283: Replacing A Bulb

    REPLACING A BULB if you notice any electrolyte leakage WARNING from the high-voltage battery, do not go near the car. If the electrolyte from the 365) 366) 367) 368) 369) 370) 365) Before replacing the bulb, wait for high-voltage battery comes into contact GENERAL INSTRUCTIONS the exhaust ducts to cool down: DANGER with the eyes or skin, blindness or skin...
  • Page 284 and driving” section). Also make sure that the engine is cold, to avoid burns.
  • Page 285   Exterior bulbs Lights type power LED (Contact a Jeep Dealership for – High beam / dipped beam headlights replacement) LED (Contact a Jeep Dealership for – Front side lights/daytime running lights (DRL) replacement) Front direction indicators WY21W LED (Contact a Jeep Dealership for –...
  • Page 286 Interior bulbs Lights Bulb ref. Front courtesy light Front courtesy light (sun visor) Rear ceiling light (models without sunroof) Rear ceiling light (models with sunroof) Interior lights HT-168 Ceiling light (storage compartment) HT-168...
  • Page 287 4. Extract the bulb and replace it. 9. Tighten the fixing screw and replace 5. Refit the connector and turn the bulb the protection caps. NOTE It is advisable to contact a Jeep holder clockwise. Dealership. Rear fog light 6. Reinstall the wheel arch liner.
  • Page 288 5. Refit the lamp by snapping in the locking tab features on the left and right edges of the fog lamp. NOTE It is advisable to contact a Jeep Dealership. Reversing lights 1. Open the liftgate.

  • Page 289: Fuses

    (where provided) 372) 373) 374) 375) 376) 116) NOTE The mirror courtesy lights are WARNING For fuse replacement, contact LED-type. Contact a Jeep Dealership for replacement. a Jeep Dealership. GENERAL INFORMATION Rear ceiling light fig. 295 change the bulb (1) releasing it from the  ...
  • Page 290 For fuse replacement, contact a Jeep Dealership. 5520682D 5520684D 5520465D DASHBOARD FUSEBOX The fuse box fig. 302 is located near the left side of the steering column and the...
  • Page 291 ENGINE COMPARTMENT FUSEBOX   Position Maxi fuse Cartridge fuse Micro fuse Description – – 30 A green Heated rear window – – 40 A green Climate control system fan – – 7.5 A brown (petrol and Climate control compressor Diesel versions) 5 A amber (Plug-in Hybrid version) –...
  • Page 292 (air bag system, braking system), power unit systems (engine system, gearbox system) or steering system blows, contact an authorized dealer. 376) For fuse replacement, contact a Jeep Dealership. IMPORTANT 116) If it is necessary to wash the engine compartment, take care not to directly hit the fuse box, and the windshield wiper motors with water.
  • Page 293 DASHBOARD FUSEBOX The interior fuse panel is in the passenger compartment on the left side, under the dashboard.   Position Foil fuse Description 20 A yellow Passenger side electric window motor 20 A yellow Driver side electric window motor Uconnect box, UCI/USB port, climate control system and radio controls, centre ceiling 20 A yellow light, electronic steering column lock, security gateway, EOBD port, climate control system power, radio power, folding door mirrors...
  • Page 294 Fuse/relay distribution unit in rear loading components To access the fuses, remove the access flat from the left rear panel of the luggage compartment. The fusebox fig. 303 is located closest to the rear of the car. 5520686D...
  • Page 295     Position Mini fuse Description 30 A green 230V power socket 30 A green Seat with stored positions 20 A yellow Sunroof - if provided 30 A green Electrically adjustable seat (passenger side) 30 A green Electrically adjustable seat (driver side) 7.5 A brown Electric lumbar adjustment (electrically adjustable seats) 15 A blue...

  • Page 296: Changing A Wheel

    CHANGING A WHEEL petrol versions), or in the box indicate the spare wheel (Plug-in Hybrid version) fig. 304. 377) 378) For Plug-In Hybrid versions: JACK 1. Open the liftgate and then remove the Please note that: load platform. the jack requires no adjustment; 2.
  • Page 297 CHANGING PROCEDURE Jack and tools fig. 306 Then position the wedge (1) fig. 308 (where provided) or a stone at the rear, 379) 380) 381) 382) 383) 384) on the wheel diagonally opposite the stop the car in a position that is not wheel to be replaced so as to prevent dangerous for oncoming traffic where unwanted movement of the car when it is...
  • Page 298 Tyres with unidirectional tread can doubts regarding the bolts tightening be recognised by arrows on the side of torque, contact a Jeep Dealership; the tyre which indicate the direction of rotation. It is compulsory to comply with this direction. Only in this way can the...
  • Page 299 Jeep Dealership where it can be If, after a puncture, it is necessary to clean so that the fastening bolts will not raised on a lift.
  • Page 300 Do not go under the car while it is spare wheel. The driving characteristics of raised with the jack. If it is necessary the car will be modified with the space- to work under the car, contact a Jeep...

  • Page 301: Tirekit

    TIREKIT puncture, change the tyre respecting the laws of the country you are travelling in; (where provided) insert the sealant cartridge (A) into the DESCRIPTION corresponding compressor compartment (B) and press it down hard. Remove the 389) 390) 391) 392) 393) 394) 395) 396) 397) 398) speed limit sticker (C) and apply it in a 118) clearly visible position;...
  • Page 302 If, however, the and suitable area and engage the electric pressure is lower than 1.8 bar / 26 psi, parking brake. Take the compressor and do not resume driving but contact a Jeep restore pressure using the black inflation Dealership. tube (L).
  • Page 303 - overheating hazard. regulations. the tire is too damaged. Contact a Jeep 390) Damage to the sides of the tire Dealership for any such operations. cannot be repaired. Do not attempt to use...

  • Page 304: Jump Starting

    Do not attempt jump starting if the the recharging system checked by a Jeep positive (+) to the positive terminal (+) of Dealership. conventional battery is frozen. The the car with flat conventional battery;...
  • Page 305 PLUG-IN HYBRID VERSION WARNING IMPORTANT CONVENTIONAL FLAT BATTERY If the conventional battery of the car is 399) Do not get too close to the radiator 119) Do not use the booster battery or flat, it can be jump started or a portable cooling fan: the electric fan may start;...

  • Page 306: Engine Overheating

    ENGINE OVERHEATING RELEASING THE selected, fig. 321 and press down on the release lever; AUTOMATIC 122) TRANSMISSION press the fig. 322 button with the 406) AND THE DUAL screwdriver provided; CLUTCH AUTOMATIC WARNING TRANSMISSION LEVER 406) You or others can be badly burned In the event of a failure, to move the by hot engine coolant (antifreeze) or gear lever from P (Park), proceed as...
  • Page 307 (3) fig. 324, make sure it locks correctly and fully tighten the fixing screws (2). IMPORTANT 123) It is advisable to contact a Jeep Dealership to have the refitting procedure carried out. If you would like to proceed 5520459D...

  • Page 308: How To Free Abogged-Down Car

    HOW TO FREE A BOGGED- stability program (ESC) to partially a speed higher than 24 km/h to prevent disengaged mode. For more information, DOWN CAR damage to the transmission. Revving refer to "Electronic Brake Control up the engine or spinning the wheels To free a car the wheels of which half may cause overheating and damage the System"...

  • Page 309: Towing A Broken-Down Car

    (*) WARNING If the transmission cannot be put in neutral (N), do not tow the car and contact a Jeep Dealership. If the automatic transmission lever is in "Park" (P), release it before starting to tow the car.

  • Page 310: Towing The Car

      TOWING THE CAR device in ENGINE mode, you must WARNING If a car is towed without manually disable the electric parking complying with the requirements shown For Plug-In Hybrid versions, it is brake whenever the driver's door is in the table, the transmission and/or recommended to tow the car with all the opened by pressing the brake pedal and the transfer unit might be seriously...
  • Page 311 Towing attachment warning label 129) Using the towing attachment The car is equipped with a tow eye fig. 326 which can be used to move it if it breaks down. If a towing attachment is used, make sure to follow the instructions in "Precautions for using the towing attachment"...
  • Page 312 409) Do not use a chain with a tow eye. 127) Ensure that the Electric Park Brake Chains may break, causing serious injury is released, and remains released, while or death. being towed. 410) Do not use a tow strap with a tow 128) Do not use a bumper mounted eye.

  • Page 313: Enhanced Accident Response System (Ears)

    ENHANCED ACCIDENT RESPONSE SYSTEM (EARS) The car is equipped with an Enhanced Accident Response System (EARS). Refer to "Occupant Protection System" under "Safety" for more information about the Enhanced Accident Response System (EARS) function. EVENT DATA RECORDER (EDR) (where provided) This car is equipped with an Event Data Recorder (EDR).
  • Page 314 Blank page...
  • Page 315 SERVICING AND MAINTENANCE Proper maintenance allows car SCHEDULED SERVICING ..314 performance to be maintained over ENGINE COMPARTMENT ..324 time, operating costs to be contained, CHARGING THE and safety system performance to be CONVENTIONAL BATTERY .

  • Page 316: Scheduled Servicing

    Vehicle Limited Warranty. It is advisable up). to inform a Jeep Dealership of any small DEMANDING USE OF THE CAR operating irregularities without waiting If the car is used in one of the following for the next scheduled service deadline.
  • Page 317 SCHEDULED SERVICING PLAN (gasoline versions) WARNING Once you have carried out the last intervention in the table, continue with the scheduled servicing, maintaining the frequency indicated in the plan by marking each operation with a dot or dedicated note. Warning: simply restarting the maintenance from the start of the plan may cause the allowed interval to be exceeded for some operations!  ...
  • Page 318 Thousands of miles Thousands of kilometres Years Check oil level of electro- hydraulic actuator and top up, if necessary (versions with dual-clutch automatic transmission) (6) Check the fuel/engine management systems operation, emissions and engine oil deterioration using the diagnosis equipment (where provided) (5) Change engine oil and filter Rotate tyres...
  • Page 319 (see the "Engine" chapter in the "Technical Specifications" section); strictly comply with the spark plugs replacement intervals in the Service Schedule. It is advisable to contact a Jeep Dealership for plug replacement.
  • Page 320 SCHEDULED SERVICING PLAN (Diesel versions) WARNING Once you have carried out the last intervention in the table, continue with the scheduled servicing, maintaining the frequency indicated in the plan by marking each operation with a dot or dedicated note. Warning: simply restarting the maintenance from the start of the plan may cause the allowed interval to be exceeded for some operations!  ...
  • Page 321 Thousands of miles Thousands of kilometres Years Visually inspect the condition of the toothed timing drive belt Change engine oil and filter Replace air cleaner cartridge Replace the passenger compartment filter Change the brake fluid every 24 months when using DOT 4 brake fluid (3) Replace fuel filter cartridge Replace accessory drive belt(s)
  • Page 322 Thousands of miles Thousands of kilometres Years Replace the Uconnect Box system battery (where provided) (1) The engine oil and filter change interval depends on the driving conditions and is signalled by a warning light/symbol or message on the instrument panel. In any case, never exceed 20,000 km, or 1 year. (2) Areas that are not dusty: recommended maximum distance 120,000 km.
  • Page 323 SERVICE SCHEDULE (Plug-in Hybrid version) WARNING Once you have carried out the last intervention in the table, continue with the scheduled servicing, maintaining the frequency indicated in the plan by marking each operation with a dot or dedicated note. Warning: simply restarting the maintenance from the start of the plan may cause the allowed interval to be exceeded for some operations!  ...
  • Page 324 Thousands of miles Thousands of kilometres Years Visually inspect conditions and wear of front and rear disc brake pads and integrity of pad wear indicator Visually inspect the condition of the accessory drive belt(s) (3) Visual inspection of electrical charging socket condition and integrity Change engine oil and replace oil filter Spark plug replacement(5) Replace accessory drive belt/s...
  • Page 325 (see the "Engine" chapter in the "Technical Specifications" section); strictly comply with the spark plugs replacement intervals in the Service Schedule. It is advisable to contact a Jeep Dealership for plug replacement.

  • Page 326: Engine Compartment

    ENGINE COMPARTMENT Version 1.3 5520590D 1. Engine oil level dipstick 2. Engine oil cap/filler 3. Engine coolant 4. Windscreen/rear window washer fluid 5. Brake fluid 6. Conventional battery...
  • Page 327 1.3 190/240 HP version (Plug-in Hybrid version) 5520742D 1. Engine oil level dipstick 2. Engine oil cap/filler 3. Heat engine coolant 4. Windscreen/rear window washer fluid 5. Brake fluid 6. Conventional battery 7. High-voltage system coolant...
  • Page 328 1. Engine oil level dipstick 2. Engine oil cap/filler 3. Engine coolant 4. Windscreen/rear window washer fluid 5. Brake fluid 6. Conventional battery NOTE The cooling tank of the high-voltage system cannot be refilled by the driver. If it is necessary to top up the fluids, contact a Jeep Dealership.
  • Page 329 MIN and ENGINE COOLANT The transmission control oil level should MAX marks on the dipstick. only be checked at a Jeep Dealership. 421) Version 1.3 CONVENTIONAL FLAT BATTERY The engine oil level dipstick (1) is...
  • Page 330 10 minutes. Have the system lights, etc.) before carrying out any work another original or the operation of the inspected at a Jeep Dealership before on the electrical system, disconnect the system may be adversely affected. Do not the summer.
  • Page 331 It is advisable to contact during connection. Wash the affected itself. Do not use a quick battery charger a Jeep Dealership to have the fluid to provide the starting voltage. area immediately with plenty of water in changed.

  • Page 332: Charging The Conventional Battery

    To change the oil and after having disconnected the battery is used with the battery fitted on the car, filters, it is advisable to contact a Jeep before connecting it disconnect both charger, reconnect connector (1) to the Dealership.

  • Page 333: Servicing Procedures

    Periodically clean the windscreen and the air conditioning system must 147) rear window and rubber profile of the be checked and serviced at a Jeep To ensure correct engine lubrication, the windscreen/rear window wiper blades, Dealership at the beginning of the...
  • Page 334 WARNING Do not operate the rear is in the full up position. checked at a Jeep Dealership. window wiper with the blade lifted from Position the windscreen wiper blade the rear window.
  • Page 335 (antifreeze) cleaned new brake fluid or fluid stored in a In normal car operating conditions, it is and washed by a Jeep Dealership. completely closed container. Brake fluid not necessary to change the transmission stored in an open container absorbs Engine cooling system radiator cap fluid.
  • Page 336 Jeep Dealership. carried out by a Jeep Dealership. bonnet until the radiator has cooled. 145) The car is filled with fluids Never attempt to remove the cap with...

  • Page 337: Raising The Car

    If the car is to be lifted, go to a Jeep Fit chains on the front wheels only. every 10000/15000 kilometres switch Dealership which is equipped with the...
  • Page 338 steering, manoeuvres and braking. For 453) If tyre pressure is too low, it may burst and injure someone. Do not attempt this reason they are subject to uneven overheat and be severely damaged as a to release the car with accelerations faster wear.

  • Page 339: Car Inactivity

    CAR INACTIVITY too fast for conditions also creates the IMPORTANT possibility of loss of car control. If the car is left inactive for longer than a 466) The space-saver spare wheel and month, the following precautions should 154) Replacing original tyres with tyres the folding spare wheel are for temporary be observed: of a different size may result in false...

  • Page 340: Bodywork

    (where provided) it periodically; The Jeep Dealership can provide further Some parts of the car are painted with do not drain the engine cooling advice on what to do if the car should be a matt paintwork which requires special system;...
  • Page 341 UNDERBODY WASHING WARNINGS operation performed at a specialised workshop. (Plug-In Hybrid versions) Avoid parking under trees; the resin dropped by trees makes the paintwork go If it is necessary to wash the underbody, WARNING The washing should take opaque and increases the possibility of do not directly pressurize with a high- place with the engine cold and the pressure jet.

  • Page 342: Interior

    original appearance and colour of the the front windscreen and rear window; that complete protection against water components. dilute it min. 50% with water. Only use seepages cannot be guaranteed. pure screen washer fluid when strictly Remove any dust using a microfibre necessary due to outside temperature cloth, if necessary moistened with IMPORTANT...
  • Page 343 IMPORTANT 163) Never use alcohol, petrols and derivatives to clean the dashboard and instrument panel lens.
  • Page 344 Blank page...
  • Page 345 TECHNICAL SPECIFICATIONS Everything you may find useful for IDENTIFICATION DATA ..344 understanding how your vehicle is made MOTOR AND HIGH-VOLTAGE and works is contained in this section BATTERIES ....345 and illustrated with data, tables and TRANSMISSION .

  • Page 346: Identification Data

    IDENTIFICATION DATA Chassis number The chassis number (VIN) is indicated in the front left corner of the windscreen and can be seen from outside the car (fig. 338). This numbers is also printed on the front right part of the body, on the front floor (fig.

  • Page 347: Motor And High-Voltage Batteries

    MOTOR AND HIGH-VOLTAGE BATTERIES   Versions 1.3-litre 130 HP 1.3 150 HP 1.6 Multijet 130 HP Engine code 55282328 55282328 46346020 Cycle Otto Otto Diesel Number and position of cylinders 4 in line 4 in line 4 in line Piston bore and stroke (mm) 70 x 86.5 70 x 86.5 79.5 x 80.5...
  • Page 348   PLUG-IN HYBRID VERSION Versions 1.3 190 HP (*) 1.3 240 HP (*) Engine code 46337540 46337540 Cycle Otto Otto Number and position of cylinders 4 in line 4 in line Piston bore and stroke (mm) 70 x 86.5 70 x 86.5 Total displacement (cm³) 1332 1332...
  • Page 349 Features Maximum torque (Nm) (*) The peak power that the electric motor can supply may be higher than the continuous power, depending on various factors such as the state of charge of the high-voltage battery and the environmental conditions. HIGH-VOLTAGE BATTERIES Features Battery type Lithium ions...

  • Page 350: Transmission

    TRANSMISSION Versions with mechanical gearbox Versions Transmission Clutch Traction 1.3-litre 130 HP Six forward gears plus reverse Self-adjusting pedal without with synchronisers for forward Front idle stroke 1.6 16V Multijet 130HP gears and reverse Versions with dual clutch automatic transmission Versions Transmission Traction...

  • Page 351: Dimensions

    DIMENSIONS Dimensions are expressed in mm and refer to the car equipped with its original tyres. Height is measured with car unladen. 5520824D   1624 (*) / 1629 (**) / 4404 2636 1638 (*)(***) 1547 2033 1542 1819 / 1644 (**) (***) (*) Without roof rack bars (**) With roof rack bars...
  • Page 352   5520462D   Minimum ground clearance / typical angles Minimum ground clearance Approach angle (B) Departure angle (C) Breakover angle (D) - mm (A) 1.3 130 HP (*) 15.8° 30.8° 21.8° 1.3 150 HP (**) 15.8° 30.8° 21.8° 1.3 190 HP /1.3 240 HP 201 / 213 (****) 16°...
  • Page 353 Approach angle (Reference B) The approach angle is determined by the horizontal line of the road surface and by the tangent line passing between the front wheel and the most projecting low point of the car. The wider the angle, the lower the chance to hit an obstacle with the body or chassis, when climbing a steep slope or overcoming an obstacle.

  • Page 354: Rims And Wheels

    RIMS AND WHEELS winter equipment; therefore their use is 215 Nominal width (S, distance in mm equivalent to that of the snow chains. between sides) 473) 474) The snow chains may be applied only to 65 Height/width ratio (H/S), expressed as Alloy rims, tubeless radial tyres.
  • Page 355 97 = 730 kg checked with a torque wrench at the J0A0010 78 = 425 kg 98 = 750 kg Jeep Dealership or a service station. WHEEL AND TYRE TIGHTENING TORQUES 79 = 437 kg It is very important that the tightening...
  • Page 356 After 40 km, have the tightening torque of the fixing bolts checked and check that they are properly seated in the wheel. 478)
  • Page 357 RIMS AND TYRES PROVIDED 473) 474)   Versions Rims Tyres Snow tyres 6.5J x 16 ET40 (*) 215/65 R16 98H (*) 215/65 R16 98Q (M+S) 215/60 R17 96H 7J x 17 ET37.5 215/60 R17 96Q (M+S) 215/60 R17 96V 1.3 130 HP 1.3 150 HP 225/55 R18 98V 7J x 18 ET37.5...
  • Page 358 Versions Rims Tyres Snow tyres 6.5J x17 H2 ET40 215/60 R17 96H (M+S) Spare wheel (optional) 6.5J x17 H2 ET40 215/65 R17 99S (M+S) (**) (*) Where provided (**) Plug-in Hybrid version (***) Only for using 7 mm snow chains WARNING The spare wheel fitted the speed of the vehicle must not exceed 80 km/h: for more information refer to the on "Changing a wheel"...
  • Page 359 COLD TYRE INFLATION PRESSURE When the tyres are warm, the inflation pressure should be + 0.3 bar in relation to the recommended figure. However, recheck the correct value when the tyre is cold. With snow tyres, add +0.2 bar to the pressure value prescribed for standard tyres. If it is necessary to raise the car, refer to the "Raising the car"...
  • Page 360 Plug-in Hybrid version   Unladen/medium load Full load Tyres Front Rear Front Rear 215/60 R17 96H (*) 235/60 R17 102H (***) 235/55 R18 100H (***) 235/45 R19 XL 99H (***) 215/65 R17 99S (**) (*) Non original tyre: it must only be fitted if 7 mm snow chains are to be used. (**) Spare wheel (optional) (***) The indicated pressure is aimed at comfort.

  • Page 361: Weights And Loads

    WEIGHTS AND LOADS E.g.: E= 3400 kg - D= 2400 kg WARNING Braked trailer = 1000 kg + 250 kg (SAE To identify the weights and loads towing)(*) for this vehicle, refer to the plate 475) DO NOT fit wheel hub caps when ATTENTION Do not exceed the indicated shown in fig.
  • Page 362   TOWABLE WEIGHTS (kg) Versions 1.3 130 HP / 150 HP 1965 1750 1.3 190 HP/240 HP (Plug-In Hybrid) 2400 1250 1.6 Multijet 130 HP 2086 1250 Key: A = TOWABLE WEIGHT B = UNBRAKED TRAILER C = LOAD ON TOW HOOK D = LOAD ON ROOF (versions with roof rack bars)

  • Page 363: Refuelling

    (**) When the vehicle is used in particularly harsh weather conditions, we recommend using a 60% mixture of PARAFLU UP and 40% demineralised water. (***) NOTE The cooling tank for the high-voltage system cannot be refilled by the driver. If it is necessary to top up the fluids, contact a Jeep Dealership.
  • Page 364   Prescribed fuels and original 1.6-litre 16V Multijet lubricants Fuel tank (liters): Diesel for motor vehicles (EN590 Specification) Including a reserve of (litres): AdBlue ® (DIN 70 070 and ISO AdBlue® tank (where provided) capacity approximately (litres): 22241-1 specifications) Mixture of demineralised water and Engine cooling system (litres): 50% PARAFLU UP (*) Engine sump and filter (litres):...

  • Page 365: Fluids And Lubricants

    FLUIDS AND LUBRICANTS The engine oil used in your vehicle has been carefully developed and tested to meet the requirements of the Scheduled Servicing Plan. Always using the lubricants specified will ensure that the vehicle meets the stated consumption and emissions performances. The quality of the lubricant is a key factor in the operation and life of the engine.
  • Page 366 Original liquids and Features Specification Applications lubricants SAE 75W API GL4 grade Electrified axle synthetic lubricant TUTELA TRANSMISSION SAE 75W API GL4 grade GEARFORCE Manual gearbox and 9.55550-MZ6 synthetic lubricant. Contractual Technical differential Reference N° F002.F10 Lubricants and greases for Molybdenum disulphide drive transmission TUTELA ALL STAR...
  • Page 367 Original liquids and Features Specification Applications lubricants PETRONAS DURANCE DIESEL Antifreeze additive for To be mixed with diesel (25 Diesel fuel additive diesel, with protective Contractual Technical cc per 10 litres) action for Diesel engines Reference N° F601.L06 Red protective with antifreeze action, based on PARAFLU UP inhibited monoethyl glycol...

  • Page 368: Performance

    PERFORMANCE Top speed achievable after the car break-in period.   Versions km/h 1.3-litre 130 HP 1.3 150 HP 1.3 190 HP(*) 184 (**)/ 135 (***) 1.3 240 HP(*) 200 (**)/ 135 (***) 1.6 16V Multijet 130HP (*) Plug-in Hybrid version (**) Hybrid mode (***) Electric mode...

  • Page 369: Fuel Consumption And Co 2 Emissions

    FUEL CONSUMPTION AND CO 2 EMISSIONS The fuel consumption and CO emission figures declared by the manufacturer are determined on the basis of the type-approval tests laid down by the applicable standards in the country where the vehicle is registered. Type of route, traffic, weather conditions, driving style, general condition of the vehicle, level of equipment/accessories, use of the climate control system, vehicle load, presence of roof rack, and other situations that negatively affect the aerodynamics or resistance will lead to different consumption values.

  • Page 370: End Of Its Life

    PRESCRIPTIONS FOR HANDLING THE CAR AT THE END OF ITS LIFE (where present) FCA has been committed for many years to safeguarding the environment through the constant improvement of its production processes and manufacturing products that are increasingly "eco-compatible". To grant customers the best possible service in terms of respecting environmental laws and in response to European Directive 2000/53/EC governing vehicles at the end of their life, FCA is offering its customers the chance to hand over their vehicle at the end of its life without incurring any additional costs.
  • Page 371 MULTIMEDIA TIPS, CONTROLS AND GENERAL INFO ....370 This section describes the main Uconnect™ ....372 functions of the Uconnect™...

  • Page 372: Tips, Controls And General Info

    In case you lose the car radio passport, which could damage its surface; use a or if the electronic control unit (Body please go to Jeep Dealership with an ID soft, dry anti-static cloth to clean and do Computer) is replaced, the system will and the car papers.
  • Page 373 Immediately stop using the system in the event of a fault. Otherwise the system might be damaged. Contact a Jeep Dealership as soon as possible to have the system repaired. WARNING 479) Follow the safety rules below: otherwise serious injuries may occur to the occupants or the system may be damaged.

  • Page 374: Uconnect

    Uconnect™ Version with navigation system (10.1") 5520565D...
  • Page 375 Version without navigation system: (A) 10.1"/ (B) 8.4" 5520861D...
  • Page 376 GRAPHIC BUTTONS ON DISPLAY AREA (1)   Graphic button Functions Mode - Home Show the main screen Press graphic button Access Media mode to select available - Media sources, folder tracks and interaction with Press graphic button audio settings Climate control system settings (air flow, set - Comfort indoor temperature) and heated seat (where Press graphic button...
  • Page 377 STATUS BAR   Area Functions Mode Climate control system display and settings on Comfort (where provided) Press graphic button driver and passenger side Quick access to functions: Profiles, Reconfigurable quick button bar Notifications, External temperature (where Press graphic button provided), Voice recognition (where provided) Display the current time / access to the Apps Timetable / App customisation Press graphic button...
  • Page 378 STEERING WHEEL CONTROLS The controls for the main system functions are present on the steering wheel to make control easier. 5520669D Steering wheel controls summary table Button Interaction Acceptance of incoming call Acceptance of the second incoming call and putting the active call on hold Display on the instrument panel of the list of the last 10 calls and favourite phone numbers (only with call browsing enabled) Activation of voice recognition, where provided or via CarPlay or Android Auto...
  • Page 379 CONTROLS BEHIND THE STEERING WHEEL   Buttons Interaction Button 2 (steering wheel left side) Brief button press: search for next radio station or selection of USB next track. Upper button Long button press: scan of higher frequencies until released/fast forward of USB track.
  • Page 380 CENTRAL DASHBOARD CONTROLS 5520740D   Control Function Turn knob: increase/decrease volume Press button: Uconnect™ on/off button Turn knob: tune radio stations / select audio track / select menu item Press button: confirm selection Turn the Uconnect™ display on/off Activate/deactivate Mute function...
  • Page 381 TOUCHSCREEN FUNCTION HOT BUTTONS Middle part: Display of information about the track or station being played and The system uses the touchscreen Up to 2 hot buttons (3) fig. 349 can be playback control buttons: function; to interact with the different set on the status bar.
  • Page 382 Within each list, the "ABC" graphic temperature synchronisation and The "Device Manager" can be accessed button allows the user to skip to the driver/passenger side ventilation (Sync). directly from the "Phone" function. desired letter in the list. BLUETOOTH® MODE NOTE Up to 20 device can be paired. NOTE This button might be disabled for This mode is activated by pairing a In case of an attempt to pair a twenty-...
  • Page 383 When a USB device is plug into the view received text messages (where You can make a call by selecting one of port on the dashboard with the radio provided); the following items: on, it starts to play the tracks on the view the connected devices.
  • Page 384 NOTE On some mobile phones, to make answer a received message or as a new intuitively. To enable them, connect a the text voice reading function available, message. compatible smartphone to the USB the text notification option on the phone port of the car or in Wireless mode must be enabled;...
  • Page 385 You can Android Auto: To interact with Android "Jeep" or "Hey Uconnect" (if the user has only perform this procedure with the car Auto press the steering wheel button previously enabled the function, for stationary.
  • Page 386 HYBRID ELECTRIC PAGES Text set air temperature value inside the (where provided) passenger compartment). Send a message to <contact> mobile / Proceed as follows: work select the "Vehicle” graphic button Media on the Uconnect™ and then select "E- I want to listen to music Hybrid";...
  • Page 387 Regeneration Charging Schedule The graphic bars on the display show Using this function you can set the high- the value of energy recovered from the voltage battery charging by selecting the high-voltage battery (expressed in kWh) following settings: during "eCoasting" and "eBraking" energy "Start Time": time at which to activate recovery operations.
  • Page 388 For the charging cable connection, see NOTE Before the comfort temperature Ignition device in the STOP position; the description in the "Charging" chapter is reached, press and release the door Automatic transmission gear lever in in the "Knowing your car" section. "Park"...
  • Page 389 ranges from a minimum level ("Lvl "1') Charging time the high-voltage battery having a state of up to a maximum level ('Lvl 5"). charge less than 1%. The charging time varies depending on: Type of charging cable used: "Mode 2” (*) The high-voltage battery state of charge the high-voltage battery state of (expressed as a percentage) is shown...
  • Page 390 (**) The specified standard charge You can choose to view the route via a "Drive to work": Select this button time is calculated for the maximum 3D image in the "Guidance view". to navigate to the location level (5) “high” set on the Uconnect™ registered as "Work".
  • Page 391   Planning a route - Finding a public You can select a charging station from charging station the list to find it on the map. After selecting a destination, Tip: You can scroll down the list of WARNING In the interest of safety and clicking on a point on the map results using the scroll bar on the right or using the search function,...
  • Page 392 “Settings” page. Favourites The navigation system can also be updated at the Jeep Dealership. The "Favourites" submenu contains (for The settings are available if the car versions/markets, where provided) the speed is below 8 km/h.
  • Page 393 To add or remove an app from the the button on the display and select Favourites list, select or deselect the star the desired Widget from the list. that appears on the app icon in the list Some Widgets can also be customised by shown in the "Recent", "Categories"...
  • Page 394 You can exclude all profiles and keep the arrows on the screen to set the the default settings by pressing on the desired time. "Valet" mode, using the button on the "All profiles" page. UPDATING THE SYSTEM The Uconnect™ system can be updated remotely via Over The Air upgrade.

  • Page 395: Connected Services - Uconnect Services

    Read more restored. During the update, a second pop-up about the general conditions of service In this case, contact a Jeep Dealership. screen shows the estimated time and data protection policies on the Jeep remaining and the progress percentage official website.
  • Page 396 Services, including the HELP and go to the personal page on the official It notifies any malfunctions of the car on ASSIST calls, is subject to mobile Jeep website. the Uconnect™ system. My Remote: this can be used to network and GPS geolocation coverage,...
  • Page 397 NOTE The hotspot name and password profile from the services on the page on only tracked by the navigation, safety, can only be changed with the ignition the official Jeep website, by contacting...

  • Page 398: Official Type Approvals

    OFFICIAL TYPE the Customer Care or by going to a Jeep Dealership. APPROVALS You will also be responsible for informing the new owner of any services which have not yet expired associated with a All radio equipment provided with the new Uconnect Services account.
  • Page 400 Fully synthetic lubricant developed for American design petrol engines Fully synthetic Low SAPS lubricant for Euro 6 diesel engines. High fuel economy.
  • Page 402 MAINTAIN YOUR VEHICLE IN TIP TOP CONDITIONS WITH Mopar Vehicle Protection offers a series of service contracts that are designed to give all our customers the pleasure of driving their vehicle without any hitch's and concerns. Our product portfolio consists of a wide and flexible range of extended warranty and maintenance plans endorsed by FCA.
  • Page 403 NOTES...
  • Page 405 ....43 Jeep Active Drive (4WD) ..198 luids and lubricants ..363 emissions .
  • Page 406 aneSense ....223 Rear window wiper/washer ..39 Towing a broken-down car ..307 Towing for tourism (towing of Rear-view mirrors .
  • Page 407 We really know the vehicle because we invented, designed and produced it: we know every minor detail of it. At the Jeep authorised workshops you will fi nd technicians directly trained by us, providing quality and professionalism needed for all service operations.
  • Page 408 The data contained in this publication is intended merely as a guide. FCA Italy S.p.A. reserves the right to modify the models and versions described in this booklet at any time for technical and commercial reasons. If you have any further questions please consult your JEEP dealer.

Table of Contents

Save PDF