Table of Contents
Advertisement
Quick Links
W I N D A L E P L AY S Y S T E M – F 2 3 2 2 0
INSTALLATION AND OPERATING INSTRUCTIONS
10'-10"
26'
8-10 Hrs
Two person
assembly
KidKraft, Inc.
4630 Olin Road
Dallas, Texas 75244 USA
customerservice@kidkraft.com
canadacustomerservice@kidkraft.com
1.800.933.0771
972.385.0100
For online parts replacement visit
https://parts.kidkraft.com/
WARNING
and give them to any future owner of this play system. Manufacturer contact information provided below.
OBSTACLE FREE SAFETY ZONE - 24'11"x 26' (7.348m x 7.924m) area requires Protective Surfacing. See page 3.
MAXIMUM VERTICAL FALL HEIGHT - 6'5"
CAPACITY - 9 Users Maximum, Ages 3 to 10; Weight Limit 110 lbs. (49.9 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools, churches, nurseries, day cares or parks.
Warning. Only for domestic use.
KidKraft Netherlands BV
Olympisch Stadion 8
1076 DE Amsterdam
The Netherlands
europecustomerservice@kidkraft.com
+31 20 305 8620 M-F from 09:00 to 17:30
(GMT+1)
For online parts replacement visit
https://parts.kidkraft.eu/
To reduce the risk of serious injury or death, you must read and
follow these instructions. Keep and refer to these instructions often
Table of Contents
Warnings And Safe Play Instructions. . . . . . . . . . . . . . . pg. 2
Protective Surfacing Guidelines. . . . . . . . . . . . . . . . . . . pg. 3
Instructions For Proper Maintenance . . . . . . . . . . . . . . . pg. 4
About Our Wood – Limited Warranty . . . . . . . . . . . . . . pg. 5
Keys To Assembly Success . . . . . . . . . . . . . . . . . . . . . . pg. 6
Metric Conversion Sheets . . . . . . . . . . . . . . . . . . . . . pg. 7,8
Part ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 9
Installation of I.D./Warning Plaque . . . . . . . . . . . .Final Step
9403220
Rev 06/16/2020
Advertisement
Table of Contents
Related Manuals for KidKraft WINDALE
Summary of Contents for KidKraft WINDALE
- Page 1 Protective Surfacing Guidelines....pg. 3 Instructions for Proper Maintenance ....pg. 4 KidKraft, Inc. KidKraft Netherlands BV 4630 Olin Road Olympisch Stadion 8 About Our Wood –...
- Page 2 Warnings and Safe Play Instructions CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using this play system.
- Page 3 Protective Surfacing - Reducing Risk of Serious Head Injury From Falls. One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable for the equipment height in accordance with ASTM F1292.
- Page 4 Instructions for Proper Maintenance Your KidKraft Play System is designed and constructed of quality materials with your child’s safety in mind. As with all outdoor products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your Play Set, it is important that you, the owner, properly maintain it.
- Page 5 About Our Wood KidKraft Premium Play Systems uses only premium playset lumber, ensuring the safest product for your children’s use. Although we take great care in selecting the best quality lumber available, wood is still a product of nature and susceptible to weathering which can change the appearance of your set.
- Page 6 Keys to Assembly Success Tools Required • 3/16” Hex Key • Tape Measure • #1, #3 Phillips or Robertson • Open End Wrench • Carpenters Level bit or Screwdriver (1/2”, 7/16” & 9/16”) • 8’ Step Ladder • Carpenters Square •...
- Page 9 Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Actual Size 3602232 Nominal Size 3pc. - 2232 - Door Siding 3/8 x 3 1/2 x 11-13/16" - Box 2 - "...
- Page 10 Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) 3672217 2pc. - 2217 - Seat Support 1 x 4 x 35-7/8" - Box 2 - Actual Size Nominal Size " x 3 " 1 x 4 " x 4½" 1 x 5 "...
- Page 11 Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Nominal Size CE Rock Board B 1 x 6 x 17 3671777 3pc. - 1777 - " - Box 2 - Actual Size 1 x 6 " x 5 " 5/4 x 2 "...
- Page 12 Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Floor Gusset 2 x 3 x 11 3670367 Nominal Size Actual Size 2pc. - 0367 - " - Box 2 - 2 x 2 1½" x 1½" 2 x 3 1 "...
- Page 13 2 person Glider Seat Yellow 1X 3320386 Rocks (5pk) 3-Green 2-Yellow 1X 3310148 1X 9320374 Slide 48" High Rail -Green KidKraft I.D Plaque w hardware 1X 3533860 39" Glider Rope & Chain (4pk) w. welded chain 1X 3200184 Triangle Plate (4pk)
- Page 14 Hardware Identification (Actual Size) 1/4 x 3" 1/4 x 1-1/2" 3pc. LS3 - Lag Screw - (9262230) 4pc. LS1 - Lag Screw - (9262212) Hex Bolt 1/4 x 1-1/2" 5pc. H1 - - (9277212) Hex Bolt 1/4 x 2" 26pc. H2 - - (9277220) Hex Bolt 1/4 x 2-1/2"...
- Page 15 Hardware Identification (Actual Size) 47pc. TN1 - 1/4" T - Nut (9285200) 14pc. LW2 - 5/16" Lock Washer - (9253300) 6pc. FW3 - #8 Flat Washer - (9251500) 52pc. LW1 - 1/4" Lock Washer - (9253200) 16pc. FW0 - 3/16" Flat Washer - (9251100) 14pc.
- Page 16 Before you discard your cartons fill out the form below. • The carton I.D. stamp is located on the end of each carton.The tracking number is located on the KidKraft ID Plaque (9320374). • Please retain this information for future reference. You will need this information if you contact the Consumer Relations Department.
- Page 17 Step 2: Rock Wall Assembly Fig. 2.1 Note: The holes in the rock boards 1777 must orient to the 0349 1778 top of the boards. 1777 1778 1777 1779 7-3/4” Approx Note: Gaps between boards 2-1/4”, not to exceed 2-3/8” A: Lay 2 (0349) Rock Rails down, side by side with angled edges facing down.
- Page 18 Step 3: Swing Beam Assembly Warning: For your child’s safety, Fig. 3.4 orientate the swing hangers as shown to ensure your swing will have proper swing motion when installed. Failure to do so could result in premature failure of the swing hanger or swing chain.
- Page 19 Step 4: Swing End Assembly A: Attach 2 (1863) SW Posts to (1856) SW Upright using 2 (G4) 5/16 x 4” Hex Bolts (with lock washer, flat washer and t-nut). (fig. 4.1) Fig. 4.1 5/16” Lock Washer 1863 5/16” Flat Washer 1862 1856...
- Page 20 Step 5: Attach Swing End to Swing Beam A: Place (4919) SW Rail Block in the centre between (1826) Front Beam and (1825) Back Beam and attach with 1 (H8) 1/4 x 4-1/4” Hex Bolt (with lock washer, flat washer and t-nut). (fig. 5.1 & 5.2) Fig.
- Page 21 Step 6: Roof Assembly Part 1 A: Attach 1 (1424) Roof Support to another at the peak using 1 (S4) #8 x 3” Wood Screw. Do this twice so you have 2 Roof Support Assemblies. (fig. 6.1) B: Attach 1 (1425) Roof Joist to another at the peak using 1 (S4) #8 x 3” Wood Screw. (fig. 6.1) C: Place the Roof Supports and Joist Assemblies in the pattern shown in fig.
- Page 22 Step 6: Roof Assembly Part 2 D: Starting at the top of the Roof Support Assembly attach 1 (1930) Siding on each side of the (1424) Roof Supports and (1425) Roof Joists with 3 (S0) #8 x 7/8” Truss Screws per board. (fig. 6.2) Be sure to overlap the top of the boards so there are no gaps.
- Page 23 Step 7: Cafe Wall Assembly Note: Pre-drill all holes using a 1/8” drill bit before installing the lag screws. A: On the ground lay flat 2 (2215) Posts then loosely attach (2221) Side Ground (in the bottom holes), (1934) End Floor (in the top holes), (2203) Cafe Side Top and (1935) Side Roof using 2 (H2) 1/4 x 2” Hex Bolts (with lock washer, flat washer and t-nut) per board as shown in fig.
- Page 24 Step 8: Swing Wall Assembly A: Loosely attach (2223) SW Ground using 4 (H2) 1/4 x 2” Hex Bolts (with lock washer, flat washer and t-nut); (2211) Floor End (in the top holes); (2224) SW Side and (1935) Side Roof using 2 (H2) 1/4 x 2” Hex Bolts (with lock washer, flat washer and t-nut) for each board to 2 (2215) Posts.
- Page 25 Step 9: Front Wall Assembly A: With both the Front and Back Walls facing each other, on the side with longer extension of (1935) Side Roof, loosely attach (2210) Front Back Ground to the (2215) Posts with 2 (H4) 1/4 x 4” Hex Bolts (with lock washer, flat washer and t-nut).
- Page 26 Step 10: Back Frame Assembly A: On the opposite side of the assembly loosely attach (2210) Front Back Ground to the (2215) Posts with 2 (H4) 1/4 x 4” Hex Bolts (with lock washer, flat washer and t-nut). (fig. 10.1) B: Loosely attach (1894) Back Floor to both (2215) Posts using 2 (H5) 1/4 x 4-1/2”...
- Page 27 Step 11: Attach Floor Gussets Note: Pre-drill all holes using a 1/8” drill bit before installing the lag screws. A: Make sure the assembly is square before proceeding. Assemble Gussets and square fort B: Measure 4-3/8” down from the bottom of (2211) Floor End, place 1 (0367) Floor Gusset against each (2215) Post on the Swing Wall at measured location and tight against (2211) Floor End.
- Page 28 Step 12: Attach Joists A: Loosen the top bolt and remove the middle and bottom bolts in (2228) Wall Mount. Do not discard these bolts, you will re-install them after the (1903) Floor Joist is attached. (fig. 12.1) B: From inside of the assembly, measure 3/4” up from the bottom of (2211) Floor End and (1934) End Floor (fig. 12.2) and then attach (1903) Floor Joist to each board using the pilot holes with 2 (S4) #8 x 3”...
- Page 29 Step 13: Attach Gap and Floor Boards Floor Boards A: Place 1 (2207) Cedar Gap Board at each end of the assembly. Then starting on the Swing Wall side place 2 (2206) Cedar Floor Boards, 1 (2208) Centre Gap Board so the gap in the board fits around the (2213) Front Divider, and 2 more (2206) Cedar Floor Boards.
- Page 30 Step 14: Swing Side Wall Assembly A: In between both (2215) Posts on Swing Wall attach 4 (2227) Wall Boards to (2211) Floor End and (2224) SW Side using 4 (S0) #8 x 7/8” Truss Screws per board. Make sure the bottom of the boards are tight against (2207) Cedar Gap Board.
- Page 31 Step 15: Cafe Side Wall Assembly A: In between both (2215) Posts on Cafe Wall evenly space and attach 5 (2227) Wall Boards to (1934) End Floor and (2203) Cafe Side Top using 4 (S0) #8 x 7/8” Truss Screws per board. Make sure the bottom of the boards are tight against (2207) Cedar Gap Board.
- Page 32 Step 16: Back Wall Assembly A: On the Back Wall, tight to the floor boards, attach 1 (1227) CE Wall Board to the outside of (2215) Post on Cafe Wall side with 2 (S2) #8 x 1-1/2” Wood Screws and to the inside face of (2200) Back Divider with 2 (S1) #8 x 1-1/8”...
- Page 33 Step 17: Front Wall Window Assembly A: On the Front Wall, tight to (1906) Top Front Back and flush to the outside of (2215) Post and (2213) Front Divider, attach (2226) Wall Board with 4 (S2) #8 x 1-1/2” Wood Screws (fig. 17.1 and 17.2) B: Tight to the bottom of (2226) Wall Board attach 1 (2222) Side Window flush to the outside of both (2215) Post and (2213) Front Divider with 4 (S2) #8 x 1-1/2”...
- Page 34 Step 18: Attach Seat Support A: On the Swing Wall measure 27” up from the bottom of (2223) SW Ground on each (2215) Post. Place top of (2217) Seat Support at marked location and attach to both posts with 4 (S2) #8 x 1-1/2” Wood Screws. (fig. 18.1) Fig.
- Page 35 Step 19: Attach Rock Rail to Fort A: Place Rock Wall Assembly from Step 2 centred between (2215) Post and (2200) Back Divider, flush to top of (1894) Back Floor (fig. 19.1 and 19.2). Attach (0349) Rock Rails to (1894) Back Floor using 4 (S15) #8 x 1-3/4” Wood Screws as shown in fig.
- Page 36 Step 20: Lower Cafe Wall Assembly A: Place 1 (1808) Short Trim tight to the top of (2221) Side Ground and flush to the outside edge of (2215) Post on the Front Wall side of the assembly. Attach to (2215) Post with 3 (S2) #8 x 1-1/2” Wood Screws. (fig. 20.1 and 20.2) B: Tight to top of (2221) Side Ground and tight to (1808) Short Trim attach (2220) Siding to both (2215) Posts with 2 (S0) #8 x 7/8”...
- Page 37 Step 21: Cafe Seat Assembly A: Loosely attach 1 (2202) Cafe Leg to each (2210) Front Back Ground with 2 (H1) 1/4 x 1-1/2” Hex Bolts (with lock washer, flat washer and t-nut) per board. (fig. 21.1 and 21.2) B: Attach 1 (2201) Cafe Gusset tight to each (2202) Cafe Leg with 1 (S15) #8 x 1-3/4” Wood Screw per board in the top pilot holes and 1 (S3) #8 x 2-1/2”...
- Page 38 Part A Step 22: Front Lower Wall Assembly Part 1 A: On the Front Wall, tight to the bottom of (1906) Top Front Back and flush to the outside of (2215) Post and (2213) Front Divider, attach (2226) Wall Board with 4 (S2) #8 x 1-1/2” Wood Screws (fig. 22.1 and 22.2) B: Tight to the bottom of (2226) Wall Board attach 1 (2222) Side Window flush to the outside of both (2215) Post and (2213) Front Divider with 4 (S2) #8 x 1-1/2”...
- Page 39 Step 22: Front Lower Wall Assembly Part 2 Front Lower Wall E: Evenly space 5 (2219) Siding between (2214) Lower Window and the bottom (2219) Siding, flush to the Part B outside of both (2215) Post and (2213) Front Divider, making sure there are no gaps between boards. Attach with 2 (S0) #8 x 7/8”...
- Page 40 Step 23: Attach Ground Stakes MOVE FORT TO FINAL LOCATION. FINAL LOCATION MUST BE LEVEL GROUND WARNING: To prevent tipping and avoid potential injury, stakes must be driven 10-1/2” into ground. Digging or driving stakes can be dangerous if you do not check first for underground wiring, cables or gas lines. A: Drive 2 (0318) Ground Stakes 10-1/2”...
- Page 41 Step 24: Attach Door Stop to Fort A: From inside the fort measure 16-7/8” up from the bottom of (2213) Front Divider and attach (2209) Door Stop flush to the inside edge of (2213) Front Divider with 3 (S15) #8 x 1-3/4” Wood Screws. (fig. 24.1) B: In the notched out opening of (2209) Door Stop attach the Magnetic Catch using 2 (S18) #6 x 1”...
- Page 42 Step 25: Door Assembly Part 1 A: Place 1 (2230) Door Cross flush to the bottom and outside edges of (2057) Door Side Right and (2058) Door Side Left. (fig. 25.1) B: Place the second (2230) Door Cross in the middle notches of (2057) Door Side Right and (2058) Door Side Left, flush to the outside edges.
- Page 43 Step 25: Door Assembly Part 2 F: On the outside face of the Door Assembly place Small Window in the window gap and attach with 8 (S13) #6 x 5/8” Pan Screws. (fig. 25.3) G: On the outside of the Door Assembly place 1 Door Handle centred over the top (2230) Door Cross, as shown in fig.
- Page 44 Step 25: Door Assembly Part 3 I: On the inside of Door Assembly, measure 16-3/4” up from the bottom of (2058) Door Side Left and attach Catch Plate using 2 (S18) #6 x 1” Wood Screws. (fig.25.4 and 25.5) J: Place a second Door Handle on the inside of the Door Assembly at approximately the same spot as the first then attach with 2 (S13) #6 x 5/8”...
- Page 45 Step 26: Attach Door Assembly to Fort A: In the opening for the door on the Front Wall, measure 5/8” up from the top of (2210) Front Back Ground then attach remaining side of the Door Hinges to (2215) Post with 3 (S13) #6 x 5/8” Pan Screws per hinge. (fig. 26.1, 26.2 and 26.3) Fig.
- Page 46 Step 27: Attach Cafe Canopy to Fort A: Feed Cafe Canopy Frame through the pocket of the Cafe Canopy. (fig. 27.2) B: With a helper, hold the Cafe Canopy Frame against the (2215) Posts on the Cafe Wall. The top of the canopy should rest flush to the top of (1934) End Floor and pulled tight.
- Page 47 Step 28: Attach Roof to Fort Part 1 A: With two helpers place the Roof Assembly, from Step 6, on the fort as shown in fig. 28.1. All four corners of the roof should be flush to the bottoms of both (1935) Side Roof. (fig. 28.1 and 28.2) B: Predrill and attach (1935) Side Roof to the Roof Assembly at all four corners with 2 (S2) #8 x 1-1/2”...
- Page 48 Step 28: Attach Roof to Fort Part 2 C: On this inside of the assembly attach 1 (1663) Roof Arch to each (1424) Roof Support Assembly with 4 (S2) #8 x 1-1/2” Wood Screws per arch. The sides of the arch should be tight to the (1930) Siding. (fig. 28.3 and 28.4) Fig.
- Page 49 Step 29: Attach Slide to Fort A: Place Slide in the centre between (2213) Front Divider and (2215) Post. (fig. 29.1 and 29.2) B: Pre-drill with a 1/8” drill bit then attach slide to fort through floor boards and into (2218) Short Joist using 3 (S7) #12 x 2”...
- Page 50 Step 30: Attach Swing Assembly to Fort A: Attach Swing Assembly from Step 5 to (2228) Wall Mount with 1 (G5) 5/16 x 4-1/2” Hex Bolt (with lock washer, flat washer and t-nut) and 1 (G8) 5/16 x 2” Hex Bolt (with 2 flat washers and 1 lock nut) as shown in fig.
- Page 51 Step 31: Attach Swing Ground Stakes A: Drive one (0318) Ground Stake 10-1/2” into the ground at each (1863) SW Post and attach with 2 (S3) #8 x 2-1/2” Wood Screws per ground stake. (fig. 31.1 and 31.2) WARNING: To prevent tipping and avoid potential injury, stakes must be driven 10-1/2”...
- Page 52 Step 32: Glider Assembly A: Attach 1 Glider End to the Glider Seat using 1 (Z) 5/16 x 6” Hex Bolt (with 2 flat washers and 1 lock nut). Repeat for the second Glider End. (fig. 32.1) B: Install 2 Glider Rope with Chains into each Glider End using 2 - 5/16” Flat Washers and 1 Lock Nut per rope. (fig.
- Page 53 Step 33: Attach Glider and Swings If Bolt protrudes WARNING: beyond T-Nut Check entire play centre for bolts protruding beyond T-Nuts. Use Use an extra extra washers to eliminate this condition. Flat Washer A: Connect the assembled Glider to the Glider Hangers previously installed. (fig. 33.1) B: Attach 2 Belt Swings to the Bolt-Thru Swing Hangers.
- Page 54 Final Step: Attach I.D. Plaque Final Step: Attach I.D Plaque ATTACH THIS WARNING & I.D. PLAQUE TO A PROMINENT LOCATION ON YOUR PLAY EQUIPMENT! (Fort or Swing Post) This provides warnings concerning safety and important contact information. A Tracking Number is provided to allow you to get critical information or order replacement parts for this specific model...
- Page 55 NOTES NOTES...
- Page 56 Would you recommend the purchase of our products to friends and family? Comments: MAIL TO: Fill out your registration card online at KidKraft https://prdregistration.kidkraft.com/ 4630 Olin Road Dallas, TX 75244 United States KidKraft would like to say Thank You for Attention: Customer Service your time and feedback.