ABB 2600T Series Instruction Manual page 77

2 6 0 0 T S E R I E S | P R E S S U R E T R A N S M I T T E R S | O I/ 2 6 6/ F F - E N R E V. E
Diagnostic, BlOCK_ERR and Status Byte
In this table are grouped together the errors produced by the same item. In addition, for each error is specified the corresponding
standard BLOCK_ERR bit, the Error Code shown in the HMI Diagnostic page and the Status Byte assumed by the dynamic variables
of the Pressure Transducer Block.
Cat . Error
Electronics errors
Memory Failure
Electronic Interface
error.
Non-Volatile memory
burn error
Pressure sensor errors
Sensor Invalid
Sensor Memory Fail
P-dP Sensor Fail
Static Pressure Sensor
Fail
Sensor Temperature
Fail
NonVolatile memory
burn error
Installation / start-up errors
Out of Service
Input Simulation
Active
Replace Info
Process errors
Pressure Overrange
P-dP Out Of Limit
Static Pressure Out Of
Limit
Sensor Temperature
Out Of Limit
Max. Working Pressure
Exceeded
Block err HMI code PRTB_x_VALUE Status
PRIMARY
RB.Lost NV Data F116.023 BAD Device Failure No Limit
RB.Device Needs
M030.020 GOOD_NC Non Specific No Limit
Maintenance Soon
RB.Device Needs
M026.024 GOOD_NC Non Specific No Limit
Maintenance Soon
PRIMARY
PRTB.Sensor
F120.016 BAD Sensor Failure No Limit
Failure
PRTB.Sensor
F118.017 BAD Sensor Failure No Limit
Failure
PRTB.Sensor BAD Sensor
F114.003
Failure Failure No Limit
UNCERTAIN
Sensor
PRTB.Sensor
Conversion Not
F112.001
Failure
Accurate No
Limit
UNCERTAIN
Sensor
PRTB.Sensor
Conversion Not
F110.002
Failure
Accurate No
Limit
RB.Device Needs
Maintenance Soon M028.018 GOOD_NC Non Specific No Limit
PRIMARY
RB.Out of Service GOOD_NC Non Specific No Limit
PRTB.Local
C088.030 GOOD_NC Non Specific No Limit
Override
RB.Device Needs
Maintenance Soon M020.007 GOOD_NC Non Specific No Limit
PRIMARY
BAD Non
PRTB.Other F104.011 Specific No
Limit
UNCERTAIN
PRTB.Other F102.004 Non Specific No
Limit
UNCERTAIN
Sensor
PRTB.Other F100.005 Conversion Not
Accurate No
Limit
UNCERTAIN
Sensor
PRTB.Other S054.006 Conversion Not
Accurate No
Limit
PRTB.Other M052.031 GOOD_NC Non Specific No Limit
SECONDARY TERTIARY QUATERNARY
SECONDARY TERTIARY QUATERNARY
GOOD_NC Non GOOD_NC
BAD Sensor Failure No
Specific No Non Specific
Limit
Limit No Limit
GOOD_NC Non BAD Sensor UNCERTAIN Sensor
Specific No Failure No Conversion Not Accurate
Limit Limit No Limit
BAD Sensor
Failure No UNCERTAIN Sensor Conversion Not Accurate No Limit
Limit
SECONDARY TERTIARY QUATERNARY
Note:The AI1,2,3 OUT Goes to BAD
SECONDARY TERTIARY QUATERNARY
GOOD_NC Non Specific No
BAD Non Specific No Limit
Limit
GOOD_NC Non Specific No UNCERTAIN Non Specific
Limit No Limit
GOOD_NC Non UNCERTAIN UNCERTAIN Sensor
Specific No Non Specific Conversion Not Accurate
Limit No Limit No Limit
UNCERTAIN
Non Specific UNCERTAIN Sensor Conversion Not Accurate No Limit
No Limit
7 7
PDP_TRIM SP_TRIM
PDP_TRIM SP_TRIM
GOOD_NC Non
Specific No
Limit
BAD Sensor
Failure No Limit
PDP_TRIM SP_TRIM
PDP_TRIM SP_TRIM
GOOD_NC Non
Specific No
Limit
GOOD_NC Non
Specific No
Limit
UNCERTAIN
Non Specific
No Limit