Page 1 Compass 2 0 1 2 O W N E R ’ S M A N U A L...
Page 2 VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name This manual illustrates and describes the operation of fea- Chrysler Group LLC shall be deemed to be deleted and the tures and equipment that are either standard or optional on name Chrysler Canada Inc.
Page 3: Table Of Contents
TABLE OF CONTENTS SECTION PAGE ............3 INTRODUCTION .
Page 5 INTRODUCTION CONTENTS Introduction ......4 Warnings And Cautions ....7 Rollover Warning .
Page 6: Introduction
4 INTRODUCTION INTRODUCTION When it comes to service, remember that your authorized Congratulations on selecting your new Chrysler Group dealer knows your vehicle best, has factory-trained tech- LLC vehicle. Be assured that it represents precision nicians and genuine MOPAR parts, and cares about workmanship, distinctive styling, and high quality - all your satisfaction.
Page 7: How To Use This Manual
INTRODUCTION 5 control. Failure to operate this vehicle safely may result seat belts could cut the highway death toll by 10,000 or in a collision, rollover of the vehicle, and severe or fatal more each year and could reduce disabling injuries by injury.
Page 8 6 INTRODUCTION...
Page 9: Warnings And Cautions
INTRODUCTION 7 WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against op- erating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information.
Page 10: Vehicle Modifications/Alterations
8 INTRODUCTION VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. Right Front Body VIN Location NOTE: It is illegal to remove or alter the VIN.
Page 11: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Vehicle Security Alarm — If Equipped ..18 Ignition Key Removal .
Page 12 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Illuminated Approach — If Equipped ..21 Child-Protection Door Lock System — Rear Doors ......33 To Lock The Doors And Liftgate .
Page 13 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 Automatic Locking Retractor Mode Air Bag Deployment Sensors And Controls . . . 66 (ALR) — If Equipped ....52 Event Data Recorder (EDR) .
Page 14: Things To Know Before Starting Your Vehicle 9
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Ignition Key Removal The authorized dealer that sold you your new vehicle has 1. Place the shift lever in PARK (if equipped with an the key code numbers for your vehicle locks. These automatic transmission).
Page 15 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 NOTE: If you try to remove the key before you place the shift lever in PARK, the key may become trapped tem- porarily in the ignition switch cylinder. If this occurs, place the shift lever in PARK, rotate the key to the right slightly, then remove the key as described.
Page 16: Locking Doors With A Key
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) CAUTION! • Allowing children to be in a vehicle unattended is An unlocked car is an invitation to thieves. Always dangerous for a number of reasons. A child or remove the key from the ignition and lock all the others could be seriously or fatally injured.
Page 17: Sentry Key
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 SENTRY KEY seconds for a bulb check. If the light remains on after the The Sentry Key Immobilizer System prevents unauthor- bulb check, it indicates that there is a problem with the ized vehicle operation by disabling the engine.
Page 18: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE All of the keys provided with your new vehicle have dealer or by following the customer key programming been programmed to the vehicle electronics. procedure. This procedure consists of programming a blank key to the vehicle electronics. A blank key is one Replacement Keys that has never been programmed.
Page 19: General Information
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 3. Insert the second valid key into the ignition switch. Repeat this procedure to program up to eight keys. If you Turn the ignition switch to the ON/RUN position within do not have a programmed Sentry Key , contact your 15 seconds.
Page 20: Vehicle Security Alarm - If Equipped
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE VEHICLE SECURITY ALARM — IF EQUIPPED 3. The Vehicle Security Light in the instrument cluster This Vehicle Security Alarm monitors the doors, liftgate, will flash rapidly for approximately 16 seconds. This and ignition switch for unauthorized operation. shows that the Vehicle Security Alarm is arming.
Page 21: Vehicle Security Alarm Manual Override
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 If something has triggered the Vehicle Security Alarm in REMOTE KEYLESS ENTRY (RKE) — IF EQUIPPED your absence, the horn will sound three times and This system allows you to lock or unlock the doors and exterior lights blink three times when you unlock the liftgate or activate the Panic Alarm from distances up to doors.
Page 22: To Unlock The Doors And Liftgate
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles not equipped with the EVIC, perform the NOTE: The line of transmission must not be blocked with metal objects. following steps: To Unlock The Doors And Liftgate 1. Press and hold the LOCK button on a programmed Press and release the UNLOCK button on the RKE RKE transmitter for at least 4 seconds, but no longer than transmitter once to unlock the driver’s door, or twice...
Page 23: Illuminated Approach - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Security Alarm activated will cause the alarm to sound. To Lock The Doors And Liftgate Press the UNLOCK button to deactivate the Vehicle Press and release the LOCK button on the RKE transmit- Security Alarm.
Page 24: Flash Lights With Remote Key Lock/Unlock
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles not equipped with the EVIC, perform the NOTE: Pressing the LOCK button on the RKE transmit- following steps: ter while you are in the vehicle will activate the Vehicle Security Alarm.
Page 25: Using The Panic Alarm
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 • For vehicles not equipped with the EVIC, perform the Alarm activated will cause the alarm to sound. Press the following steps: UNLOCK button to deactivate the Vehicle Security Alarm. 1. Press and hold the UNLOCK button on a programmed RKE transmitter for at least 4 seconds, but no longer than Using The Panic Alarm 10 seconds.
Page 26: Programming Additional Transmitters
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Programming Additional Transmitters If your RKE transmitter fails to operate from a normal Refer to Sentry Key “Customer Key Programming.” distance, check for these two conditions: If you do not have a programmed RKE transmitter, 1.
Page 27: Remote Starting System - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 NOTE: If the RKE transmitter is equipped with a screw, reinstall and tighten the screw until snug. REMOTE STARTING SYSTEM — IF EQUIPPED This system uses the Remote Keyless Entry (RKE) transmitter to start the engine conve- niently from outside the vehicle while still maintaining security.
Page 28: How To Use Remote Start
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Use Remote Start WARNING! All of the following conditions must be met before the • Do not start or run an engine in a closed garage or engine will remote start: confined area.
Page 29: To Enter Remote Start
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 • Remote Start Aborted — Hood Ajar • For security, power window and power sunroof op- eration (if equipped) are disabled when the vehicle is • Remote Start Aborted — L/Gate Ajar in the Remote Start mode.
Page 30: To Exit Remote Start Without Driving
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The hazard switch is pressed To Exit Remote Start Mode And Drive The Vehicle Before the end of the 15-minute cycle, press and release • The transmission is moved out of PARK the UNLOCK button on the RKE transmitter to unlock •...
Page 31: Door Locks
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 DOOR LOCKS WARNING! Manual Door Locks • For personal security and safety in the event of an Use the manual door lock knob to lock the doors from accident, lock the vehicle doors as you drive as inside the vehicle.
Page 32: Power Door Locks
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE is in the ignition and either front door is open. A chime WARNING! (Continued) will sound as a reminder to remove the key. • Do not leave the key fob in or near the vehicle, and do not leave the ignition in the ACC or ON/RUN position.
Page 33 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 when the vehicle’s speed exceeds 15 mph (24 km/h). The 2. Within 15 seconds, cycle the ignition switch between auto door lock feature can be enabled or disabled by your LOCK and ON/RUN and then back to LOCK four times authorized dealer.
Page 34 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Unlock Doors On Exit Equipped/Personal Settings (Customer-Program- The doors will unlock automatically if: mable Features)” in “Understanding Your Instrument Panel” for further information. 1. The Automatic Unlock Doors On Exit feature is en- •...
Page 35: Child-Protection Door Lock System - Rear Doors
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 NOTE: 3. Repeat steps 1 and 2 for the opposite rear door. • If you do not hear the chime it means that the system did not enter the programming mode and you will need to repeat the procedure.
Page 36: Power Windows - If Equipped
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: For emergency exit with the system engaged, move the lock knob up (unlocked position), roll down the window and open the door with the outside door handle. POWER WINDOWS — IF EQUIPPED Power Window Switches The window controls on the driver’s door trim panel control all the door windows.
Page 37: Auto-Down
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 • For vehicles equipped with the EVIC, the power window switches will remain active for up to 10 min- utes after the ignition switch is turned to the LOCK position. Opening either front door will cancel this feature.
Page 38: Window Lockout Switch
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Window Lockout Switch LIFTGATE The window lockout switch on the driver’s door allows NOTE: The key that is used to start the vehicle is also you to disable the window control on the other doors. To used to lock or unlock the doors and open the liftgate.
Page 39 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 • Although the liftgate has no inside release mechanism, the liftgate trim panel includes an opening with a snap-in cap that provides access to release the latch in the event of an electrical system malfunction. WARNING! •...
Page 40: Occupant Restraints
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Supplemental Seat-Mounted Side Air Bags (SAB) — if Gas props support the liftgate in the open position. However, because the gas pressure drops with tempera- equipped ture, it may be necessary to assist the props when •...
Page 41 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 If you will be carrying children too small for adult-sized WARNING! seat belts, the seat belts or the Lower Anchors and Tether for CHildren (LATCH) feature also can be used to hold Infants in rear facing child restraints should never infant and child restraint systems.
Page 42 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If a child from 1 to 12 years old (not in a rear facing child 5. If the air bag system in this vehicle needs to be seat) must ride in the front passenger seat, move the seat modified to accommodate a disabled person, contact as far back as possible and use the proper child restraint.
Page 43 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Buckle up even though you are an excellent driver, even WARNING! (Continued) on short trips. Someone on the road may be a poor driver • Being too close to the steering wheel or instrument and cause a collision that includes you.
Page 44: Lap/Shoulder Belts
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belts WARNING! (Continued) All seating positions in your vehicle are equipped with • Do not allow people to ride in any area of your lap/shoulder belts. vehicle that is not equipped with seats and seat The belt webbing retractor is designed to lock during belts.
Page 45 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 WARNING! (Continued) • Two people should never be belted into a single seat belt. People belted together can crash into one another in a collision, hurting one another badly. Never use a lap/shoulder belt or lap belt for more than one person, no matter what their size.
Page 46 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch WARNING! plate into the buckle until you hear a “click.” • A belt that is buckled into the wrong buckle will not protect you properly.
Page 47 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 4. Position the lap belt across your thighs, below your WARNING! (Continued) abdomen. To remove slack in the lap belt portion, pull up • A belt that is worn under your arm is dangerous. on the shoulder belt.
Page 48 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. WARNING! The belt will automatically retract to its stowed position. • A lap belt worn too high can increase the risk of If necessary, slide the latch plate down the webbing to allow the belt to retract fully.
Page 49: Adjustable Upper Shoulder Belt Anchorage
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 Adjustable Upper Shoulder Belt Anchorage In the front seat, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Push the anchorage button to release the anchorage, and move it up or down to the position that fits you best.
Page 50: Second Row Center Lap/Shoulder Belt Operating Instructions
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In the rear seat, move toward the center of the seat to position the belt away from your neck. Second Row Center Lap/Shoulder Belt Operating Instructions The second row center lap/shoulder belt features a three-point seat belt with a mini-latch and buckle, which allows the shoulder belt to detach from the lower anchor when the seat is folded.
Page 51 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 6. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Routing The Rear Center Shoulder Belt 4. When the belt is long enough to fit, insert the mini- latch plate into the mini-buckle until you hear a “click.”...
Page 52 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 7. Position the lap belt across your thighs, below your 8. Position the shoulder belt on your chest so that it is abdomen. To remove slack in the lap belt portion, pull up comfortable and not resting on your neck.
Page 53: Lap/Shoulder Belt Untwisting Procedure
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 10. To disengage the mini-latch from the mini-buckle for 4. Continue to slide the latch plate up until it clears the storage, insert the regular latch plate into the black folded webbing. button on the top of the mini-buckle.
Page 54: Automatic Locking Retractor Mode (Alr) - If Equipped
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the passenger seating position is equipped with an position that has a belt with this feature. Children ALR and is being used for normal usage: 12 years old and under should always be properly restrained in the rear seat.
Page 55: Energy Management Feature
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 Seat Belt Pretensioners WARNING! The seat belts for both front seating positions are • The belt and retractor assembly must be replaced equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. if the seat belt assembly Automatic Locking Re- These devices may improve the performance of the seat tractor (ALR) feature or any other seat belt func-...
Page 56: Supplemental Active Head Restraints (Ahr) - If Equipped
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Active Head Restraints (AHR) — If When AHRs deploy during a rear impact, the front half Equipped of the head restraint extends forward to minimize the gap These head restraints are passive, deployable compo- between the back of the occupant’s head and the AHR.
Page 57 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 CAUTION! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision.
Page 58 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Grasp the deployed AHR from the rear seat. 3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. Hand Positioning Points On AHR 2.
Page 59 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 AHR In Reset Position 3 — Final Downward Movement To Engage Locking Mechanism NOTE: 4. The AHR front soft foam and trim half should lock • If you have difficulties or problems resetting the into the back decorative plastic half.
Page 60: Enhanced Seat Belt Use Reminder System (Beltalert )
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Seat Belt Use Reminder System unbuckled while traveling at speeds greater than 5 mph (BeltAlert ) (8 km/h), BeltAlert will provide both audio and visual BeltAlert is a feature intended to remind the driver and notification.
Page 61: Seat Belt Extender
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 Seat Belt Extender Seat Belts And Pregnant Women If a seat belt is too short, even when fully extended, and We recommend that pregnant women use the seat belts when the adjustable upper shoulder belt anchorage (if throughout their pregnancy.
Page 62: Supplemental Restraint System (Srs) - Air Bags
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Restraint System (SRS) — Air Bags This vehicle has Advanced Front Air Bags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s Advanced Front Air Bag is mounted in the center of the steering wheel.
Page 63 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 The Advanced Front Air Bags have a multistage inflator This vehicle may be equipped with Supplemental Seat- design. This allows the air bag to have different rates of Mounted Side Air Bags (SAB) to provide enhanced inflation that are based on the severity and type of protection for an occupant during a side impact.
Page 64: Advanced Front Air Bag Features
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Instrument Panel Advanced Front Air Bag Features The Advanced Front Air Bag system has multistage • Knee Impact Bolster driver and front passenger air bags. This system provides • Driver Advanced Front Air Bag output appropriate to the severity and type of collision as determined by the Occupant Restraint Controller (ORC), •...
Page 65 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 Supplemental Seat-Mounted Side Air Bags WARNING! (SAB) — If Equipped • No objects should be placed over or near the air Supplemental Seat-Mounted Side Air Bags (SAB) may bag on the instrument panel, because any such provide enhanced protection to help protect an occupant objects could cause harm if the vehicle is in a during a side impact.
Page 66 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE When the air bag deploys, it opens the seam between the front and side of the seat’s trim cover. Each air bag deploys independently; a left side impact deploys the left air bag only and a right-side impact deploys the right air bag only.
Page 67 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 • Being too close to the Supplemental Side Air Bag WARNING! (Continued) Inflatable Curtain and/or Seat-Mounted Side Air Bag • Do not use accessory seat covers or place objects during deployment could cause you to be severely between you and the side air bags;...
Page 68: Air Bag Deployment Sensors And Controls
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Along with seat belts and pretensioners, Advanced Front Advanced Front Air Bags are designed to provide addi- Air Bags work with the knee bolsters to provide im- tional protection by supplementing the seat belts in proved protection for the driver and front passenger.
Page 69 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 Because air bag sensors measure vehicle deceleration Also, the ORC turns on the Air Bag Warning over time, vehicle speed and damage by themselves are Light in the instrument panel for approxi- not good indicators of whether or not an air bag should mately four to eight seconds for a self-check have deployed.
Page 70 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE are possible, based on the collision type and severity. The WARNING! steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as Ignoring the Air Bag Warning Light in your instru- the air bags inflate to their full size.
Page 71 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 Based on the severity and type of collision, the side air A quantity of non-toxic gas is generated to inflate the side bag inflator on the crash side of the vehicle may be curtain air bag.
Page 72 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Turn on the interior lights, which remain on as long as Front And Side Impact Sensors In front and side impacts, impact sensors can aid the the battery has power or until the ignition key is ORC in determining appropriate response to impact removed.
Page 73 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 If you do have a collision, which deploys the air bags, any throat irritation, move to fresh air. If the irritation or all of the following may occur: continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s in- •...
Page 74 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Air Bag System WARNING! (Continued) • Do not attempt to modify any part of your air bag WARNING! system. The air bag may inflate accidentally or • Modifications to any part of the air bag system may not function properly if modifications are could cause it to fail when you need it.
Page 75: Event Data Recorder (Edr)
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Air Bag Warning Light NOTE: If the speedometer, tachometer, or any engine You will want to have the air bags ready to related gauges are not working, the Occupant Restraint inflate for your protection in a collision. The Controller (ORC) may also be disabled.
Page 76: Child Restraints
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Whether or not the driver and passenger safety belts To read data recorded by an EDR, special equipment is were buckled/fastened; required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer, other parties, •...
Page 77 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 The infant carrier is only used rearward-facing in the WARNING! vehicle. It is recommended for children from birth until they reach the weight or height limit of the infant carrier. In a collision, an unrestrained child, even a tiny baby, Convertible child seats can be used either rearward- can become a projectile inside the vehicle.
Page 78 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE in the vehicle by the lap/shoulder belt or the LATCH WARNING! child restraint anchorage system. Refer to “Lower An- chors and Tether for CHildren (LATCH)”. Rearward-facing child seats must never be used in the front seat of a vehicle with the front passenger air All children whose weight or height is above the bag.
Page 79 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 you make sure that you can install the child restraint in WARNING! the vehicle where you will use it, before you buy it. • Improper installation can lead to failure of an •...
Page 80 78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE retractor. For additional information on ALR, refer to retracts, you will hear a ratcheting sound. This indicates “Automatic Locking Mode”. The chart below defines the the safety belt is now in the Automatic Locking mode. seating positions with an Automatic Locking Retractor 2.
Page 81 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 • Make sure that the child is upright in the seat. around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, • The lap portion should be low on the hips and as snug try a different seating position.
Page 82 80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE webbing-mounted lower attachments. Child seats with fixed lower attachments must be installed in the out- board positions only. Regardless of the specific type of lower attachment, never install LATCH-compatible child seats such that two seats share a common lower anchor- age.
Page 83 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 provide add-on tether strap kits for some of their older restraint installation, instead of tucking the seat belt products. Tether anchorage kits are also available for behind the child restraint, route the seat belt through the most older vehicles.
Page 84 82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In general, you will first loosen the adjusters on the lower Not all child restraint systems will be installed as we and tether straps so that you can attach the hook or have described here.
Page 85: Engine Break-In Recommendations
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 Transporting Pets The engine oil installed in the engine at the factory is a Air Bags deploying in the front seat could harm your pet. high-quality energy conserving type lubricant. Oil An unrestrained pet will be thrown about and possibly changes should be consistent with anticipated climate injured, or injure a passenger during panic braking or in conditions under which vehicle operations will occur.
Page 86: Safety Tips
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SAFETY TIPS Exhaust Gas Transporting Passengers WARNING! NEVER TRANSPORT PASSENGERS IN THE CARGO AREA. Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. WARNING! Breathing it can make you unconscious and can •...
Page 87: Safety Checks You Should Make Inside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 Safety Checks You Should Make Inside The WARNING! (Continued) Vehicle • If it is necessary to sit in a parked vehicle with the Seat Belts engine running, adjust your heating or cooling Inspect the belt system periodically, checking for cuts, controls to force outside air into the vehicle.
Page 88 86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Defroster WARNING! (Continued) Check operation by selecting the defrost mode and place • Always make sure that floor mats are properly the blower control on high speed. You should be able to attached to the floor mat fasteners.
Page 89: Periodic Safety Checks You Should Make Outside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 lodged in the tread or sidewall. Inspect the tread for cuts WARNING! (Continued) and cracks. Inspect sidewalls for cuts, cracks and bulges. • Always make sure that objects cannot fall into the Check the wheel nuts for tightness.
Page 91: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors ......94 Uconnect™ Phone — If Equipped ... 98 Inside Day/Night Mirror .
Page 92 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Command — If Equipped ... 128 Head Restraints ..... 141 Voice Command System Operation .
Page 93 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 Instrument Panel Dimming ... . . 151 To Vary The Speed Setting ....159 Map/Reading Lights .
Page 94 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Sunroof — If Equipped ... . 169 Cupholders ......178 Opening Sunroof —...
Page 95 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 Rear Window Features ....188 Rear Window Defroster ....189 Rear Window Wiper/Washer .
Page 96: Mirrors
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of vehicle).
Page 97: Outside Mirror - Driver Side
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 to the left of the button will illuminate to indicate when CAUTION! the dimming feature is activated. The sensor to the right of the button does not illuminate. To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.
Page 98: Outside Mirror - Passenger Side
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirror — Passenger Side Power Mirrors Adjust the convex outside mirror so you can just see the The power mirror controls are located on the driver’s side of your vehicle in the part of the mirror closest to the door trim panel.
Page 99: Heated Mirrors - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 WARNING! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side mirror could cause you to collide with another vehicle or other object.
Page 100: Vanity Mirrors - If Equipped
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Vanity Mirrors — If Equipped Uconnect™ Phone — IF EQUIPPED To use the vanity mirror, rotate the sun visor down and Uconnect™ Phone is a voice-activated, hands-free, in- swing the mirror cover upward. vehicle communications system.
Page 101 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 • www.jeep.com/uconnect system. Only one linked (or paired) mobile phone can be used with the system at a time. The system is available in • or call 1–877–855–8400 English, Spanish, or French languages.
Page 102: Operation
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Command Button Operation Actual button location may vary with the ra- Voice commands can be used to operate the Uconnect™ dio. The individual buttons are described in the Phone and to navigate through the Uconnect™ Phone “Operation”...
Page 103 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 example, you can use the compound form voice Cancel Command command “Phonebook New Entry”, or you can break At any prompt, after the beep, you can say “Cancel” and the compound form command into two voice com- you will be returned to the main menu.
Page 104 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, after the beep, say “Pair a Device” phone to use if multiple mobile phones are in the and follow the audible prompts. vehicle at the same time. For example, if priority three and priority five phones are present in the vehicle, the •...
Page 105 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 • The Uconnect™ Phone will confirm the phone number • The Uconnect™ system will confirm the name and and then dial. The number will appear in the display then dial the corresponding phone number, which of certain radios.
Page 106 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, enter the number designation (e.g., Phonebook Download – Automatic Phonebook “Home”, “Work”, “Mobile”, or “Other”). This will Transfer From Mobile Phone allow you to store multiple numbers for each phone- If equipped and specifically supported by your phone, book entry, if desired.
Page 107 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 • Depending on the maximum number of entries down- Edit Uconnect™ Phonebook Entries loaded, there may be a short delay before the latest NOTE: downloaded names can be used. Until then, if avail- •...
Page 108 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After you enter the Phonebook Delete menu, you will After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in then be asked for the name of the entry that you wish the phonebook, call the number you just edited, or return to delete.
Page 109: Phone Call Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 • After the “Ready” prompt and the following beep, say Delete/Erase “All” Uconnect™ Phonebook Entries “Phonebook List Names”. • Press the button to begin. • The Uconnect™ Phone will play the names of all the •...
Page 110 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE mobile service plan. For example, if your mobile service mobile phone. Press the button to place the current plan provides three-way calling, this feature can be call on hold and answer the incoming call. accessed through the Uconnect™...
Page 111 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Place/Retrieve A Call From Hold Three-Way Calling To put a call on hold, press the button until you hear To initiate three-way calling, press the button while a single beep. This indicates that the call is on hold. To a call is in progress, and make a second phone call, as bring the call back from hold, press and hold the described under “Making a Second Call While Current...
Page 112: Uconnect™ Phone Features
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the “Ready” prompt and the following beep, say • After the ignition key is switched to OFF, a call can “Redial”. continue on the Uconnect™ Phone for a certain dura- tion, after which the call is automatically transferred •...
Page 113 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 • After the “Ready” prompt and the following beep, say After selecting one of the languages, all prompts and voice commands will be in that language. “Emergency” and the Uconnect™ Phone will instruct the paired mobile phone to call the emergency num- NOTE: After every Uconnect™...
Page 114 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Mexico City in Mexico). Please refer to the 24-Hour WARNING! “Towing Assistance” coverage details on the DVD in the Warranty Information Booklet and the 24-Hour To use your Uconnect™ Phone System in an emer- Towing Assistance references.
Page 115 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Working With Automated Systems is also to be used for navigating through an automated This method is used in instances where one generally has customer service center menu structure, and to leave a to press numbers on the mobile phone keypad while number on a pager.
Page 116 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Barge In — Overriding Prompts Phone And Network Status Indicators The “Voice Command” button can be used when you If available on the radio and/or on a premium display wish to skip part of a prompt and issue your voice such as the instrument panel cluster, and supported by command immediately.
Page 117: Advanced Phone Connectivity
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 NOTE: Certain brands of mobile phones do not send the Advanced Phone Connectivity dial ring to the Uconnect™ Phone to play it on the vehicle Transfer Call To And From Mobile Phone audio system, so you will not hear it. Under this situa- The Uconnect™...
Page 118 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the “Ready” prompt and the following beep, say List Paired Mobile Phone Names “Setup Select Phone” and follow the prompts. • Press the button to begin. • You can also press the button at any time while the •...
Page 119: Things You Should Know About Your Uconnect™ Phone
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 • You can also press the • Press the button at any time while the button and say the “Voice Training, list is being played, and then choose the phone you System Training, or Start Voice Training” command. wish to delete.
Page 120 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • fully closed windows, Voice Command • For best performance, adjust the rearview mirror to • dry weather condition. provide at least ⁄ in (1 cm) gap between the overhead • Even though the system is designed for users speaking console (if equipped) and the mirror.
Page 121 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 • Numbers must be spoken in single digits. “800” must • fully closed windows, be spoken “eight-zero-zero” not “eight hundred”. • dry weather conditions, and • You can say “O” (letter “O”) for “0” (zero). •...
Page 122 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Send Messages: Uconnect™ Phone can read or send new messages on You can send messages using Uconnect™ Phone. To send your phone. a new message: • Press the Read Messages: button. If you receive a new text message while your phone is •...
Page 123 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 List of Preset Messages: 11. See You in 15 minutes 1. Yes 12. I am on my way 2. No 13. I’ll be late 3. Where are you? 14. Are you there yet? 4.
Page 124 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn SMS Incoming Announcement ON/OFF Bluetooth Communication Link Turning the SMS Incoming Announcement OFF will stop Mobile phones have been found to lose connection to the the system from announcing the new incoming mes- Uconnect™...
Page 125 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123...
Page 126 124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 127 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125...
Page 128 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) zero call cancel confirmation prompts three continue four delete five dial download seven edit eight emergency nine English star (*) erase all plus (+) Espanol pound (#) Francais add location...
Page 129 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) language return to main menu return or main menu list names select phone select list phones send mobile set up phone settings or phone set up mute towing assistance mute off...
Page 130: General Information
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information NOTE: Take care to speak into the Voice Interface This device complies with Part 15 of the FCC rules and System as calmly and normally as possible. The ability of RSS 210 of Industry Canada. Operation is subject to the the Voice Interface System to recognize user voice com- following conditions: mands may be negatively affected by rapid speaking or a...
Page 131: Commands
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 If you ever wish to interrupt the system while it lists The system will best recognize your speech if the win- options, press the Voice Command button, listen dows are closed, and the heater/air conditioning fan is for the beep, and say your command.
Page 132 130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Use the ON/OFF VOLUME rotary knob to adjust the Radio AM volume to a comfortable level while the Voice Command To switch to the AM band, say “AM” or “Radio AM”. In system is speaking.
Page 133 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 • “Menu Radio” (to switch to the radio menu) Disc To switch to the disc mode, say “Disc”. In this mode, you • “Main Menu” (to switch to the main menu) may say the following commands: Satellite Radio •...
Page 134 132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • “Switch to system setup” − “Continue” (to continue recording) • “Change to setup” − “Delete” (to delete the recording) • “Play Memos” (to play previously recorded memos) • “Main menu setup” or —...
Page 135: Voice Training
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Voice Training SEATS For users experiencing difficulty with the system recog- Seats are a part of the Occupant Restraint System of the nizing their voice commands or numbers the Uconnect™ vehicle. Voice “Voice Training” feature may be used. WARNING! 1.
Page 136: Power Seats - If Equipped
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Seats — If Equipped WARNING! Some models may be equipped with a power driver’s • Adjusting a seat while driving may be dangerous. seat. The power seat switch is located on the outboard side of the seat near the floor.
Page 137: Heated Seats - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 Adjusting The Seat Forward Or Rearward Heated Seats — If Equipped The seat can be adjusted both forward and rearward. On some models, the front driver and passenger seats Push the seat switch forward or rearward, the seat will may be equipped with heaters in both the seat cushions move in the direction of the switch.
Page 138: Manual Front Seat Adjustment
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 45 minutes of continuous operation. If LOW-level heating WARNING! (Continued) is selected, the system automatically turns the heater and • Do not place anything on the seat or seatback that the indicator light OFF after a maximum of 45 minutes of insulates against heat, such as a blanket or cush- continuous operation.
Page 139 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked.
Page 140: Manual Seat Height Adjustment - If Equipped
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Seat Height Adjustment — If Equipped Manual Lumbar — If Equipped The driver’s seat height can be raised or lowered by using The lumbar adjustment handle is located on the outboard a lever, located on the outboard side of the seat. Pull side of the driver’s seatback.
Page 141: Driver's Seatback Recline
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Driver’s Seatback Recline WARNING! To adjust the seatback, lift the lever located on the outboard side of the seat, lean back to the desired angle Do not ride with the seatback reclined so that the and release the lever.
Page 142: Fold-Flat Front Passenger Seat
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fold-Flat Front Passenger Seat To fold the front passenger seat, lift the recliner handle to the full upward position and push the seatback forward until it rests on the seat cushion. Front Passenger Seat Folded Flat Fold-Flat Front Passenger Seat Lever...
Page 143: Head Restraints
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Head Restraints Active Head Restraints — Front Seats Head restraints are designed to reduce the risk of injury Active Head Restraints are passive, deployable compo- by restricting head movement in the event of a rear nents, and vehicles with this equipment cannot be readily impact.
Page 144 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To raise the head restraint, pull upward on the head For comfort the Active Head Restraints can be tilted restraint. To lower the head restraint, press the push forward and backward. To tilt the head restraint closer to button, located at the base of the head restraint, and push the back of your head, pull forward on the bottom of the downward on the head restraint.
Page 145 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 • In the event of deployment of an Active Head Re- straint, refer to “Occupant Restraints/Resetting Active Head Restraints (AHR)” in “Things To Know Before Starting Your Vehicle” for further information. WARNING! • Do not place items over the top of the Active Head Restraint, such as coats, seat covers or portable DVD players.
Page 146: Folding Rear Seat
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Rear Seat WARNING! (Continued) To provide additional storage area, each rear seatback can • Active Head Restraints may be deployed if they be folded forward. Pull the strap forward to move the are struck by an object such as a hand, foot or loose seatback forward and flat.
Page 147 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 To raise the seatback, pull the strap forward and lift the seatback into its upright position. WARNING! Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers.
Page 148: Reclining Rear Seat - If Equipped
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reclining Rear Seat — If Equipped For additional comfort, pull the strap forward just enough to release the seatback latch. Then push the seatback to a reclined position, approximately 35 degrees maximum, and release the strap. WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.
Page 149 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 CAUTION! To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approxi- mately 8 in (20 cm) and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged.
Page 150: Lights
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Headlights And Parking Lights Turn the end of the multifunction lever to the first detent Multifunction Lever to turn on the parking lights. The multifunction lever controls the operation of the headlights, parking lights, turn signals, headlight beam Turn the end of the lever to the second detent to turn on selection, instrument panel light dimming, interior lights, the headlights.
Page 151: Daytime Running Lights - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 Daytime Running Lights — If Equipped The high beam lights will come on as Daytime Running Lights (lower intensity), whenever the ignition is ON, the engine is running, the headlight switch is off, the parking brake is off, the turn signal is off, and the shift lever is in any position except PARK.
Page 152: Turn Signals
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn Signals NOTE: If either light remains on and does not flash, or Move the multifunction lever up or down and the arrows there is a very fast flash rate, check for a defective outside on each side of the instrument cluster flash to show light bulb.
Page 153: Instrument Panel Dimming
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 NOTE: If the multifunction lever is held in the flash-to- Rotate the center portion of the lever upward to the last pass position for more than 20 seconds, the high beams detent to turn on the interior lighting. will shut off.
Page 154: Map/Reading Lights
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Map/Reading Lights NOTE: The lights will remain on until the switch is These lights are mounted between above the rear view pressed a second time, so be sure they have been turned mirror. Each light is turned on by pressing the button. off before leaving the vehicle.
Page 155 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 CAUTION! • Turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper control is left in any position other than off. •...
Page 156: Windshield Wiper Operation
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Wiper Operation Rotate the end of the lever upward to the second detent past the intermittent settings for low-speed wiper opera- tion. Rotate the end of the lever upward to the third detent past the intermittent settings for high-speed wiper opera- tion.
Page 157: Windshield Washers
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 downward (counterclockwise) to increase the delay time. WARNING! The delay can be regulated from a maximum of approxi- mately 18 seconds between cycles, to a cycle every Sudden loss of visibility through the windshield second.
Page 158: Tilt Steering Column
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The mist feature does not activate the washer TILT STEERING COLUMN pump; therefore, no washer fluid will be sprayed on the This feature allows you to tilt the steering column windshield. The wash function must be used in order to upward or downward.
Page 159: Electronic Speed Control - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your ve- hicle.
Page 160: To Activate
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Electronic Speed Control buttons are located on the down if multiple Speed Control functions are operated at right side of the steering wheel. the same time. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed.
Page 161: To Set A Desired Speed
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 To Set A Desired Speed To Resume Speed Turn the Electronic Speed Control ON. When the vehicle To resume a previously set speed, push the RES (+) has reached the desired speed, press the SET (-) button button and release.
Page 162: To Accelerate For Passing
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE decrease until the button is released. Release the button On steep hills, a greater speed loss or gain may occur so when the desired speed is reached, and the new set speed it may be preferable to drive without Electronic Speed will be established.
Page 163 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 The HomeLink buttons, located on either the overhead console, headliner or sunvisor, designate the three differ- ent HomeLink channels. The HomeLink indicator is located above the center button. HomeLink Buttons/Sunvisor/Headliner NOTE: HomeLink is disabled when the Vehicle Secu- rity Alarm is active.
Page 164: Before You Begin Programming Homelink
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • If you have any problems, or require assistance, please Before You Begin Programming HomeLink Be sure that your vehicle is parked outside of the garage call toll-free 1–800–355–3515 or, on the Internet at before you begin programming.
Page 165 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 3. Simultaneously press and hold both the Homelink button you want to program and the hand-held transmit- ter button. 4. Continue to hold both buttons and observe the indi- cator light. The Homelink indicator will flash slowly and then rapidly after Homelink has received the fre- quency signal from the hand-held transmitter.
Page 166: Programming A Non-Rolling Code
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: You have 30 seconds in which to initiate the next 2. Press and hold the desired HomeLink button until step after the LEARN button has been pressed. the indicator light begins to flash after 20 seconds. Do not release the button.
Page 167: Canadian/Gate Operator Programming
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 4. Continue to hold both buttons and observe the indi- Reprogramming A Single HomeLink Button cator light. The Homelink indicator will flash slowly To reprogram a channel that has been previously trained, and then rapidly after Homelink has received the fre- follow these steps: quency signal from the hand-held transmitter.
Page 168 166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE to pick up the signal during programming. Similar to this 4. Watch for the HomeLink indicator to change flash Canadian law, some U.S. gate operators are designed to rates. When it changes, it is programmed. It may take up time-out in the same manner.
Page 169: Using Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 Reprogramming A Single HomeLink Button Security To reprogram a channel that has been previously trained, It is advised to erase all channels before you sell or turn follow these steps: in your vehicle. 1.
Page 170: Troubleshooting Tips
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Troubleshooting Tips WARNING! If you are having trouble programming HomeLink , here • Your motorized door or gate will open and close are some of the most common solutions: while you are programming the universal trans- •...
Page 171: General Information
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 General Information POWER SUNROOF — IF EQUIPPED This device complies with FCC rules Part 15 and Industry The power sunroof switch is located in the reading light. Canada RSS-210. Operation is subject to the following two conditions: 1.
Page 172: Opening Sunroof - Express
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof — Express WARNING! Press the switch rearward and release it within one-half • Never leave children in a vehicle with the key in second and the sunroof will open automatically from any position.
Page 173: Closing Sunroof - Manual Mode
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 position. The sunroof will close fully and stop automati- NOTE: Pinch protection is disabled while the switch is cally. This is called “Express Close”. During Express pressed. Close operation, any movement of the switch will stop Venting Sunroof —...
Page 174: Wind Buffeting
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Wind Buffeting Ignition Off Operation Wind buffeting can be described as the perception of For vehicles not equipped with the Electronic Vehicle pressure on the ears or a helicopter-type sound in the Information Center (EVIC), the power sunroof switch ears.
Page 175: Electrical Power Outlets
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 ELECTRICAL POWER OUTLETS Power is available when the ignition switch is in the ON There is a standard 12 Volt (13 Amp) power outlet located or ACC position. Insert the cigar lighter or accessory plug in the instrument panel for added convenience.
Page 176 174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced. •...
Page 177 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 WARNING! CAUTION! • Many accessories that can be plugged in draw To avoid serious injury or death: • Only devices designed for use in this type of power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
Page 178: Power Inverter - If Equipped
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER INVERTER — IF EQUIPPED The power inverter is designed with built-in overload A 115 Volt (150 Watt) AC power inverter is located on the protection. If the power rating of 150 Watts is exceeded, front of the center console for added convenience.
Page 179 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 WARNING! To avoid serious injury or death: • Do not use a three-prong adaptor. • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use. •...
Page 180: Cupholders
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUPHOLDERS CAUTION! Your vehicle is equipped with four cupholders. There are • Many accessories that can be plugged in draw two illuminated cupholders located in the front. power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
Page 181: Storage
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 Rear Cupholders Storage Compartments STORAGE 1 — Upper Storage Bin 2 — Lower Glove Compartment Glove Compartment And Storage Bin Located on the passenger side of the instrument panel are an upper storage bin and a lower glove compartment.
Page 182: Door Storage
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To open the lower glove compartment, pull outward on Door Storage the release handle. The interior door panels are equipped with lower storage areas. Glove Compartment Front Door Storage...
Page 183: Console Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 CONSOLE FEATURES The floor console contains both an upper and lower storage compartment. To open the upper storage compartment, push inward on the upper handle to unlatch the upper lid and lift the lid open.
Page 184: Cargo Area Features
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To open the lower storage compartment, lift upward on WARNING! the lower handle to unlatch the lower storage compart- ment and lift the lid open. Do not operate this vehicle with a console compart- ment lid in the open position.
Page 185: Cargo Cover
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 Press in on the flashlight to release it. Three-Press Switch Cargo Cover Press And Release The cargo area trim panels include two notches for To operate the flashlight, press the switch once for high, mounting the available tonneau cover that accommo- twice for low, and a third time to return to off.
Page 186 184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To install the Cargo Cover, insert either end of the cover Using the handle, pull the cover toward you and guide into one of the two notches located in the rear trim the rear cover posts into the guides located on both sides panels.
Page 187: Removable Load Floor
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 Removable Load Floor WARNING! The cargo area load floor is removable and can be washed with mild soap and water. In a collision a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle.
Page 188: Cargo Tie-Down Loops
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Tie-Down Loops WARNING! There are four D-rings installed in the cargo area for • Cargo tie-down loops are not safe anchors for a securing cargo. child seat tether strap. In a sudden stop or collision a loop could pull loose and allow the child seat to come loose.
Page 189: Fold Down Speakers - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 Fold Down Speakers — If Equipped WARNING! (Continued) When the liftgate is open, the speakers can swing down • Place as much cargo as possible in front of the rear off the trim panel to face rearward, for tailgating and axle.
Page 190: Rear Window Features
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES Rotate the center portion of the lever upward to the first detent position for rear wiper operation. Rear Window Wiper/Washer The rear wiper/washer is controlled by a rotary switch NOTE: The rear wiper operates in an intermittent mode located on the center portion of the control lever.
Page 191: Rear Window Defroster
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 Rear Window Defroster CAUTION! The rear window defroster button is located on the bottom right-side of the blower control knob. Failure to follow these cautions can cause damage to Press this button to turn on the rear window defroster the heating elements: and the heated outside mirrors (if equipped).
Page 192: Roof Luggage Rack - If Equipped
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ROOF LUGGAGE RACK — IF EQUIPPED The roof rack does not increase the total load carrying The side rails and crossbars are designed to carry weight capacity of the vehicle. Be sure the total load of cargo on vehicles equipped with a luggage rack.
Page 193 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 CAUTION! (Continued) WARNING! • To avoid damage to the roof rack and vehicle, do Cargo must be securely tied down before driving not exceed the maximum roof rack load capacity of your vehicle. Improperly secured loads can fly off the 150 lbs (68 kg).
Page 195: Understanding Your Instrument Panel
....197 Compass/Temperature/Audio ... 218 Instrument Cluster Descriptions ... 198 Average Fuel Economy .
Page 196 194 UNDERSTANDING YOUR INSTRUMENT PANEL Media Center 230 (REQ) — AM/FM Stereo Media Center 730N/430/430N (RHR/RER/ Radio And 6–Disc CD/DVD Changer RBZ/RHB) CD/DVD/HDD/NAV — If (MP3/WMA AUX Jack) ....224 Equipped .
Page 197 UNDERSTANDING YOUR INSTRUMENT PANEL 195 Operation Instructions — CD Mode For CD List Or Browse Mode ....272 And MP3 Audio Play ....258 Bluetooth Streaming Audio (BTSA) .
Page 198: Instrument Panel Features
196 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 — Air Outlet 5 — Storage Bin 9 — Heated Seat Switch – If Equipped 2 — Demisters 6 — Glove Compartment 10 — Hazard Warning Flasher 3 — Instrument Cluster 7 —...
Page 199: Instrument Cluster
UNDERSTANDING YOUR INSTRUMENT PANEL 197 INSTRUMENT CLUSTER...
Page 200: Instrument Cluster Descriptions
198 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS If jump starting is required, refer to “Jump Starting Procedures” in “What To Do In Emergencies”. 1. Fuel Gauge / Fuel Door Reminder When the ignition switch is in the ON/RUN 3. Electronic Throttle Control (ETC) Light position, the pointer will show the level of fuel This light informs you of a problem with the remaining in the fuel tank.
Page 201 UNDERSTANDING YOUR INSTRUMENT PANEL 199 on briefly as a bulb check. If the light does not come on 6. Speedometer during starting, have the system checked by an autho- The Speedometer shows the vehicle speed in miles per rized dealer. hour and/or kilometers per hour (mph/kph).
Page 202 200 UNDERSTANDING YOUR INSTRUMENT PANEL alert you to turn the signals off. If either indicator flashes If the ABS light is on, the brake system should be serviced at a rapid rate, check for a defective outside light bulb. as soon as possible to restore the benefits of Anti-Lock brakes.
Page 203 UNDERSTANDING YOUR INSTRUMENT PANEL 201 12. Tachometer normal, turn the engine off immediately and call for The white area of the scale shows the permissible engine service. Refer to “If Your Engine Overheats” in “What To revolutions-per-minute (RPM x 1000) for each gear range. Do In Emergencies”...
Page 204 202 UNDERSTANDING YOUR INSTRUMENT PANEL booster, the ABS pump will run when applying the brake WARNING! and a brake pedal pulsation may be felt during each stop. Driving a vehicle with the red brake light on is The dual brake system provides a reserve braking capac- dangerous.
Page 205 UNDERSTANDING YOUR INSTRUMENT PANEL 203 The light also will turn on when the parking brake is WARNING! applied with the ignition switch in the ON/RUN posi- tion. If the Transmission Temperature Warning Light is illuminated and you continue operating the vehicle, NOTE: This light shows only that the parking brake is in some circumstances you could cause the fluid to applied.
Page 206 204 UNDERSTANDING YOUR INSTRUMENT PANEL The gauge pointer will likely indicate a higher tempera- WARNING! ture when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to A hot engine cooling system is dangerous. You or exceed the upper limits of the normal operating range.
Page 207 UNDERSTANDING YOUR INSTRUMENT PANEL 205 20. Shift Lever Indicator placard or tire inflation pressure label. (If your vehicle The Shift Lever Indicator is self-contained within the has tires of a different size than the size indicated on the instrument cluster. It displays the gear position of the vehicle placard or tire inflation pressure label, you should automatic transmission.
Page 208 206 UNDERSTANDING YOUR INSTRUMENT PANEL Please note that the TPMS is not a substitute for proper TPMS malfunction telltale after replacing one or more tire maintenance, and it is the driver’s responsibility to tires or wheels on your vehicle, to ensure that the maintain correct tire pressure, even if under-inflation has replacement or alternate tires and wheels allow the TPMS not reached the level to trigger illumination of the TPMS...
Page 209 UNDERSTANDING YOUR INSTRUMENT PANEL 207 23. Odometer Display / Trip Odometer Display Area Vehicle Odometer Messages This display indicates the total distance the vehicle has When the appropriate conditions exist, the following been driven. odometer messages will display: NOTE: U.S. Federal regulations require that upon trans- door .
Page 210 208 UNDERSTANDING YOUR INSTRUMENT PANEL gASCAP Refer to “Engine Oil Overheating” under in “What To Do If the vehicle diagnostic system determines that the fuel In Emergencies”. filler cap is loose, improperly installed, or damaged, a CHANgE OIL Message “gASCAP” message will display in the odometer display Your vehicle is equipped with an engine oil change area.
Page 211 UNDERSTANDING YOUR INSTRUMENT PANEL 209 2. Fully depress the accelerator pedal, slowly, three Certain conditions, such as a loose or missing gas cap, times within 10 seconds. poor fuel quality, etc., may illuminate the light after engine start. The vehicle should be serviced if the light 3.
Page 212 210 UNDERSTANDING YOUR INSTRUMENT PANEL 27. Electronic Stability Control (ESC) Activation/ WARNING! Malfunction Indicator Light — If Equipped The “ESC Activation/Malfunction Indicator A malfunctioning catalytic converter, as referenced Light” in the instrument cluster will come on above, can reach higher temperatures than in normal when the ignition switch is turned to the operating conditions.
Page 213: Mini-Trip Computer - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 211 • Each time the ignition is turned to ON/RUN, the ESC 29. Electronic Vehicle Information Center (EVIC) system will be ON, even if it was turned off previously. Display — If Equipped When the appropriate conditions exist, this display •...
Page 214: Control Buttons
212 UNDERSTANDING YOUR INSTRUMENT PANEL be driven several minutes before the updated tempera- STEP Button ture is displayed. Engine temperature can also affect the Press the STEP button located on the steering wheel to displayed temperature; therefore, temperature readings scroll through sub menus (i.e., Temperature, Trip Func- are not updated when the vehicle is not moving.
Page 215: Electronic Vehicle Information Center (Evic) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 213 Trip A Shows the total distance traveled for Trip A since the last reset. Trip B Shows the total distance traveled for Trip B since the last reset. ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) — IF EQUIPPED The Electronic Vehicle Information Center (EVIC) fea- tures a driver-interactive display that is located in the instrument cluster.
Page 216 • System Status wheel: • Vehicle Information Warning Message Displays • Personal Settings (Customer-Programmable Features) • Compass Heading • Outside Temperature Display • Trip Computer Functions • Uconnect™ phone Displays (if equipped) • Audio Mode Display •...
Page 217 Press and release the COMPASS button to • Turn Signal On (with a continuous warning chime display one of eight compass readings and the outside temperature or to exit sub-menus. after 1 mile (1.6 km) of distance travelled) •...
Page 218: Engine Oil Change Indicator System - If Equipped
216 UNDERSTANDING YOUR INSTRUMENT PANEL • Personal Settings Not Avail. — Vehicle not in PARK • Remote Start Aborted — Fuel Low (automatic transmission) or vehicle is in motion • Remote Start Aborted — System Fault (manual transmission). • Key In Ignition •...
Page 219: Evic Functions
Unless reset, this message will continue to display each EVIC Functions time you turn the ignition switch to the ON/RUN • Compass/Temperature/Audio position. To turn off the message temporarily, press and • Average Fuel Economy release the Trip Odometer button on the instrument cluster.
Page 220: Compass/Temperature/Audio
Compass/Temperature/Audio and average fuel economy, according to the current fuel Press and release the COMPASS button to display one of tank level. This is not resettable. eight compass headings to indicate the direction the...
Page 221: Tire Pressure Monitor (Tpm)
UNDERSTANDING YOUR INSTRUMENT PANEL 219 Tire Pressure Monitor (TPM) Personal Settings Refer to “Starting And Operating”, “Tire Pressure Moni- (Customer-Programmable Features) toring System (TPMS)” for system operation. This allows the driver to set and recall features when the transmission is in PARK (automatic transmission) or the Elapsed Time vehicle is stopped (manual transmission).
Page 222 220 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Uconnect™ language will not change using the RKE Unlock Driver’s Door 1st EVIC. Please refer to “Language Selection” in Uconnect™ When Driver’s Door 1st is selected only the driver’s door phone — If Equipped for details. will unlock on the first press of the Remote Keyless Entry (RKE) transmitter UNLOCK button and require a second Auto Lock Doors...
Page 223 UNDERSTANDING YOUR INSTRUMENT PANEL 221 Sound Horn with Lock either front vehicle door will cancel this feature. Press When ON is selected, a short horn sound will occur when and hold the SELECT button when in this display until the RKE transmitter LOCK button is pressed. This feature “OFF”, “45 sec.”, “5 min.”, or “10 min.”...
Page 224 This compass is self-calibrating, which eliminates the to enter the EVIC Programming Menus. need to set the compass manually. When the vehicle is 2. Press the MENU button until the Personal Settings new, the compass may appear erratic and the EVIC will (Customer-Programmable Features) menu displays in the display “CAL”...
Page 225 Once properly Compass Variance Map set, the compass will automatically compensate for the 1. Turn the ignition switch ON. differences and provide the most accurate compass head- ing. 2. Press and hold the COMPASS button for approxi- mately two seconds.
Page 226: Media Center 230 (Req) - Am/Fm Stereo Radio And 6-Disc Cd/Dvd Changer (Mp3/Wma Aux Jack)
EVIC. 4. Press and release the SELECT button until the proper variance zone is selected according to the map. 5. Press and release the COMPASS button to exit. MEDIA CENTER 230 (REQ) — AM/FM STEREO RADIO AND 6–DISC CD/DVD CHANGER...
Page 227 UNDERSTANDING YOUR INSTRUMENT PANEL 225 Power Switch/Volume Control (Rotary) SCAN Button Push the ON/VOLUME control knob to turn on the Pressing the SCAN button causes the tuner to search for radio. Press the ON/VOLUME control knob a second the next listenable station in AM, FM or Satellite (if time to turn off the radio.
Page 228 226 UNDERSTANDING YOUR INSTRUMENT PANEL Phone Button Uconnect™ Phone — If Equipped 3. After adjusting the hours, press the right side TUNE/ Press this button to operate the Uconnect™ Phone feature SCROLL control knob to set the minutes. The minutes (if equipped).
Page 229 UNDERSTANDING YOUR INSTRUMENT PANEL 227 RW/FF Push the rotary TUNE/SCROLL control knob a third Pressing the RW (Rewind) or FF (Fast Forward) buttons time and TREBLE will display. Turn the TUNE/SCROLL causes the tuner to search for the next frequency in the control knob to the right or left to increase or decrease the direction of the arrows.
Page 230 228 UNDERSTANDING YOUR INSTRUMENT PANEL MUSIC TYPE Button Program Type 16-Digit Character Display Pressing this button once will turn on the Music Type Information Inform mode for five seconds. Pressing the MUSIC TYPE button Jazz Jazz or turning the TUNE/SCROLL control knob within five News News seconds will allow the program format type to be se-...
Page 231 UNDERSTANDING YOUR INSTRUMENT PANEL 229 • DVD Enter - When the disc is in DVD Menu mode, Program Type 16-Digit Character Display selecting DVD Enter will allow you to play the current Top 40 Top 40 highlighted selection. Use the remote control to scroll Weather Weather up and down the menu (if equipped).
Page 232 230 UNDERSTANDING YOUR INSTRUMENT PANEL • Angle – Repeatedly pressing SELECT will change • Set Home Clock - Pressing the SELECT button allows the viewing angle if supported by the DVD disc (if you to set the clock. Turn the TUNE/SCROLL control equipped).
Page 233 UNDERSTANDING YOUR INSTRUMENT PANEL 231 Audio Language — If Equipped Audio DRC — If Equipped Selecting this item allows you to choose a default audio Selecting this item allows you to limit maximum audio language (effective only if the language is supported by dynamic range.
Page 234 232 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The user will have to set these defaults before You may add a second station to each pushbutton by loading a disc. If changes are made to these settings after repeating the above procedure with this exception: Press a disc is loaded, changes will not be effective.
Page 235: Operation Instructions - (Disc Mode For Cd And Mp3/Wma Audio Play, Dvd-Video)
UNDERSTANDING YOUR INSTRUMENT PANEL 233 Operation Instructions - (DISC MODE for CD and NOTE: The ignition switch must be in the ON or ACC MP3/WMA Audio Play, DVD-VIDEO) position to operate the radio. The radio DVD player and many DVD discs are coded by LOAD Button —...
Page 236 234 UNDERSTANDING YOUR INSTRUMENT PANEL Eject Button — Ejecting Compact Disc(s) SCAN Button (CD MODE) Press the EJECT button and the pushbutton Press the SCAN button to scan through each track on the with the corresponding number (1-6) where the CD currently playing.
Page 237: Notes On Playing Mp3/Wma Files
UNDERSTANDING YOUR INSTRUMENT PANEL 235 Notes On Playing MP3/WMA Files The radio uses the following limits for file systems: The radio can play MP3/WMA files; however, acceptable • Maximum number of directory levels: 8 MP3/WMA file recording media and formats are limited. •...
Page 238 236 UNDERSTANDING YOUR INSTRUMENT PANEL If a disc contains multi-formats, such as CD audio and MPEG Sampling Fre- Bit Rate (kbps) MP3/WMA tracks, the radio will only play the MP3/ Specification quency (kHz) WMA tracks on that disc. 320, 256, 224, MPEG-1 Audio 192, 160, 128, Supported MP3/WMA File Formats...
Page 239: List Button (Disc Mode For Mp3/Wma Play)
UNDERSTANDING YOUR INSTRUMENT PANEL 237 Playback of MP3/WMA Files LIST Button (DISC Mode for MP3/WMA Play) When a medium containing MP3/WMA data is loaded, Pressing the LIST button will bring up a list of all folders the radio checks all files on the medium. If the medium on the disc.
Page 240 238 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the INFO button again for three seconds SCAN Button (Auxiliary Mode) to return to elapsed time display. No function. Operation Instructions - Auxiliary Mode EJECT Button (Auxiliary Mode) The auxiliary (AUX) jack is an audio input jack which No function.
Page 241: Uconnect™ Multimedia (Satellite Radio) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 239 Operating Instructions — Voice Command System Macrovision (If Equipped) This product incorporates copyright protection technol- For the radio, Refer to “Voice Command” in the ogy that is protected by U.S. patents and other intellec- Uconnect™ User Manual located on the DVD for further tual property rights.
Page 242 240 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Sirius service is not available in Hawaii and has 2. Your Vehicle Identification Number. limited coverage in Alaska. To access the ESN/SID, refer to the following steps: System Activation ESN/SID Access Sirius Satellite Radio service is pre-activated, and you With the ignition switch in the ON/RUN or ACC posi- may begin listening immediately to the one year of audio tion and the radio on, press the SETUP button and scroll...
Page 243 UNDERSTANDING YOUR INSTRUMENT PANEL 241 placed within the line of sight of the antenna will cause Operating Instructions - Uconnect™ Multimedia decreased performance. Larger luggage items such as (Satellite) Mode bikes should be placed as far rearward as possible, within NOTE: The ignition switch must be in the ON/RUN or the loading design of the rack.
Page 244 242 UNDERSTANDING YOUR INSTRUMENT PANEL INFO Button or turning the TUNE/SCROLL control knob within five Pressing the INFO button will cycle the display informa- seconds will allow the program format type to be selected. tion between Artist, Song Title, and Composer (if avail- Toggle the MUSIC TYPE button again to select the music able).
Page 245: Media Center 730N/430/430N
UNDERSTANDING YOUR INSTRUMENT PANEL 243 SET Button – To Set the Pushbutton Memory Buttons 1 - 6 When you are receiving a channel that you wish to These buttons tune the radio to the channels that you commit to pushbutton memory, press the SET button. commit to pushbutton memory (12 Satellite stations).
Page 246: Media Center 130 (Sales Code Res)
244 UNDERSTANDING YOUR INSTRUMENT PANEL MEDIA CENTER 130 (SALES CODE RES) Operating Instructions — Radio Mode NOTE: The radio sales code is located on the lower right NOTE: The ignition switch must be in the ON or ACC side of the radio faceplate. position to operate the radio.
Page 247 UNDERSTANDING YOUR INSTRUMENT PANEL 245 SEEK Buttons 4. Adjust the minutes using the right side TUNE/ Press and release the SEEK buttons to search for the next SCROLL control knob. Press the TUNE/SCROLL control listenable station in AM/FM mode. Press the right switch knob to save time change.
Page 248 246 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob a second AM/FM Button time and MID will display. Turn the TUNE/SCROLL Press the buttons to select either AM or FM mode. control knob to the right or left to increase or decrease the SET/RND Button —...
Page 249: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
UNDERSTANDING YOUR INSTRUMENT PANEL 247 • This radio is capable of playing compact discs (CD), and 12 FM stations to be stored into pushbutton memory. The stations stored in SET 2 memory can be selected by recordable compact discs (CD-R), rewritable compact pressing the pushbutton twice.
Page 250 248 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Ejecting with the ignition OFF is not allowed on CAUTION! convertible or soft-top models (if equipped). • This CD player will accept 4-3/4 in (12 cm) discs SEEK Button only. The use of other sized discs may damage the Press the right SEEK button for the next selection on the CD player mechanism.
Page 251: Notes On Playing Mp3 Files
UNDERSTANDING YOUR INSTRUMENT PANEL 249 AM/FM Button Supported Media (Disc Types) Press the button to select either AM or FM mode. The MP3 file recording media supported by the radio are CDDA, CD-R, CD-RW, MP3, and CDDA+MP3. SET/RND Button (Random Play Button) Press this button while the CD is playing to activate Supported Medium Formats (File Systems) Random Play.
Page 252 250 UNDERSTANDING YOUR INSTRUMENT PANEL a number instead. With a maximum number of files, Supported MP3 File Formats exceeding 20 folders will result in this display. With The radio will recognize only files with the *.MP3 exten- 200 files, exceeding 50 folders will result in this sion as MP3 files.
Page 253 UNDERSTANDING YOUR INSTRUMENT PANEL 251 Playback of MP3 Files MPEG Sampling Fre- Bit Rate (kbps) When a medium containing MP3 data is loaded, the Specification quency (kHz) radio checks all files on the medium. If the medium 320, 256, 224, contains a lot of folders or files, the radio will take more MPEG-1 Audio 192, 160, 128,...
Page 254: Operation Instructions - Auxiliary Mode
252 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - Auxiliary Mode MEDIA CENTER 130 WITH SATELLITE RADIO The auxiliary (AUX) jack is an audio input jack, which (SALES CODE RES+RSC) allows the user to plug in a portable device, such as an NOTE: The radio sales code is located on the lower right MP3 player, or cassette player, and utilize the vehicle’s side of the radio faceplate.
Page 255: Operating Instructions - Radio Mode
UNDERSTANDING YOUR INSTRUMENT PANEL 253 Operating Instructions — Radio Mode to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make NOTE: The ignition switch must be in the ON or ACC another selection.
Page 256 254 UNDERSTANDING YOUR INSTRUMENT PANEL Phone Button Uconnect™ Phone — If Equipped 3. After adjusting the hours, press the right side TUNE/ Press this button to operate the Uconnect™ Phone feature SCROLL control knob to set the minutes. The minutes (if equipped).
Page 257 UNDERSTANDING YOUR INSTRUMENT PANEL 255 INFO Button Push the rotary TUNE/SCROLL control knob a second Press the INFO button for an RDS station (one with call time and MID will display. Turn the TUNE/SCROLL letters displayed). The radio will return a Radio Text control knob to the right or left to increase or decrease the message broadcast from an FM station (FM mode only).
Page 258 256 UNDERSTANDING YOUR INSTRUMENT PANEL MUSIC TYPE Button Program Type 16-Digit Character Display Pressing this button once will turn on the Music Type Information Inform mode for five seconds. Pressing the MUSIC TYPE button Jazz Jazz or turning the TUNE/SCROLL control knob within five News News seconds will allow the program format type to be se-...
Page 259 UNDERSTANDING YOUR INSTRUMENT PANEL 257 hours, press the TUNE/SCROLL control knob to set Program Type 16-Digit Character Display the minutes. The minutes will begin to blink. Adjust Top 40 Top 40 the minutes using the right side TUNE/SCROLL Weather Weather control knob.
Page 260: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
258 UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each pushbutton by Operation Instructions — CD MODE for CD and repeating the above procedure with this exception: Press MP3 Audio Play the SET/RND button twice and SET 2 will show in the NOTE: display window.
Page 261 UNDERSTANDING YOUR INSTRUMENT PANEL 259 If you insert a disc with the ignition ON and the radio If you have ejected a disc and have not removed it within ON, the unit will switch from radio to CD mode and 10 seconds, it will be reloaded.
Page 262: Notes On Playing Mp3 Files
260 UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF Notes On Playing MP3 Files Press and hold FF (Fast Forward) and the CD player will The radio can play MP3 files; however, acceptable MP3 begin to fast forward until FF is released or RW or file recording media and formats are limited.
Page 263 UNDERSTANDING YOUR INSTRUMENT PANEL 261 • Maximum number of files: 255 Discs created with an option such as keep disc open after writing are most likely multisession discs. The use of • Maximum number of folders. (The radio display of file multisession for CD audio or MP3 playback may result in names and folder names is limited.
Page 264 262 UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 Files MPEG Sampling Fre- Bit Rate (kbps) When a medium containing MP3 data is loaded, the Specification quency (kHz) radio checks all files on the medium. If the medium 320, 256, 224, contains a lot of folders or files, the radio will take more MPEG-1 Audio 192, 160, 128,...
Page 265: List Button (Cd Mode For Mp3 Play)
UNDERSTANDING YOUR INSTRUMENT PANEL 263 LIST Button (CD Mode for MP3 Play) Press and hold the INFO button again for three seconds Pressing the LIST button will bring up a list of all folders to return to elapsed time display. on the disc.
Page 266: Uconnect™ Multimedia (Satellite Radio) - If Equipped
264 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (Auxiliary Mode) radio system in your vehicle. Sirius will supply a wel- Press this button to change the display to time of day. The come kit that contains general information, including time of day will display for five seconds (when the how to setup your on-line listening account.
Page 267 UNDERSTANDING YOUR INSTRUMENT PANEL 265 using the TUNE/SCROLL control knob until Sirius ID is Reception Quality selected. Press the TUNE/SCROLL control knob and the Satellite reception may be interrupted due to one of the Sirius ID number will display. The Sirius ID number following reasons: display will time out in two minutes.
Page 268 266 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons additional three seconds will make the radio display the Press and release the SEEK buttons to search for the next Song Title all of the time (press and hold again to return channel in Satellite mode. Press the right switch to seek to normal display).
Page 269 UNDERSTANDING YOUR INSTRUMENT PANEL 267 Toggle the MUSIC TYPE button again to select the music SET Button – To Set the Pushbutton Memory type. When you are receiving a channel that you wish to commit to pushbutton memory, press the SET button. By pressing the SEEK button when the Music Type The symbol SET 1 will now show in the display window.
Page 270: Ipod /Usb/Mp3 Control - If Equipped
268 UNDERSTANDING YOUR INSTRUMENT PANEL Every time a preset button is used, a corresponding This feature allows an iPod or external USB device to be button number will display. plugged into the USB port, located in the center console or glove compartment. Buttons 1 - 6 These buttons tune the radio to the channels that you iPod control supports Mini, 4G, Photo, Nano, 5G iPod...
Page 271: Connecting The Ipod Or External Usb Device
UNDERSTANDING YOUR INSTRUMENT PANEL 269 Connecting The iPod Or External USB Device Once the audio device is connected and synchronized to Use the connection cable to connect an iPod or external the vehicle’s iPod /USB/MP3 control system (iPod or USB device to the vehicle’s USB/AUX connector port external USB device may take a few minutes to connect), which is located in the center console or glove compart- the audio device starts charging and is ready for use by...
Page 272: Controlling The Ipod Or External Usb Device Using Radio Buttons
270 UNDERSTANDING YOUR INSTRUMENT PANEL • The audio device can be controlled using the radio Play Mode buttons to Play, Browse, and List the iPod contents. When switched to iPod /USB/MP3 control mode, the iPod or external USB device automatically starts Play •...
Page 273 UNDERSTANDING YOUR INSTRUMENT PANEL 271 • Jump forward in the current track by pressing and • Pressing the REPEAT button will change the audio holding the FF >> button. device mode to repeat the current playing track or press the VR button and say Repeat ON or Repeat •...
Page 274: List Or Browse Mode
272 UNDERSTANDING YOUR INSTRUMENT PANEL • During all List modes, the iPod displays all lists in List Or Browse Mode During Play mode, pressing any of the buttons described “wrap-around” mode. So if the track is at the below, will bring up List mode. List mode enables bottom of the list, just turn the wheel backward scrolling through the list of menus and tracks on the (counterclockwise) to get to the track faster.
Page 275 UNDERSTANDING YOUR INSTRUMENT PANEL 273 • Pressing a PRESET button will display the current CAUTION! list on the top line and the first item in that list on • Leaving the iPod or external USB device (or any the second line. supported device) anywhere in the vehicle in •...
Page 276: Bluetooth Streaming Audio (Btsa)
274 UNDERSTANDING YOUR INSTRUMENT PANEL Bluetooth Streaming Audio (BTSA) 2. After the Ready prompt and the following beep, say Music can be streamed from your cellular phone to the Setup , then Select Audio Devices . Uconnect™ phone system. 3. Say the name of the audio device or ask the Controlling BTSA Using Radio Buttons Uconnect™...
Page 277: Steering Wheel Audio Controls
UNDERSTANDING YOUR INSTRUMENT PANEL 275 STEERING WHEEL AUDIO CONTROLS The right-hand control is a rocker-type switch with a The remote sound system controls are located on the rear pushbutton in the center and controls the volume and surface of the steering wheel. Reach behind the wheel to mode of the sound system.
Page 278: Cd Player
276 UNDERSTANDING YOUR INSTRUMENT PANEL The button located in the center of the left-hand control CD/DVD DISC MAINTENANCE will tune to the next preset station that you have pro- To keep a CD/DVD in good condition, take the following grammed in the radio preset pushbutton. precautions: CD Player 1.
Page 279: Radio Operation And Mobile Phones
UNDERSTANDING YOUR INSTRUMENT PANEL 277 NOTE: If you experience difficulty in playing a particu- Manual Heating And Air Conditioning lar disc, it may be damaged (i.e., scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known good disc before considering disc player service.
Page 280 278 UNDERSTANDING YOUR INSTRUMENT PANEL Blower Control Temperature Control Rotate this control to regulate the Rotate this control to regulate the tem- amount of air forced through the ven- perature of the air inside the passenger tilation system in any mode. The compartment.
Page 281 UNDERSTANDING YOUR INSTRUMENT PANEL 279 Mode Control (Air Direction) Bi-Level Rotate this control to choose from sev- Air is directed through the panel and floor outlets. eral patterns of air distribution. You can select either a primary mode as NOTE: For all settings, except full cold or full hot, there identified by the symbols on the con- is a difference in temperature between the upper and trol, or a blend of two of these modes.
Page 282 280 UNDERSTANDING YOUR INSTRUMENT PANEL Defrost Recirculation Control Air is directed through the windshield and side Pressing the Recirculation Control button will window demist outlets. Use this mode with maxi- put the system in recirculation mode. This can mum blower and temperature settings for best wind- be used when outside conditions such as shield and side window defrosting.
Page 283 UNDERSTANDING YOUR INSTRUMENT PANEL 281 • The A/C can be deselected manually without disturb- NOTE: The air conditioning compressor will not engage ing the mode control selection. until the engine has been running for about 10 seconds. • When the ignition switch is turned to the LOCK •...
Page 284: Automatic Temperature Control (Atc) - If
282 UNDERSTANDING YOUR INSTRUMENT PANEL Automatic Temperature Control (ATC) — If Automatic Operation Equipped Operation of the system is quite simple. The Automatic Temperature Control system automati- 1. Turn the Mode Control knob (on the right) and the cally maintains the climate in the cabin of the vehicle at Blower Control knob (on the left) to AUTO.
Page 285 UNDERSTANDING YOUR INSTRUMENT PANEL 283 • Pressing the Air Conditioning Control button while in You will experience the greatest efficiency by simply allowing the system to function automatically. Selecting AUTO mode will cause the LED in the control button the “O” (OFF) position on the blower control stops the to flash three times and then turn off.
Page 286 284 UNDERSTANDING YOUR INSTRUMENT PANEL Blower Control Manual Operation For full automatic operation or for This system offers a full complement of manual override automatic blower operation, turn the features, which consist of Blower Preferred Automatic, knob to the AUTO position. In manual Mode Preferred Automatic, or Blower and Mode Pre- mode there are seven blower speeds ferred Automatic.
Page 287 UNDERSTANDING YOUR INSTRUMENT PANEL 285...
Page 288 286 UNDERSTANDING YOUR INSTRUMENT PANEL • Floor The operator can override the AUTO mode setting to change airflow distribution by rotating the Mode Control Air is directed through the floor outlets with a knob (on the right) to one of the following positions. small amount flowing through the defrost and side window demist outlets.
Page 289 UNDERSTANDING YOUR INSTRUMENT PANEL 287 • Air Conditioner Control NOTE: • When the ignition switch is turned to the LOCK Press this button to turn on the air conditioning during manual operation position, the recirculation feature will be cancelled. only. When the air conditioning is •...
Page 290: Operating Tips
288 UNDERSTANDING YOUR INSTRUMENT PANEL • Most of the time, when in Automatic Operation, you Summer Operation can temporarily put the system into Recirculation The engine cooling system in air-conditioned vehicles Mode by pressing the Recirculation button. However, must be protected with a high-quality antifreeze coolant under certain conditions, while in Automatic Mode, to provide proper corrosion protection and to protect the system is blowing air out the defrost vents.
Page 291 UNDERSTANDING YOUR INSTRUMENT PANEL 289 Window Fogging Outside Air Intake Interior fogging on the windshield can be quickly re- Make sure the air intake, located directly in front of the moved by turning the mode selector to Defrost. The windshield, is free of obstructions such as leaves. Leaves Defrost/Floor mode can be used to maintain a clear collected in the air intake may reduce airflow, and if they windshield and provide sufficient heating.
Page 292 290 UNDERSTANDING YOUR INSTRUMENT PANEL Control Setting Suggestions for Various Weather Conditions...
Page 293 STARTING AND OPERATING CONTENTS Starting Procedures ....295 Manual Transmission — If Equipped ..298 Manual Transmission –...
Page 294 292 STARTING AND OPERATING AutoStick ......308 Brake Assist System (BAS) ....319 Operation .
Page 295 STARTING AND OPERATING 293 Tires — General Information ... . . 338 Replacement Tires ....346 Tire Pressure .
Page 296 294 STARTING AND OPERATING MMT In Gasoline ....361 Trailer Towing ......367 Materials Added To Fuel .
Page 297: Starting Procedures
STARTING AND OPERATING 295 STARTING PROCEDURES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust both • Do not leave the key fob in or near the vehicle. A inside and outside mirrors, and fasten your seat belts. child could operate power windows, other con- trols, or move the vehicle.
Page 298: Automatic Transmission - If Equipped
296 STARTING AND OPERATING Automatic Transmission – If Equipped Simply turn the ignition switch to the START position The shift lever must be in the PARK or NEUTRAL and release when the engine starts. If the engine fails to position before you can start the engine. Apply the brakes start within 15 seconds, turn the ignition switch to the before shifting to any driving gear.
Page 299: Extreme Cold Weather
STARTING AND OPERATING 297 Extreme Cold Weather (Below –20°F or 29°C) WARNING! To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (avail- Never pour fuel or other flammable liquid into the able from your authorized dealer) is recommended. throttle body air inlet opening in an attempt to start the vehicle.
Page 300: Engine Block Heater - If Equipped
298 STARTING AND OPERATING ENGINE BLOCK HEATER — IF EQUIPPED MANUAL TRANSMISSION — IF EQUIPPED The engine block heater warms the engine, and permits Five–Speed Manual Transmission quicker starts in cold weather. Connect the cord to a standard 110-115 Volt AC electrical outlet with a WARNING! grounded, three-wire extension cord.
Page 301: Starting And Operating 299
STARTING AND OPERATING 299 For most city driving, you will find it easier to use only the lower gears. For steady highway driving with light accelerations, fifth gear is recommended. Never drive with your foot resting on the clutch pedal, and never try to hold the vehicle on a hill with the clutch pedal partially engaged.
Page 302: Downshifting
300 STARTING AND OPERATING To maintain a safe speed and prolong brake life, shift Manual Transmission Recommended Shift Speeds down to second or first gear when descending a steep Units in mph (km/h) grade. Accel- Engine 1 to 2 2 to 3 3 to 4 4 to 5 eration...
Page 303 STARTING AND OPERATING 301 CAUTION! (Continued) WARNING! (Continued) • Do not shift between PARK, REVERSE, NEU- • Before exiting a vehicle, always apply the parking TRAL, or DRIVE when the engine is above idle brake, shift the transmission into PARK, and re- speed.
Page 304: Key Ignition Park Interlock
302 STARTING AND OPERATING Key Ignition Park Interlock Interlock System” in this section). To drive, move the shift This vehicle is equipped with a Key Ignition Park Inter- lever from PARK or NEUTRAL to the DRIVE position. lock which requires the shift lever to be placed in PARK NOTE: The Continuously Variable Automatic Transmis- before the ignition switch can be turned to the LOCK/ sion (CVT) changes ratios in a continuous manner.
Page 305: Gear Ranges
STARTING AND OPERATING 303 transmission gear ratios, and will display the current PARK gear in the instrument cluster as 6, 5, 4, 3, 2, 1. This range supplements the parking brake by locking the transmission. The engine can be started in this range. Gear Ranges Never attempt to use PARK while the vehicle is in DO NOT race the engine when shifting from PARK or...
Page 306 304 STARTING AND OPERATING WARNING! WARNING! (Continued) • It is dangerous to move the shift lever out of PARK • Never use the PARK position as a substitute for or NEUTRAL if the engine speed is higher than the parking brake. Always apply the parking idle speed.
Page 307 STARTING AND OPERATING 305 WARNING! (Continued) WARNING! (Continued) • Unintended movement of a vehicle could injure • Allowing children to be in a vehicle unattended is those in or near the vehicle. As with all vehicles, dangerous for a number of reasons. A child or you should never exit a vehicle while the engine is others could be seriously or fatally injured.
Page 308 306 STARTING AND OPERATING REVERSE CAUTION! (Continued) This range is for moving the vehicle backward. Shift into • DO NOT race the engine when shifting from REVERSE only after the vehicle has come to a complete PARK or NEUTRAL into another gear range, as stop.
Page 309 STARTING AND OPERATING 307 using a lower gear will improve performance and extend CAUTION! transmission life by reducing excessive shifting and heat buildup. Towing the vehicle, coasting, or driving for any other reason with the transmission in NEUTRAL can result During sustained high speed driving or trailer towing up in severe transmission damage.
Page 310: Autostick
308 STARTING AND OPERATING AUTOSTICK AutoStick operation is activated in the DRIVE position AutoStick is a driver-interactive transmission that offers by moving the shift lever side-to-side. Moving the shift six manual ratio changes to provide you with more lever to the (+) side will activate AutoStick and shift up control.
Page 311: General Information
STARTING AND OPERATING 309 • When heavy Anti-Lock Brake System (ABS) applica- FOUR-WHEEL DRIVE OPERATION — IF tion is detected EQUIPPED This feature provides full time, on-demand, four–wheel General Information drive (4WD). • If a ratio other than first is selected and the vehicle is brought to a stop, the transmission control logic will automatically select the first gear ratio.
Page 312: On-Road Driving Tips
310 STARTING AND OPERATING traction surfaces, activate the “4WD LOCK” switch by They are not designed for cornering at the same speeds as pulling up once and releasing. This locks the center conventional two-wheel drive vehicles any more than coupling allowing more torque to be sent to the rear low-slung sports cars are designed to perform satisfacto- wheels.
Page 313: Power Steering Fluid Check
STARTING AND OPERATING 311 NOTE: CAUTION! • Increased noise levels at the end of the steering wheel travel are considered normal and do not indicate that Prolonged operation of the steering system at the end there is a problem with the power steering system. of the steering wheel travel will increase the steering fluid temperature and it should be avoided when •...
Page 314: Parking Brake
312 STARTING AND OPERATING If necessary, add fluid to restore to the proper indicated CAUTION! level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to “Fluids, Lubricants, and Genuine Do not use chemical flushes in your power steering Parts”...
Page 315 STARTING AND OPERATING 313 NOTE: • When the parking brake is applied and the automatic transmission is placed in gear, the “Brake Warning Light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle.
Page 316 314 STARTING AND OPERATING WARNING! WARNING! (Continued) • Always fully apply the parking brake when leav- • When leaving the vehicle, always remove the key ing your vehicle or it may roll and cause damage or fob from the ignition and lock your vehicle. injury.
Page 317: Brake System
STARTING AND OPERATING 315 BRAKE SYSTEM If either of the two hydraulic systems lose normal capa- Your vehicle is equipped with power assisted brakes as bility, the remaining system will still function with some standard equipment. In the event power assist is lost for loss of overall braking effectiveness.
Page 318: Anti-Lock Brake System (Abs)
316 STARTING AND OPERATING Anti-Lock Brake System (ABS) WARNING! (Continued) The ABS provides increased vehicle stability and brake • The ABS cannot prevent collisions, including performance under most braking conditions. The system those resulting from excessive speed in turns, automatically “pumps” the brakes during severe braking following another vehicle too closely, or hydro- conditions to prevent wheel lock-up.
Page 319 STARTING AND OPERATING 317 required. However, the conventional brake system will working properly. This self-check occurs each time the continue to operate normally if the “Brake Warning vehicle is started and accelerated past 7 mph (11 km/h). Light” is not on. ABS is activated during braking under certain road or If the “ABS Warning Light”...
Page 320: Electronic Brake Control System
318 STARTING AND OPERATING (HSA), and Electronic Stability Control (ESC). All sys- WARNING! tems work together to enhance vehicle stability and control in various driving conditions and are commonly The Anti-Lock Brake System (ABS) contains sophis- referred to as ESC. ticated electronic equipment that may be susceptible to interference caused by improperly installed or Anti-Lock Brake System (ABS)
Page 321: Brake Assist System (Bas)
STARTING AND OPERATING 319 across a driven axle. If one wheel on a driven axle is “pump” the brakes). Do not reduce brake pedal pressure spinning faster than the other, the system will apply the unless braking is no longer desired. Once the brake pedal brake of the spinning wheel.
Page 322: Electronic Roll Mitigation (Erm)
320 STARTING AND OPERATING Electronic Roll Mitigation (ERM) NOTE: Anytime the ESC system is in the “Full Off” This system anticipates the potential for wheel lift by mode, ERM is disabled. Refer to “Electronic Stability monitoring the driver’s steering wheel input and the Control (ESC)”...
Page 323: Hill Descent Control (Hdc) - If Equipped
STARTING AND OPERATING 321 Hill Descent Control (HDC) – If Equipped Off” button for five seconds. Refer to “Electronic Stability This system maintains vehicle speed while descending Control (ESC)” in this section of the manual. hills during off-road driving situations. HDC will auto- HDC operation can be overridden with brake application matically apply the brakes to control downhill speed to to slow the vehicle down below the HDC control speed.
Page 324: Hill Start Assist (Hsa) - Manual Transmission Only
322 STARTING AND OPERATING HSA Activation Criteria WARNING! The following criteria must be met in order for HSA to activate: HDC is only intended to assist the driver in control- ling vehicle speed when descending hills. The driver • Vehicle must be stopped. must remain attentive to the driving conditions and •...
Page 325 STARTING AND OPERATING 323 Disabling/Enabling HSA 5. Release the clutch pedal. If you wish to turn on or off the HSA system, it can be 6. Rotate the steering wheel one-half turn to the left. done using the Customer Programmable Features in the Electronic Vehicle Information Center (EVIC).
Page 326: Electronic Stability Control (Esc)
324 STARTING AND OPERATING Electronic Stability Control (ESC) WARNING! This system enhances directional control and stability of • The Electronic Stability Control (ESC) cannot pre- the vehicle under various driving conditions. ESC cor- vent the natural laws of physics from acting on the rects for over-steering or under-steering of the vehicle by vehicle, nor can it increase the traction afforded by applying the brake of the appropriate wheel to assist in...
Page 327 STARTING AND OPERATING 325 Full On (Four-Wheel Drive Models) Or On To turn ESC on again, momentarily press the “ESC Off” (Two-Wheel Drive Models) switch. This will restore the normal “ESC On” mode of This is the normal operating mode for ESC. Whenever operation.
Page 328 326 STARTING AND OPERATING “ESC OFF” message will appear in the odometer. Press WARNING! and release the Trip Odometer button located on the instrument cluster to clear this message. When in “Partial Off” mode, the TCS functionality of ESC, (except for the limited slip feature described in In this mode, ESC and TCS, except for the “limited slip”...
Page 329: Esc Activation/Malfunction Indicator Light And Esc Off Indicator Light
STARTING AND OPERATING 327 NOTE: The “ESC OFF” message will display and an ESC Activation/Malfunction Indicator Light And audible chime will sound when the shift lever is placed ESC OFF Indicator Light into the PARK position from any other position, and then The “ESC Activation/Malfunction Indicator moved out of the PARK position.
Page 330: Tire Safety Information
328 STARTING AND OPERATING Malfunction Indicator Light” begins to flash during ac- TIRE SAFETY INFORMATION celeration, ease up on the accelerator and apply as little Tire Markings throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions. NOTE: •...
Page 331 STARTING AND OPERATING 329 • LT (Light Truck) - Metric tire sizing is based on U.S. NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. The size designation for LT-Metric design standards. P-Metric tires have the letter “P” tires is the same as for P-Metric tires except for the molded into the sidewall preceding the size designa- letters “LT”...
Page 332 330 STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ..blank..= Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T or S = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm)
Page 333 STARTING AND OPERATING 331 EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —...
Page 334: Tire Identification Number (Tin)
332 STARTING AND OPERATING Tire Identification Number (TIN) Look for the TIN on the outboard side of black sidewall The TIN may be found on one or both sides of the tire, tires as mounted on the vehicle. If the TIN is not found on however, the date code may only be on one side.
Page 335: Tire Terminology And Definitions
STARTING AND OPERATING 333 Tire Terminology And Definitions Term Definition B-Pillar The vehicle B-Pillar is the structural member of the body located behind the front door. Cold Tire Inflation Pressure Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
Page 336: Tire Loading And Tire Pressure
334 STARTING AND OPERATING Tire Loading And Tire Pressure Tire And Loading Information Placard Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door.
Page 337 STARTING AND OPERATING 335 axles must not be exceeded. For further information on This placard tells you important information about GAWRs, vehicle loading, and trailer towing, refer to the: “Vehicle Loading” in this section. 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of...
Page 338 336 STARTING AND OPERATING 3. Subtract the combined weight of the driver and pas- NOTE: • The following table shows examples on how to calcu- sengers from XXX lbs or XXX kg. late total load, cargo/luggage, and towing capacities 4. The resulting figure equals the available amount of of your vehicle with varying seating configurations cargo and luggage load capacity.
Page 339 STARTING AND OPERATING 337...
Page 340: Tires - General Information
338 STARTING AND OPERATING Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause collisions. recommended load capacity for your vehicle.
Page 341: Tire Inflation Pressures
STARTING AND OPERATING 339 Tire Inflation Pressures WARNING! (Continued) The proper cold tire inflation pressure is listed on the left • Unequal tire pressures from one side of the ve- side “B” Pillar or rear edge of the driver’s side door. hicle to the other can cause the vehicle to drift to Some vehicles may have Supplemental Tire Pressure the right or left.
Page 342 340 STARTING AND OPERATING Tire pressures change by approximately 1 psi (7 kPa) per CAUTION! 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in After inspecting or adjusting the tire pressure, al- the Winter.
Page 343: Tire Pressures For High Speed Operation
STARTING AND OPERATING 341 Tire Pressures For High Speed Operation Radial Ply Tires The manufacturer advocates driving at safe speeds WARNING! within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle...
Page 344: Compact Spare Tire - If Equipped
342 STARTING AND OPERATING vehicle. If your vehicle has this option refer to an Compact Spare Tire – If Equipped authorized tire dealer for the recommended tire rotation The compact spare is for temporary emergency use only. pattern. You can identify if your vehicle is equipped with a compact spare by looking at the spare tire description on If your vehicle is not equipped with an original equip- the Tire and Loading Information Placard located on the...
Page 345: Full Size Spare - If Equipped
STARTING AND OPERATING 343 your original equipment tire, replace (or repair) the WARNING! original equipment tire and reinstall on the vehicle at the first opportunity. Compact spares are for temporary emergency use only. With these spares, do not drive more than Limited-Use Spare –...
Page 346: Tire Spinning
344 STARTING AND OPERATING Refer to “Freeing A Stuck Vehicle” in “What To Do In WARNING! Emergencies” for further information. Limited-use spares are for emergency use only. In- WARNING! stallation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than the Fast spinning tires can be dangerous.
Page 347: Life Of Tire
STARTING AND OPERATING 345 Life Of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style • Tire pressure • Distance driven WARNING! Tires and the spare tire should be replaced after six years, regardless of the remaining tread.
Page 348: Starting And Operating
346 STARTING AND OPERATING Replacement Tires It is recommended you contact your original equipment The tires on your new vehicle provide a balance of many or an authorized tire dealer with any questions you may characteristics. They should be inspected regularly for have on tire specifications or capability.
Page 349: Tire Chains
STARTING AND OPERATING 347 TIRE CHAINS WARNING! (Continued) Due to limited clearance, tire chains are not recom- • Never use a tire with a smaller load index or mended. capacity other than what was originally equipped on your vehicle. Using a tire with a smaller load CAUTION! index could result in tire overloading and failure.
Page 350: Tire Rotation Recommendations
348 STARTING AND OPERATING Snow tires generally have lower speed ratings than what These effects can be reduced by timely rotation of tires. was originally equipped with your vehicle and should The benefits of rotation are especially worthwhile with not be operated at sustained speeds over 75 mph aggressive tread designs such as those on all season type (120 km/h).
Page 351: Tire Pressure Monitoring System (Tpms)
STARTING AND OPERATING 349 The tire pressure will vary with temperature by about 1 psi (6.9 kPa) for every 12°F (6.5°C). This means that when the outside temperature decreases, the tire pressure will decrease. Tire pressure should always be set based on “cold inflation tire pressure”.
Page 352 350 STARTING AND OPERATING The TPMS will continue to warn the driver of low tire For example, your vehicle may have a recommended pressure as long as the condition exists, and will not turn cold (parked for more than three hours) placard pressure off until the tire pressure is at or above the recommended of 30 psi (207 kPa).
Page 353 STARTING AND OPERATING 351 NOTE: CAUTION! • The TPMS is not intended to replace normal tire care • The TPMS has been optimized for the original and maintenance or to provide warning of a tire failure or condition. equipment tires and wheels. TPMS pressures and warnings have been established for the tire size •...
Page 354: Base System
352 STARTING AND OPERATING • Seasonal temperature changes will affect tire pressure, • Four Tire Pressure Monitoring Sensors and the TPMS will monitor the actual tire pressure in • Tire Pressure Monitoring Telltale Light the tire. Tire Pressure Monitoring Low Pressure Warnings Base System The Tire Pressure Monitoring Telltale Light will illumi- This is the TPMS warning indicator located in the...
Page 355 STARTING AND OPERATING 353 Check TPMS Warnings NOTE: Your vehicle is equipped with a compact spare The Tire Pressure Monitoring Telltale Light will flash on wheel and tire assembly. and off for 75 seconds and remain on solid when a system 1.
Page 356: Premium System - If Equipped
354 STARTING AND OPERATING 4. For each subsequent ignition key cycle, a chime will Premium System – If Equipped sound and the Tire Pressure Monitoring Telltale Light The TPMS uses wireless technology with wheel rim will flash on and off for 75 seconds and then remain on mounted electronic sensors to monitor tire pressure lev- solid.
Page 357 STARTING AND OPERATING 355 • Various Tire Pressure Monitoring System Messages, which display in the Electronic Vehicle Information Center (EVIC) • Tire Pressure Monitoring Telltale Light Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitoring Telltale Light will illumi- nate in the instrument cluster and an audible chime will be activated when one or more of the four active road tire pressures are low.
Page 358 356 STARTING AND OPERATING the graphic display of the pressure value(s) will stop flashing, and the Tire Pressure Monitoring Light will extinguish once the updated tire pressure(s) have been received. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this information.
Page 359 STARTING AND OPERATING 357 will be displayed instead of dashes. A system fault can pressure values still shown. This indicates that the pres- occur with any of the following scenarios: sure values are still being received from the TPM sensors but they may not be located in the correct vehicle 1.
Page 360: General Information
358 STARTING AND OPERATING 3. However, after driving the vehicle for up to 20 min- limit in any of the four active road tires. The vehicle may utes above 15 mph (24 km/h), the Tire Pressure Moni- need to be driven for up to 20 minutes above 15 mph toring Telltale Light will flash on and off for 75 seconds (24 km/h) in order for the TPMS to receive this and then remain on solid.
Page 361: Fuel Requirements
STARTING AND OPERATING 359 FUEL REQUIREMENTS Over 40 auto manufacturers worldwide have issued and endorsed consistent gasoline specifications (the World- 2.0L And 2.4L Engine wide Fuel Charter, WWFC) which define fuel properties This engine is designed to meet all emis- necessary to deliver enhanced emissions, performance, sions regulations and provide excellent and durability for your vehicle.
Page 362: Gasoline/Oxygenate Blends
360 STARTING AND OPERATING Gasoline/Oxygenate Blends E-85 Usage In Non-Flex Fuel Vehicles Some fuel suppliers blend unleaded gasoline with oxy- Non-FFV vehicles are compatible with gasoline contain- genates such as Ethanol. Fuels blended with oxygenates ing 10% ethanol (E10). Gasoline with higher ethanol may be used in your vehicle.
Page 363: Mmt In Gasoline
STARTING AND OPERATING 361 • drain the fuel tank (see your authorized dealer) Materials Added To Fuel All gasoline sold in the United States is required to More extensive repairs will be required for prolonged contain effective detergent additives. Use of additional exposure to E-85 fuel.
Page 364: Carbon Monoxide Warnings
362 STARTING AND OPERATING Carbon Monoxide Warnings CAUTION! (Continued) • An out-of-tune engine or certain fuel or ignition WARNING! malfunctions can cause the catalytic converter to Carbon monoxide (CO) in exhaust gases is deadly. overheat. If you notice a pungent burning odor or Follow the precautions below to prevent carbon some light smoke, your engine may be out of tune monoxide poisoning:...
Page 365: Adding Fuel
STARTING AND OPERATING 363 After removing the gas cap, place the gas cap tether cable WARNING! (Continued) over a hook on the inside of the fuel door. This keeps the • Guard against carbon monoxide with proper gas cap suspended away from and protects the vehicle’s maintenance.
Page 366 364 STARTING AND OPERATING CAUTION! WARNING! (Continued) • Never add fuel when the engine is running. This is • Damage to the fuel system or emission control in violation of most state and Federal fire regula- system could result from using an improper fuel tions and may cause the MIL to turn on.
Page 367: Loose Fuel Filler Cap Message
STARTING AND OPERATING 365 Loose Fuel Filler Cap Message Vehicle Certification Label If the vehicle diagnostic system determines that the fuel Your vehicle has a Vehicle Certification Label attached to filler cap is loose or improperly installed, a “gASCAP” the driver’s door B-Pillar. message will be displayed in the Odometer/Trip Odom- The label contains the following information: eter in the instrument cluster.
Page 368 366 STARTING AND OPERATING Gross Vehicle Weight Rating (GVWR) Curb Weight The GVWR is the total allowable weight of your vehicle. The curb weight of a vehicle is defined as the total weight This includes driver, passengers, and cargo. The total of the vehicle with all fluids, including vehicle fuel, at full load must be limited so that you do not exceed the capacity conditions, and with no occupants or cargo...
Page 369: Trailer Towing
STARTING AND OPERATING 367 Overloading can cause potential safety hazards and TRAILER TOWING shorten useful service life. Heavier suspension compo- In this section you will find safety tips and information nents do not necessarily increase the vehicle’s GVWR. on limits to the type of towing you can reasonably do with your vehicle.
Page 370 368 STARTING AND OPERATING exceed the GVWR. Refer to “Vehicle Loading/Vehicle Gross Axle Weight Rating (GAWR) Certification Label” in “Starting and Operating” for The GAWR is the maximum capacity of the front and rear further information. axles. Distribute the load over the front and rear axles evenly.
Page 371 STARTING AND OPERATING 369 Frontal Area Weight-Distributing Hitch The frontal area is the maximum height multiplied by the A weight-distributing system works by applying lever- maximum width of the front of a trailer. age through spring (load) bars. They are typically used for heavier loads, to distribute trailer tongue weight to Trailer Sway Control the tow vehicle’s front axle and the trailer axle(s).
Page 372: Trailer Hitch Classification
370 STARTING AND OPERATING Trailer Hitch Classification Trailer Hitch Classification Definitions Your vehicle may be factory equipped for safe towing of Class Max. Trailer Hitch Industry trailers weighing over 2,000 lbs (907 kg) with the optional Standards Trailer Tow Prep Package. See your authorized dealer for Class I - Light Duty 2,000 lbs (907 kg) package content.
Page 373: Trailer Towing Weights (Maximum Trailer Weight Ratings)
STARTING AND OPERATING 371 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/Transmission Frontal Area Max. GTW (Gross Trailer Wt.) Max. Tongue Wt. (See Note) 2.0L Auto/Man 22 sq ft (2.04 sq m) 1,000 lbs (450 kg) 150 lbs (50 kg)
Page 374: Trailer And Tongue Weight
372 STARTING AND OPERATING Trailer And Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle.
Page 375: Towing Requirements
STARTING AND OPERATING 373 NOTE: Remember that everything put into or on the CAUTION! (Continued) trailer adds to the load on your vehicle. Also, additional • Then, during the first 500 miles (805 km) that a factory-installed options, or authorized dealer-installed trailer is towed, do not drive over 50 mph options, must be considered as part of the total load on (80 km/h) and do not make starts at full throttle.
Page 376 374 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Make certain that the load is secured in the trailer • Vehicles with trailers should not be parked on a and will not shift during travel. When trailering grade. When parking, apply the parking brake on cargo that is not fully secured, dynamic load shifts the tow vehicle.
Page 377 STARTING AND OPERATING 375 Towing Requirements – Tires replacement procedures. Replacing tires with a higher load carrying capacity will not increase the vehicle’s − Do not attempt to tow a trailer while using a compact GVWR and GAWR limits. spare tire. Towing Requirements –...
Page 378 376 STARTING AND OPERATING CAUTION! WARNING! (Continued) • Towing any trailer will increase your stopping If the trailer weighs more than 1,000 lbs (454 kg) distance. When towing you should allow for addi- loaded, it should have its own brakes and they tional space between your vehicle and the vehicle should be of adequate capacity.
Page 379 STARTING AND OPERATING 377 The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. Seven-Pin Connector 1 — Battery 5 — Ground 2 — Backup Lamps 6 —...
Page 380: Towing Tips
378 STARTING AND OPERATING Towing Tips − When using the speed control, if you experience speed Before setting out on a trip, practice turning, stopping drops greater than 10 mph (16 km/h), disengage until and backing the trailer in an area away from heavy you can get back to cruising speed.
Page 381: Recreational Towing (Behind Motorhome, Etc.)
STARTING AND OPERATING 379 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing Condition Wheels OFF the Ground Manual Transmission Automatic Transmission Flat Tow None NOT ALLOWED • Transmission in NEUTRAL • Key in ACC Front NOT ALLOWED OK (FWD Only) Dolly Tow Rear NOT ALLOWED NOT ALLOWED...
Page 382 380 STARTING AND OPERATING CAUTION! • Do not flat tow any vehicle equipped with an automatic transmission. Damage to the drivetrain will result. If these vehicles require towing, make sure all drive wheels are off the ground. • Front or rear wheel lifts should not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when recreational towing.
Page 383 WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flashers ....382 Jump-Starting Procedures ....394 If Your Engine Overheats .
Page 384: Hazard Warning Flashers
382 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the instrument panel, below the radio. potential for overheating by taking the appropriate ac- tion.
Page 385: What To Do In Emergencies 383
WHAT TO DO IN EMERGENCIES 383 CAUTION! WARNING! Driving with a hot cooling system could damage You or others can be badly burned by hot engine your vehicle. If the pointer rises to the H (red) mark, coolant (antifreeze) or steam from your radiator. If the instrument cluster will sound a chime.
Page 386: Jacking And Tire Changing
384 WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING WARNING! (Continued) • Never start or run the engine while the vehicle is WARNING! on a jack. • Do not attempt to change a tire on the side of the •...
Page 387: Jack Location
WHAT TO DO IN EMERGENCIES 385 Jack Location Spare Tire Removal The jack and jack-handle are stowed under the load floor Lift up the load floor cover and remove the hold down. in the cargo area. Preparations For Jacking 1. Park the vehicle on a firm level surface, avoiding ice or slippery areas.
Page 388: Jacking Instructions
386 WHAT TO DO IN EMERGENCIES 5. Turn OFF the ignition. WARNING! (Continued) 6. Block both the front and rear of the • Always park on a firm, level surface as far from wheel diagonally opposite the jacking the edge of the roadway as possible before raising position.
Page 389 WHAT TO DO IN EMERGENCIES 387 WARNING! (Continued) CAUTION! • If working on or near a roadway, be extremely Do not attempt to raise the vehicle by jacking on careful of motor traffic. locations other than those indicated in the Jacking •...
Page 390 388 WHAT TO DO IN EMERGENCIES two triangular cutouts on one of the flanges in the sill CAUTION! flange assembly. The rear location is the same but with two rectangular cutouts. For vehicles equipped with Do not attempt to raise the vehicle by jacking on plastic trim, the plastic has been cut away to expose the locations other than those indicated.
Page 391 WHAT TO DO IN EMERGENCIES 389 3. Turn the jack screw to the left until the jack can be placed under the jacking location. Once the jack is positioned, turn the jack screw to the right until the jack head is properly engaged with the lift area closest to the wheel to be changed.
Page 392 390 WHAT TO DO IN EMERGENCIES 5. Remove the wheel nuts and pull the wheel and wheel covers, where applicable, off the hub. Install the spare wheel and wheel nuts with the cone shaped end of the nuts toward the wheel. Lightly tighten the nuts. WARNING! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle...
Page 393 WHAT TO DO IN EMERGENCIES 391 NOTE: The wheel cover is held on the wheel by the WARNING! wheel nuts. When reinstalling the original wheel, prop- erly align the wheel cover to the valve stem, place the A loose tire or jack thrown forward in a collision or wheel cover onto the wheel, then install the wheel nuts.
Page 394: Road Tire Installation
392 WHAT TO DO IN EMERGENCIES Road Tire Installation Vehicles Equipped With Wheel Covers 1. Mount the road tire on the axle. 2. To ease the installation process for steel wheels with wheel covers, install two lug nuts on the mounting studs which are on each side of the valve stem.
Page 395 WHAT TO DO IN EMERGENCIES 393 3. Align the valve notch in the wheel cover with the 6. Finish tightening the lug nuts. Push down on the valve stem on the wheel. Install the cover by hand, wrench while at the end of the handle for increased snapping the cover over the two lug nuts.
Page 396: Jump-Starting Procedures
394 WHAT TO DO IN EMERGENCIES 5. After 25 miles (40 km) check the lug nut torque with a WARNING! torque wrench to ensure that all lug nuts are properly seated against the wheel. To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle is JUMP-STARTING PROCEDURES lowered to the ground.
Page 397: Preparations For Jump-Start
WHAT TO DO IN EMERGENCIES 395 Preparations For Jump-Start CAUTION! The battery in your vehicle is located in the front of the engine compartment below the air intake duct. To access Do not use a portable battery booster pack or any the battery remove the air intake duct by turning the two other booster source with a system voltage greater finger screws, located on the radiator support.
Page 398 396 WHAT TO DO IN EMERGENCIES WARNING! • Take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • Remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact.
Page 399: Jump-Starting Procedure
WHAT TO DO IN EMERGENCIES 397 3. If using another vehicle to jump-start the battery, park CAUTION! the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is OFF. Failure to follow these procedures could result in damage to the charging system of the booster vehicle WARNING! or the discharged vehicle.
Page 400 398 WHAT TO DO IN EMERGENCIES 4. Connect the opposite end of the negative (-) jumper Once the engine is started, remove the jumper cables in cable to a good engine ground (exposed metal part of the the reverse sequence: discharged vehicle’s engine) away from the battery and 6.
Page 401: Freeing A Stuck Vehicle
WHAT TO DO IN EMERGENCIES 399 CAUTION! CAUTION! Accessories that can be plugged into the vehicle Racing the engine or spinning the wheels may lead to power outlets draw power from the vehicle’s battery, transmission overheating and failure. Allow the en- even when not in use (i.e., cellular phones, etc.).
Page 402: Shift Lever Override
400 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! • When “rocking” a stuck vehicle by moving be- Fast spinning tires can be dangerous. Forces gener- tween DRIVE and REVERSE (with automatic ated by excessive wheel speeds may cause damage, or transmission) or 1st gear and Reverse (with even failure, of the axle and tires.
Page 403 WHAT TO DO IN EMERGENCIES 401 3. Turn the ignition switch to the ON/RUN position without starting the engine (engine OFF). 4. Press and maintain firm pressure on the brake pedal. 5. Using a small screwdriver or similar tool, push and hold the override release lever forward.
Page 404: Towing A Disabled Vehicle
402 WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE AUTOMATIC MANUAL Towing Condition Wheels OFF the Ground TRANSMISSION TRANSMISSION Transmission in Flat Tow NONE NOT ALLOWED NEUTRAL Rear NOT ALLOWED NOT ALLOWED Wheel Lift or Dolly Tow Front FWD Models ONLY FWD Models ONLY Flatbed BEST METHOD...
Page 405: With Ignition Key
WHAT TO DO IN EMERGENCIES 403 • FWD vehicles can be towed with the front wheels With Ignition Key elevated. Automatic Transmission • FWD or 4WD vehicles can be towed on a flatbed truck • Front Wheel Drive (FWD) vehicles can be towed with (all wheels OFF the ground).
Page 406: Without The Ignition Key
404 WHAT TO DO IN EMERGENCIES If the vehicle’s battery is discharged, see “Shift Lever Without The Ignition Key Override” in “What To Do In Emergencies” for instruc- Special care must be taken when the vehicle is towed tions on shifting the automatic transmission out of the with the ignition in the LOCK/OFF position.
Page 407 MAINTAINING YOUR VEHICLE CONTENTS Engine Compartment — 2.0L ... . . 407 Maintenance Procedures ....412 Engine Compartment —...
Page 408 406 MAINTAINING YOUR VEHICLE Exhaust System ..... 421 Vehicle Storage ..... . . 444 Cooling System .
Page 409: Engine Compartment - 2.0L
MAINTAINING YOUR VEHICLE 407 ENGINE COMPARTMENT — 2.0L 1 — Washer Fluid Reservoir 6 — Air Cleaner Filter 2 — Power Steering Fluid Reservoir 7 — Coolant Pressure Cap 3 — Engine Oil Fill 8 — Engine Oil Dipstick 4 — Brake Fluid Reservoir 9 —...
Page 410: 408 Maintaining Your Vehicle
408 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 2.4L 1 — Washer Fluid Reservoir 6 — Air Cleaner Filter 2 — Power Steering Fluid Reservoir 7 — Coolant Pressure Cap 3 — Engine Oil Fill 8 — Engine Oil Dipstick 4 — Brake Fluid Reservoir 9 —...
Page 411: Onboard Diagnostic System - Obd Ii
MAINTAINING YOUR VEHICLE 409 ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard • Prolonged driving with the MIL on could cause diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic further damage to the emission control system.
Page 412: Emissions Inspection And Maintenance Programs
410 MAINTAINING YOUR VEHICLE persists, the message will appear the next time the Normally, the OBD II system will be ready. The OBD II vehicle is started. This might indicate a damaged cap. If system may not be ready if your vehicle was recently the problem is detected twice in a row, the system will serviced, recently had a dead battery or a battery replace- turn on the MIL.
Page 413: Replacement Parts
MAINTAINING YOUR VEHICLE 411 4. Approximately 15 seconds later, one of two things will Regardless of whether your vehicle’s OBD II system is happen: ready or not, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced a.
Page 414: Dealer Service
412 MAINTAINING YOUR VEHICLE DEALER SERVICE MAINTENANCE PROCEDURES Your authorized dealer has the qualified service person- The pages that follow contain the required maintenance nel, special tools, and equipment to perform all service services determined by the engineers who designed your operations in an expert manner.
Page 415: Engine Oil
MAINTAINING YOUR VEHICLE 413 fully warmed engine is shut off. Do not check oil level CAUTION! (Continued) before starting the engine after it has sat overnight. • Your vehicle has been built with improved fluids Checking engine oil level when the engine is cold will that protect the performance and durability of give you an incorrect reading.
Page 416 414 MAINTAINING YOUR VEHICLE Engine Oil Selection CAUTION! For best performance and maximum protection for all engines under all types of operating conditions, the Do not overfill the engine. Overfilling the engine manufacturer recommends engine oils that are API Cer- will cause oil aeration, which can lead to loss of oil tified and meet the requirements of Chrysler Material pressure and an increase in oil temperature.
Page 417 MAINTAINING YOUR VEHICLE 415 Synthetic Engine Oils CAUTION! You may use synthetic engine oils provided the recom- mended oil quality requirements are met, and the recom- Do not use chemical flushes in your engine oil as the mended maintenance intervals for oil and filter changes chemicals can damage your engine.
Page 418: Engine Oil Filter
416 MAINTAINING YOUR VEHICLE station, or governmental agency for advice on how and WARNING! where used oil and oil filters can be safely discarded in your area. The air cleaner can provide a measure of protection in the case of engine backfire. Do not remove the air Engine Oil Filter cleaner unless such removal is necessary for repair or The engine oil filter should be replaced with a new filter...
Page 419: Maintenance-Free Battery
MAINTAINING YOUR VEHICLE 417 Maintenance-Free Battery WARNING! (Continued) Your vehicle is equipped with a maintenance-free battery. • Battery gas is flammable and explosive. Keep You will never have to add water, nor is periodic main- flame or sparks away from the battery. Do not use tenance required.
Page 420: Air Conditioner Maintenance
418 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance CAUTION! For best possible performance, your air conditioner • It is essential when replacing the cables on the should be checked and serviced by an authorized dealer at the start of each warm season. This service should battery that the positive cable is attached to the include cleaning of the condenser fins and a performance positive post and the negative cable is attached to...
Page 421: Body Lubrication
MAINTAINING YOUR VEHICLE 419 Protection Agency and is an ozone-saving product. How- WARNING! ever, the manufacturer recommends that air conditioning • Use only refrigerants and compressor lubricants service be performed by authorized dealers or other service facilities using recovery and recycling equipment. approved by the manufacturer for your air condi- tioning system.
Page 422: Windshield Wiper Blades
420 MAINTAINING YOUR VEHICLE hood latching components to ensure proper function. from a dry windshield. Avoid using the wiper blades to When performing other underhood services, the hood remove frost or ice from the windshield. Make sure that latch, release mechanism and safety catch should be they are not frozen to the glass before turning them on to cleaned and lubricated.
Page 423: Exhaust System
MAINTAINING YOUR VEHICLE 421 When refilling the washer fluid reservoir, take some Exhaust System washer fluid and apply it to a cloth or towel and wipe The best protection against carbon monoxide entry into clean the wiper blades, this will help blade performance. the vehicle body is a properly maintained engine exhaust To prevent freeze-up of your windshield washer system system.
Page 424 422 MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Exhaust gases can injure or kill. They contain • The catalytic converter requires the use of un- carbon monoxide (CO), which is colorless and leaded fuel only. Leaded gasoline will destroy the odorless. Breathing it can make you unconscious effectiveness of the catalyst as an emissions con- and can eventually poison you.
Page 425 MAINTAINING YOUR VEHICLE 423 Under normal operating conditions, the catalytic con- To minimize the possibility of catalytic converter dam- verter will not require maintenance. However, it is im- age: portant to keep the engine properly tuned to assure • Do not shut off the engine or interrupt the ignition, proper catalyst operation and prevent possible catalyst when the transmission is in gear and the vehicle is in damage.
Page 426: Cooling System
424 MAINTAINING YOUR VEHICLE Cooling System rusty in appearance, the system should be drained, flushed and refilled with fresh engine coolant (anti- WARNING! freeze). Check the front of the A/C condenser for any accumulation of bugs, leaves, etc. If dirty, clean by gently •...
Page 427 MAINTAINING YOUR VEHICLE 425 Selection Of Coolant CAUTION! (Continued) Refer to “Fluids, Lubricants, and Genuine Parts” in • Do not use water alone or alcohol based engine “Maintaining Your Vehicle” for further information. coolant (antifreeze) products. Do not use addi- tional rust inhibitors or antirust products, as they CAUTION! may not be compatible with the radiator engine...
Page 428 426 MAINTAINING YOUR VEHICLE Please review these recommendations for using Hybrid Please note that it is the owner’s responsibility to main- Organic Additive Technology (HOAT) engine coolant tain the proper level of protection against freezing ac- (antifreeze). When adding engine coolant (antifreeze): cording to the temperatures occurring in the area where the vehicle is operated.
Page 429 MAINTAINING YOUR VEHICLE 427 rules for your community. To prevent ingestion by ani- WARNING! mals or children do not store ethylene glycol-based • The warning words “DO NOT OPEN HOT” on engine coolant (antifreeze) in open containers or allow it to remain in puddles on the ground.
Page 430 428 MAINTAINING YOUR VEHICLE • Check the coolant freeze point in the radiator and in long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. the coolant recovery bottle. If engine coolant (anti- freeze) needs to be added, the contents of the coolant When additional engine coolant (antifreeze) is needed to recovery bottle must also be protected against freezing.
Page 431: Brake System
MAINTAINING YOUR VEHICLE 429 • Do not change the thermostat for Summer or Winter Brake Master Cylinder operation. If replacement is ever necessary, install The fluid level in the master cylinder should be checked ONLY the correct type thermostat. Other designs may when performing under hood services, or immediately if result in unsatisfactory engine coolant (antifreeze) per- the brake system warning light is on.
Page 432 430 MAINTAINING YOUR VEHICLE brake fluid reservoir is low and the brake system does WARNING! (Continued) not indicate any leaks or other problems, it may be a • To avoid contamination from foreign matter or result of a leak in the hydraulic clutch release system. See moisture, use only new brake fluid or fluid that your local authorized dealer for service.
Page 433: Automatic Transmission (Cvt) - If Equipped
MAINTAINING YOUR VEHICLE 431 Automatic Transmission (CVT) – If Equipped WARNING! (Continued) Selection Of Lubricant • Do not allow petroleum based fluid to contami- It is important that the proper lubricant is used in the nate the brake fluid. Brake seal components could transmission to assure optimum transmission perfor- be damaged, causing partial or complete brake mance.
Page 434: Manual Transmission - If Equipped
432 MAINTAINING YOUR VEHICLE Special Additives level checked immediately. Operation with incorrect Do not add any materials (other than leak detection dyes) fluid level can cause severe transmission damage. to Continuously Variable Transmission (CVT) Fluid Fluid And Filter Changes (CVTF+4 ). CVTF+4 is an engineered product and its Refer to the “Maintenance Schedule”...
Page 435: Rear Drive Assembly (Rda) - Awd/4Wd Models Only
MAINTAINING YOUR VEHICLE 433 Frequency Of Fluid Change fill plug. The fluid level should be maintained between Under normal operating conditions, the fluid installed at the bottom of the fill hole to 1/8 in (4 mm) below the fill the factory will give satisfactory lubrication for the life of hole.
Page 436: Appearance Care And Protection From Corrosion
434 MAINTAINING YOUR VEHICLE the fill plug. The fluid level should be maintained be- hot or cold weather and other extreme conditions will tween the bottom of the fill hole to 1/8 in (4 mm) below have an adverse effect on paint, metal trim, and under- the fill hole.
Page 437 MAINTAINING YOUR VEHICLE 435 Washing CAUTION! • Wash your vehicle regularly. Always wash your ve- • Do not use abrasive or strong cleaning materials hicle in the shade using MOPAR Car Wash or a mild such as steel wool or scouring powder, which will car wash soap, and rinse the panels completely with scratch metal and painted surfaces.
Page 438 436 MAINTAINING YOUR VEHICLE • If you detect any stone chips or scratches in the paint, Wheel And Wheel Trim Care touch them up immediately. The cost of such repairs is • All wheels and wheel trim, especially aluminum and considered the responsibility of the owner.
Page 439 MAINTAINING YOUR VEHICLE 437 Stain Repel Fabric Cleaning Procedure – If Interior Care Equipped Use MOPAR Total Clean or equivalent to clean fabric Stain Repel seats may be cleaned in the following man- upholstery and carpeting. ner: Use MOPAR Total Clean or equivalent to clean vinyl •...
Page 440 438 MAINTAINING YOUR VEHICLE Glass Surfaces WARNING! All glass surfaces should be cleaned on a regular basis with MOPAR Glass Cleaner or any commercial Do not use volatile solvents for cleaning purposes. household-type glass cleaner. Never use an abrasive type Many are potentially flammable, and if used in cleaner.
Page 441 MAINTAINING YOUR VEHICLE 439 Instrument Panel Bezels 1. Clean with a wet, soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive CAUTION! cleaners. If soap is used, wipe clean with a clean, damp rag.
Page 442: Fuses
440 MAINTAINING YOUR VEHICLE FUSES Integrated Power Module The Integrated Power Module is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini-fuses. A label that identifies each component may be printed on the inside of the cover.
Page 443 MAINTAINING YOUR VEHICLE 441 Cavity Cartridge Mini- Description Cavity Cartridge Mini- Description Fuse Fuse Fuse Fuse 10 Amp Rear Center Brake 20 Amp Power Locks/Interior Light Switch Yellow Lighting 10 Amp Ignition Switch/ 15 Amp Power Outlet Occupant Classifica- Lt Blue tion Module 20 Amp 115V AC Inverter –...
Page 444 Module/Occupant Classification Module 10 Amp Intrusion Module/ Siren – If Equipped Hot Car (No Fuse Required) 10 Amp Heating, AC/ Compass 20 Amp Heated Seat – If Yellow Equipped 15 Amp Auto Shutdown Relay Lt Blue 10 Amp Headlamp Washer –...
Page 445 MAINTAINING YOUR VEHICLE 443 Cavity Cartridge Mini- Description CAUTION! Fuse Fuse • When installing the IPM cover, it is important to 10 Amp J1962 Conn/ ensure the cover is properly positioned and fully Powertrain Control latched. Failure to do so may allow water to get Module into the IPM, and possibly result in an electrical 30 Amp...
Page 446: Vehicle Storage
444 MAINTAINING YOUR VEHICLE VEHICLE STORAGE REPLACEMENT BULBS If you will not be using your vehicle for more than All the inside bulbs are brass or glass wedge base. 21 days, you may want to take steps to preserve your Aluminum base bulbs are not approved and should not battery.
Page 447: Bulb Replacement
MAINTAINING YOUR VEHICLE 445 2. Reach into the engine compartment and pull the red LIGHTS BULBS – Exterior Bulb No. lock out at the green connector. Low Beam Headlamp ..... H11 High Beam Headlamp .
Page 448: Rear Turn Signal And Backup Lamp
446 MAINTAINING YOUR VEHICLE Rear Turn Signal And Backup Lamp 3. Twist and remove socket from lamp. 1. Remove the two push-pins from the taillamp housing. 4. Remove bulb from socket and replace. License Lamps 1. Use a screw driver to gently pry against the side of the snap tab to remove the lamp from the liftgate.
Page 449: Fluid Capacities
MAINTAINING YOUR VEHICLE 447 FLUID CAPACITIES U.S. Metric Fuel (Approximate) 13.6 Gallons 51.5 Liters Engine Oil with Filter 2.0L and 2.4L Engine (SAE 5W-20, API Certified) 4.5 Quarts 4.26 Liters Cooling System * 2.0L and 2.4L Engine (MOPAR Engine Coolant/Antifreeze 5 7.2 Quarts 6.8 Liters Year/100,000 Mile Formula or equivalent)
Page 450: Fluids, Lubricants, And Genuine Parts
448 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant MOPAR Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hy- brid Organic Additive Technology) or equivalent. Engine Oil Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395.
Page 451: Chassis
MAINTAINING YOUR VEHICLE 449 Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission (CVT) – If MOPAR CVTF+4 Continuously Variable Transmission Fluid Equipped Manual Transmission – If Equipped MOPAR ATF+4 Automatic Transmission Fluid or equivalent licensed ATF+4 product. Rear Drive Assembly (RDA) MOPAR Gear &...
Page 453: Maintenance Schedules
MAINTENANCE SCHEDULES CONTENTS Maintenance Schedule ....452 Required Maintenance Intervals ..454...
Page 454 452 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE On Non-EVIC equipped vehicles, “Change Oil” will flash The Scheduled Maintenance services listed in this in the instrument cluster odometer and a single chime manual must be done at the times or mileages specified will sound, indicating that an oil change is necessary. to protect your vehicle warranty and ensure the best Based on engine operation conditions, the oil change vehicle performance and reliability.
Page 455 MAINTENANCE SCHEDULES 453 NOTE: referring to the steps described under “Electronic Vehicle • The oil change indicator message will not monitor the Information Center (EVIC)/Oil Change Required” in time since the last oil change. Change your vehicle’s “Understanding Your Instrument Panel” or under “In- oil if it has been six months since your last oil change, strument Cluster Description/Odometer/Trip Odom- even if the oil change indicator message is NOT...
Page 456 454 MAINTENANCE SCHEDULES Once A Month At Each Oil Change • Check the tire pressure and look for unusual wear or • Change the engine oil filter. damage. • Inspect the brake hoses and lines. • Inspect the battery and clean and tighten the terminals CAUTION! as required.
Page 457 MAINTENANCE SCHEDULES 455 8,000 Miles (13,000 km) or 16,000 Miles (26,000 km) or 12 Months Maintenance Service 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 458: Service Schedule
456 MAINTENANCE SCHEDULES 24,000 Miles (39,000 km) or 32,000 Miles (52,000 km) or 24 Months Maintenance Service 18 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 459 MAINTENANCE SCHEDULES 457 40,000 Miles (65,000 km) or 48,000 Miles (78,000 km) or 36 Months Maintenance Service 30 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 460 458 MAINTENANCE SCHEDULES 56,000 Miles (91,000 km) or 64,000 Miles (104,000 km) or 48 Months Maintenance Service 42 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 461 MAINTENANCE SCHEDULES 459 72,000 Miles (117,000 km) or 80,000 Miles (130,000 km) or 60 Months Maintenance Service 54 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 462 460 MAINTENANCE SCHEDULES 88,000 Miles (143,000 km) or 66 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 88,000 miles (143 000 km). Odometer Reading Date Repair Order #...
Page 463 MAINTENANCE SCHEDULES 461 96,000 Miles (156,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 96,000 miles (156 000 km). ❏...
Page 464 462 MAINTENANCE SCHEDULES 104,000 Miles (169,000 km) or 112,000 Miles (182,000 km) or 84 Months Maintenance Service 78 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 465 MAINTENANCE SCHEDULES 463 120,000 Miles (195,000 km) or 128,000 Miles (208,000 km) or 96 Months Maintenance Service 90 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 466 464 MAINTENANCE SCHEDULES 136,000 Miles (221,000 km) or 144,000 Miles (234,000 km) or 108 Months Maintenance Service 102 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 467 MAINTENANCE SCHEDULES 465 152,000 Miles (247,000 km) or 114 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 152,000 miles (247 000 km). Odometer Reading Date Repair Order #...
Page 468 466 MAINTENANCE SCHEDULES WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
Page 469 IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Customer Assistance For The Hearing Or Vehicle......469 Speech Impaired (TDD/TTY) .
Page 470 468 IF YOU NEED CONSUMER ASSISTANCE Department Of Transportation Uniform Tire Traction Grades ..... 475 Quality Grades ......475 Temperature Grades .
Page 471: Suggestions For Obtaining Service For Your Vehicle
IF YOU NEED CONSUMER ASSISTANCE 469 SUGGESTIONS FOR OBTAINING SERVICE FOR the service advisor and list the items in order of priority. YOUR VEHICLE At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the...
Page 472: 470 If You Need Consumer Assistance
470 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized Chrysler Group LLC Customer Center dealer’s service manager first. Most matters can be re- P.O. Box 21–8004 solved with this process. Auburn Hills, MI 48321–8004 Phone: (877) 426–5337 •...
Page 473: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
IF YOU NEED CONSUMER ASSISTANCE 471 Customer Assistance For The Hearing Or Speech the manufacturer’s service contracts. If you purchased a Impaired (TDD/TTY) manufacturer’s service contract, you will receive Plan To assist customers who have hearing difficulties, the Provisions and an Owner Identification Card in the mail manufacturer has installed special TDD (Telecommuni- within three weeks of the vehicle delivery date.
Page 474: Warranty Information
472 IF YOU NEED CONSUMER ASSISTANCE We appreciate that you have made a major investment WARRANTY INFORMATION when you purchased the vehicle. An authorized dealer See the Warranty Information Booklet, located on the has also made a major investment in facilities, tools, and DVD, for the terms and provisions of Chrysler Group training to assure that you are absolutely delighted with LLC warranties applicable to this vehicle and market.
Page 475: In Canada
IF YOU NEED CONSUMER ASSISTANCE 473 If NHTSA receives similar complaints, it may open an In Canada investigation, and if it finds that a safety defect exists in If you believe that your vehicle has a safety defect, you a group of vehicles, it may order a recall and remedy should contact the Customer Service Department imme- campaign.
Page 476 474 IF YOU NEED CONSUMER ASSISTANCE • Service Manuals • Owner’s Manuals These comprehensive Service Manuals provide the These Owner’s Manuals have been prepared with the information that students and professional technicians assistance of service and engineering specialists to need in diagnosing/troubleshooting, problem solving, acquaint you with specific Chrysler Group LLC ve- maintaining, servicing, and repairing Chrysler Group hicles.
Page 477 IF YOU NEED CONSUMER ASSISTANCE 475 DEPARTMENT OF TRANSPORTATION UNIFORM significantly from the norm due to variations in driving TIRE QUALITY GRADES habits, service practices, and differences in road charac- The following tire grading categories were established by teristics and climate. the National Highway Traffic Safety Administration.
Page 478 476 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades WARNING! The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat The temperature grade for this tire is established for and its ability to dissipate heat, when tested under a tire that is properly inflated and not overloaded.
Page 479: Index
INDEX...
Page 480 478 INDEX ABS (Anti-Lock Brake System) ....316 Airbag, Window (Side Curtain) ... 64,66,69 Adding Engine Coolant (Antifreeze) ..425 Alarm Light .
Page 481 B-Pillar Location ......334 Calibration, Compass ..... 222 Battery .
Page 482 Check Engine Light Compass ......211 (Malfunction Indicator Light) ....410 Compass Calibration .
Page 483 INDEX 481 Cooling System ......424 Diagnostic System, Onboard ....409 Adding Coolant (Antifreeze) .
Page 484 482 INDEX Electronic Roll Mitigation ....320 Oil Change Interval ....414 Traction Control System .
Page 485 INDEX 483 Flashers ......382 Fuel ......359,448 Hazard Warning .
Page 486 484 INDEX Garage Door Opener (HomeLink®) ... 160 Hands-Free Phone (Uconnect™) ....98 Gas Cap (Fuel Filler Cap) ... . 363,365,409 Hazard Warning Flasher .
Page 487 INDEX 485 Hood Release ......146 Jack Location ......385 Jack Operation .
Page 488 486 INDEX Life of Tires ......345 Fog ......149,210,445 Liftgate (Sedan) .
Page 489 INDEX 487 Loading Vehicle ..... . 365,367 Frequency of Fluid Change ... 433,434 Capacities .
Page 490 488 INDEX Monitor, Tire Pressure System ....349 Filter ......416 Mopar Parts .
Page 491 INDEX 489 Phone, Hands-Free (Uconnect™) ....98 Radial Ply Tires ......341 Placard, Tire and Loading Information .
Page 492 490 INDEX Remote Starting System ....25 Satellite Radio Antenna ....240,265 Replacement Bulbs .
Page 493 INDEX 491 Rear Folding (Sedan) ....144 Signals, Turn ..... . 87,199,446 Seatback Release .
Page 494 492 INDEX Steering Wheel Mounted Sound Tie Down Hooks, Cargo ....186 System Controls ......275 Tilt Steering Column .
Page 495 INDEX 493 Pressure Warning Light ....205 Trailer Towing ......367 Quality Grading .
Page 496 Washing Vehicle ......435 Variance, Compass ..... . . 223 Wheel and Wheel Trim .
Page 497 INDEX 495 Wind Buffeting ......172 Windshield Defroster ... . . 86,279,280,286 Window Fogging .
Page 498 Antennas for two-way radios should be mounted on the roof or the rear area of the vehicle. Care should be used in mounting antennas with magnet bases. Magnets may affect the accuracy or operation of the compass on vehicles so equipped.
Page 499 Chrysler Group LLC 4th Edition Printed in U.S.A. 12MK49-126-AD...

This manual is also suitable for:

2012 compass

Jeep Compass Owner's Manual

Table of Contents

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

Starting and Operating

Starting and Operating

Quick Links

Chapters

Related Manuals for Jeep Compass

Summary of Contents for Jeep Compass