Barco DP2K SLP Series Service Manual page 401

dmd red - temperature too high 320
dmd red fan - speed low 311–313
electronics fan 1 (top side) - speed low 304
electronics fan 2 (bottom side) - speed low 304
engine air - temperature high 338
engine air - temperature sensor open 338
engine air - temperature sensor short 339
engine air - temperature too high 338
engine fan - speed low 298
icp fan - speed low 343
imb - logical marriage tamper event 334
imb - no communication 333
imb - physical marriage tamper event 335
imb - service door tamper event 334
LCB - force light off 320
lcb – +12v too high 377
lcb – +12v too low 377
lcb – +24v (fans) too high 346
lcb – +24v (fans) too low 346
lcb – +36v (diffusor wheel) too high 347
lcb – +36v (diffusor wheel) too low 347
lcb – 36v phosphor wheel voltage too high 363
lcb – 36v phosphor wheel voltage too low 363
lcb – air pressure too low 346
LCB – Board temperature sensor open 345
LCB – Board temperature sensor shorted 345
lcb – Board temperature too high 345
lcb – fcb forces lasers off 347
lcb – fcb forces lasers off at start-up 349
lcb – ldm power configuration mismatch 350
lcb – turn-on lcm 1 failed 349
lcb – turn-on pfc ldm 1 failed 349
lcb – turn-on pfc ldm 1–6 failed 350
lcb – turn-on pfc ldm 1–7 failed 350
lcm 1 – air blown out temperature open 353
lcm 1 – air blown out temperature short 353
lcm 1 – air drawn in temperature sensor
open 354
lcm 1 – air drawn in temperature sensor
short 353
lcm 1 – air drawn in temperature too high 353
lcm 1 – air drawn in temperature too low 353
lcm 1 – coolant liquid in temperature too
high 352–353
lcm 1 – coolant liquid in temperature too low 352
lcm 1 – coolant liquid out temperature too
high 351–352
lcm 1 – coolant liquid out temperature too
low 351
lcm 1 – fan 2 speed too low 350
lcm 1 – fan 3 speed too low 377
lcm 1 – fan 4 speed too low 378
lcm 1 – fan 5 speed too low 378
lcm 1 – fan 6 speed too low 378
lcm 1 – not configured (invalid module type) 375
lcm 1 – not configured (no communication) 375
lcm 1 – pump speed too high 351
lcm 1 – pump speed too low 351
lcm 1– fan 1 speed too low 350
ldm 1 - heatsink pfc aux temperature sensor
open 355
ldm 1 - heatsink pfc aux temperature sensor
short 355
ldm 1 - heatsink pfc aux temperature too
high 355
ldm 1 - heatsink rectifier temperature sensor
open 356
ldm 1 - heatsink rectifier temperature sensor
short 355
ldm 1 - heatsink rectifier temperature too
high 355
ldm 1 - mains voltage too high 355
ldm 1 – +12v voltage too high) 358
ldm 1 – +12v voltage too low) 358
ldm 1 – +24v voltage too high) 358
ldm 1 – +24v voltage too low) 358
ldm 1 – bad communication 356, 359
ldm 1 – board temperature too high) 359
ldm 1 – fan 1 speed too high 357
ldm 1 – fan 1 speed too low 357
ldm 1 – fan 2 speed too high 358
ldm 1 – fan 2 speed too low 358
ldm 1 – no communication 356, 359
ldm 1 – not configured (initialization failed) 356–
357
ldm 1 – not configured (initialization failure) 359
ldm 1 – not configured (invalid module type) 356,
359
ldm 1 – not configured (not initialized) 375
ldm 1-2 - lls bank 1 not white point calibrated 372
ldm 1-2 - lls bank 2 not white point calibrated 373
ldm 1-2 - lls bank 3 not white point calibrated 373
ldm 1-2 – bad communication 362
ldm 1-2 – heatsink drain temperature sensor
open 362
ldm 1-2 – heatsink drain temperature sensor
shorted 362
ldm 1-2 – heatsink drain temperature too
high 362
ldm 1-2 – lls bank 1 current too high) 360
ldm 1-2 – lls bank 1 drain voltage too high) 359,
368
ldm 1-2 – lls bank 1 temperature sensor
open) 361
ldm 1-2 – lls bank 1 temperature sensor
shorted) 360
ldm 1-2 – lls bank 1 temperature too high) 360
ldm 1-2 – lls bank 2 current too high 360
ldm 1-2 – lls bank 2 drain power too high 368
ldm 1-2 – lls bank 2 drain voltage too high 360
ldm 1-2 – lls bank 2 temperature sensor
open 361
ldm 1-2 – lls bank 2 temperature sensor
shorted 361
ldm 1-2 – lls bank 2 temperature too high 361
ldm 1-2 – lls bank 3 current too high 360
ldm 1-2 – lls bank 3 drain power too high 368
ldm 1-2 – lls bank 3 drain voltage too high 360
ldm 1-2 – lls bank 3 temperature sensor
open 361
ldm 1-2 – lls bank 3 temperature sensor
shorted 361
ldm 1-2 – lls bank 3 temperature too high 361
ldm 1-2 – no communication 362
ldm 1-3 - lls bank 4 not white point calibrated 373
ldm 1-3 - lls bank 5 not white point calibrated 373
R5906848 /04
Index
DP2K SLP Series 401