ABB 2600T Series Instruction Manual page 52

52 2 6 0 0 T S E R I E S | P R E S S U R E T R A N S M I T T E R S | O I/ 2 6 6/ F F - E N R E V. E
. . .Block Mapping
Idx Parameter
16 RESTART
17 FEATURES
18 FEATURES_SEL
19 CYCLE_TYPE
20 CYCLE_SEL
21 MIN_CYCLE_T
22 MEMORY_SIZE
23 NV_CYCLE_TIME
24 FREE_SPACE
25 FREE_TIME
26 SHED_RCAS
27 SHED_ROUT
28 FAULT_STATE
29 SET_FSTATE
30 CLR_FSTATE
31 MAX_NOTIFY
32 LIM_NOTIFY
33 CONFIRM_TIME
34 WRITE_LOCK
35 UPDATE_EVT
36 BLOCK_ALM
37 ALARM_SUM
38 ACK_OPTION
39 WRITE_PRI
40 WRITE_ALM
41 ITK_VER
42 CB_SW_REV
Description / Range / Selections / Notes
0 Uninitialized
1 Run
2 Restart resource
3 Restart with default
4 Restart process
5 Special Restart
6 Special Operations
Used to show supported resource block options
Used to select resource block options. For the 266 PdP they are:
Identifies the block execution methods for this resource
Bit 1 Scheduled
Completion of block
Bit 2
execution
Time duration of the shorted cycle interval of which the resource is capable.
Available configuration memory in the empty resource. To be checked before attempting a download
Minimum time interval for writing copies of NV parameters to non-volatile memory. Zero means it will be never
automatically copied.
Percent of memory available for further configuration. Zero in a preconfigured device
Percent of the block processing time that is free to process additional blocks.
Time duration at which to give up on computer writes to function block Rcas locations. Shed from Rcas shall never
happen when Shed_Rcas = 0
Time duration at which to give up on computer writes to function block Rout locations. Shed from Rout shall never
happen when Shed_Rout = 0
Fault State
Set Fault State
Clear Fault State
Maximum number of unconfirmed alert notify messages possible
Maximum number of unconfirmed alert notify messages allowed
The min time between retries of alert report. Retries shall not happen when Confirm_Time = 0
1 Unlocked (default),
2 Locked
This alert is generated by any change to the static data
"The block alarm is used for all configuration, hardware, connection failure or system problems in the block. The
cause of the alert is entered in the subcode field. The first alert to become active will set the Active Status in the
status parameter. As soon as the Unreported status is cleared by the alert reporting task, another block alert may be
reported without clearing the Active Status, if the subcode has changed"
The alert status associated to the function block
0 Auto Ack Disabled (default) Selection of whether alarms associated the function block
1 Auto Ack Enabled
Priority of the alarm generated by clearing the write_lock
This alert is generated if the write_lock parameter is cleared
Major revision number of the Interoperability test case used in certifying this device as interoperable. See the ITK
version used for the 266 PdP registration from
"XX.YY.ZZ" (07.02.01)
See also SPECIAL_RESTART (index 76)
See also SPECIAL_OPERATION (Index 77)
Bit 1
Bit 2
Bit 3
Bit 4
Bit 10
Used to select the block execution methods for this
resource.
If locked is selected, no writes are allowed except than
Unlock.
Block inputs will continue to be updated
will be automatically acknowledged
https://www.fieldcommgroup.org/registered-products
Reports Supported
Fault State Supported
SW Write Lock Supported
HW Write Lock Supported
Multi-bit Alarm (Bit-Alarm) Support