Kohler Decision-Maker 3000 Operation page 37

Menu Summary List
Overview
Menu
Available as scrolling or
fixed display text
D Active Shutdowns (if
present)
D Active Warnings (if
present)
D Genset State
D Average Volts
Line-to-Line
D Frequency
D Current
D Average kW
D Coolant Temperature
D Oil Pressure
D Fuel Level % (with
diesel-powered models
and optional fuel tank
sender)
D Fuel Pressure (with
gas-powered models and
optional sender)
D Battery DC Voltage
D Engine Run Time
D Software Version
Engine Metering
Menu
D Engine Speed
(Tachometer)
D Oil Pressure
D Coolant Temperature
D Fuel Level (with
diesel-powered models
and optional fuel tank
sender)
D Battery DC Voltage
D Fuel Pressure (with
gas-powered models and
optional sender)
* User-Defined (changeable) Menu Displays. Use SiteTecht software to change other settings including User-Defined Menu Displays.
NOTE: Some changes require activating the calibration or adjustment mode. Some displays may only appear when in the calibration or adjustment
mode. Refer to Section 2.6 Reviewing Menu Displays to activate the calibration or adjustment mode.
TP-6694 7/11
(Legend: D First level submenu, d second level submenu)
Generator Metering
Menu
D Total Power kVA (shown
as actual output values)
D Total Power kW (shown
as actual output values)
D Rated Power
D Volts, L1--L2 *
D Volts, L2--L3 *
D Volts, L3--L1 *
D Volts, L1--N *
D Volts, L2--N *
D Volts, L3--N *
D Current, L1 *
D Current, L2 *
D Current, L3 *
D Frequency
D Reset Calibration (User
can reset individual volt
and current values or
reset all values)
GenSet Information
Menu
D Generator Set Model No.
D Generator Set Serial No.
D Controller Serial No.
GenSet Run Time
Menu
D Engine Run Time
D Engine Loaded
D Engine Starts
D Total Energy kWh
GenSet System
Menu
D System Frequency
D System Phase (Single
Phase, Single Phase
Dogleg, Three Phase
Wye, or Three Phase
Delta)
D System Volts
D Power Rating
D Amp Rating
D Power Type (Standby or
Prime)
D Battery DC Voltage
D Measurement System
(Metric or English) *
D Contrast (display) *
D Alarm Silence (Always or
Auto Only)
GenSet Calibration
Menu (Before Version
3.0.25)
D Enter Calibration
(Yes or No) *
d Volts, L1--L2
d Volts, L2--L3
d Volts, L3--L1
d Volts, L1--N
d Volts, L2--N
d Volts, L3--N
d Current, L1
d Current, L2
d Current, L3
d Reset Calibration
d Reset All Calibration
(Yes or No)
d Exit Calibration
Voltage Regulator
Menu (Before Version
3.0.25)
D Enter Voltage Regulator?
(Yes or No) *
d Voltage Regulator
Adjust
d Exit Voltage Regulator
Voltage Regulator
Menu (Version 3.0.25 or
Higher)
D Voltage Regulator Voltage
Adjust *
D Reset Voltage Regulator
Settings *
d Reset Voltage
Regulator?
Digital Inputs
Menu
D DIn A1
D DIn A2
D DIn A3
D DIn B1 (with I/O Board)
D DIn B2 (with I/O Board)
Digital Outputs
Menu
D DOut A1
D DOut B1 (with I/O Board)
D DOut B2 (with I/O Board)
D DOut B3 (with I/O Board)
D DOut B4 (with I/O Board)
D DOut B5 (with I/O Board)
Analog Inputs
Menu
D AIn A1 (factory reserved
and not user
programmable)
D AIn A2
D AIn B1 (with I/O Board)
D AIn B2 (with I/O Board)
Event Log
Menu
D See 1.2.4 for a list of
items that can appear in
Event Log
Volt Select
Menu (Version 2.8.22 or
Higher)
D Volt Select: *
d 120/240 V 1 Ph
d 120/208 V 3 Ph
d 139/240 V 3 Ph
d 277/480 V 3 Ph
d 120/240 V 3 Ph
Section 2 Operation 37