D-Link DES-3350SR Command Line Interface Reference Manual
  1. Manuals
  2. Brands
  3. D-Link Manuals
  4. Switch
  5. DES-3350SR
  6. Command line interface reference manual
D-Link DES-3350SR Command Line Interface Reference Manual

D-Link DES-3350SR Command Line Interface Reference Manual

Layer 3 switch
Hide thumbs Also See for DES-3350SR:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Reference Manual, User Manual
DES-3350SR
Layer 3 Switch

Command Line Interface

Reference Manual
First Edition (August 2003)
6ES3350SRC01
Printed In Taiwan
RECYCLABLE

Advertisement

Table of Contents
loading

Related Manuals for D-Link DES-3350SR

Summary of Contents for D-Link DES-3350SR

  • Page 1: Command Line Interface

    DES-3350SR Layer 3 Switch Command Line Interface Reference Manual First Edition (August 2003) 6ES3350SRC01 Printed In Taiwan RECYCLABLE...

  • Page 2: Wichtige Sicherheitshinweise

    Wichtige Sicherheitshinweise Bitte lesen Sie sich diese Hinweise sorgfältig durch. Heben Sie diese Anleitung für den spätern Gebrauch auf. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Vervenden Sie keine Flüssig- oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung.
  • Page 3 18. Zum Netzanschluß dieses Gerätes ist eine geprüfte Leitung zu verwenden, Für einen Nennstrom bis 6A und einem Gerätegewicht grőßer 3kg ist eine Leitung nicht leichter als H05VV-F, 3G, 0.75mm2 einzusetzen.

  • Page 4: Limitation Of Liability

    This Warranty applies on the condition that the product Registration Card is filled out and returned to a D-Link office within ninety (90) days of purchase. A list of D-Link offices is provided at the back of this manual, together with a copy of the Registration Card.
  • Page 5 Any package returned to D-Link without an RMA number will be rejected and shipped back to Purchaser at Purchaser's expense, and D-Link reserves the right in such a case to levy a reasonable handling charge in addition mailing or shipping costs.
  • Page 6 D-Link's applicable product documentation, will be corrected.

  • Page 7: Copyright Statement

    The product's Registration Card, provided at the back of this manual, must be sent to a D-Link office. To obtain an RMA number for warranty service as to a hardware product, or to obtain warranty service as to a software product, contact the D-Link office nearest you.
  • Page 8 VCCI Warning BSMI Warning...

  • Page 9: Table Of Contents

    Introduction ... 11 Using the Console CLI ... 16 Command Syntax... 24 Basic Switch Commands... 28 Switch Port Commands ... 48 Network Management Commands ... 52 Download/Upload Commands ... 88 Network Monitoring Commands ... 92 Spanning Tree Commands ... 100 Forwarding Database Commands...
  • Page 10 RIP Commands ... 285 DVMRP Commands... 294 PIM Commands... 303 IP Multicasting Commands ... 310 MD5 Configuration Commands ... 314 OSPF Configuration Commands... 319 SNTP Commands ... 355 Command History List ... 360 Technical Specifications ... 366 Switch System Messages ... 369...

  • Page 11: Introduction

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide NTRODUCTION The switch can be managed through the switch’s serial port, Telnet, or the Web-based management agent. The Command Line Interface (CLI) can be used to configure and manage the switch via the serial port or Telnet interfaces.
  • Page 12 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide With the serial port properly connected to a management computer, the following screen should be visible. If this screen does not appear, try pressing Ctrl+R to refresh the console screen. Figure 1-1. Initial Console screen.
  • Page 13 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide The switch is also assigned a unique MAC address by the factory. This MAC address cannot be changed, and can be found from the initial boot console screen – shown below. Figure 1-2. Boot Screen The switch’s MAC address can also be found from the Web...
  • Page 14 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide represent the IP address to be assigned to the IP interface named System and the y’s represent the corresponding subnet mask. 2. Alternatively, you can enter config ipif System ipaddress xxx.xxx.xxx.xxx|z. represent the IP address to be assigned to the IP interface named System and the z represents the corresponding number of subnets in CIDR notation.
  • Page 15 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide via Telnet and the CLI or via the Web-based management agent using the above IP address to connect to the switch.

  • Page 16: Using The Console Cli

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide SING THE The DES-3350SR supports a console management interface that allows the user to connect to the switch’s management agent via a serial port and a terminal or a computer running a terminal emulation program.
  • Page 17 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide terminal emulator program (e.g., the HyperTerminal program included with the Windows operating system) using an RS-232C serial cable. Your terminal parameters will need to be set to: • VT-100 compatible • 9,600 baud •...
  • Page 18 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Figure 2-1. Initial Console Screen Commands are entered at the command prompt, local>. There are a number of helpful features included in the CLI. Entering the ? command will display a list of all of the top-level...
  • Page 19 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Figure 2-2. The ? Command The dir command has the same function as the ? command. When you enter a command without its required parameters, the CLI will prompt you with a Next possible completions: message.
  • Page 20 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Figure 2-3. Example Command Parameter Help In this case, the command config account was entered with the parameter <username>. The CLI will then prompt you to enter <username> with message, Next possible completions:.
  • Page 21 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Figure 2-4. Using the Up Arrow to Re-enter a Command In the above example, the command config account was entered without the required parameter <username>, the CLI returned the Next possible completions: <username> prompt.
  • Page 22 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Figure 2-5. The Available Commands Prompt The top-level commands consist of commands like show or config. Most of these commands require one or more parameters to narrow the top-level command. This is equivalent to show what? or config what? Where the what? is the next parameter.
  • Page 23 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Figure 2-6. Next possible completions: Show Command In the above example, all of the possible next parameters for the show command are displayed. At the next command prompt, the up arrow was used to re-enter the show command, followed by the account parameter.

  • Page 24: Command Syntax

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide OMMAND The following symbols are used to describe how command entries are made and values and arguments are specified in this manual. The online help contained in the CLI and available through the console interface uses the same syntax.

  • Page 25: Vertical Bar

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide [square brackets] Purpose Encloses a required value or set of required arguments. arguments can be specified. create account [admin|user] Syntax Description In the above syntax example, you must specify either an admin or a user level account to be created.
  • Page 26 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide {braces} Purpose Encloses an optional value or set of optional arguments. config serial_port Syntax {baud_rate[9600|19200|38400|115200] | auto_logout [never|2_minutes|5_minutes| 10_minutes|15_minutes]} Description In the above syntax example, baud_rate, auto_logout, never, 2_minutes, 5_minutes, 10_minutes, and 15_minutes are all optional arguments.
  • Page 27 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Line Editing Key Usage Shifts the cursor to the next field to the left. Multiple Page Display Control Keys Space Displays the next page. CTRL+c Stops the display of remaining pages when multiple pages are to be displayed.

  • Page 28: Basic Switch Commands

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide ASIC The basic switch commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters create account [admin|user] <username> config account <username> show account...

  • Page 29: Command Parameters

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Command Parameters disable web save reboot reset {config|system} login logout Each command is listed, in detail, in the following sections. create account Purpose Used to create user accounts create account [admin|user] <username>...
  • Page 30 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide create account characters. Example Usage: To create an administrator-level user account with the username “dlink”. local>create account admin dlink Command: create account admin dlink Enter a case-sensitive new password:**** Enter the new password again for confirmation:**** Success.
  • Page 31 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config account characters. Passwords characters. Example Usage: To configure the user password of “dlink” account: local>config account dlink Command: config account dlink Enter a old password:**** Enter a case-sensitive new password:**** Enter the new password again for confirmation:**** Success.
  • Page 32 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Example Usage: To display the accounts which have been created: local>show account Command: show account Current Accounts: Username Access Level --------------- ------------ dlink Admin local> delete account Purpose Used to delete an existing user account delete account <username>...
  • Page 33 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Success. local> show session Purpose Used to display a list of currently logged-in users. Syntax show session Description This command displays a list of all the users that are logged-in at the time the command is issued.
  • Page 34 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show switch Purpose Used to display information about the switch. Syntax show switch Description This command displays information about the switch. Parameters none. Restrictions none. Example Usage: To display the switch information: local>show switch...
  • Page 35 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide System Contact Spanning Tree : Disabled GVRP : Disabled IGMP Snooping : Disabled : Disabled DVMRP : Disabled PIM-DM : Disabled OSPF : Disabled TELNET : Enabled (TCP 23) SNTP : Disabled local>...
  • Page 36 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Parity Bits : None Stop Bits Auto-Logout : 10 mins local>...
  • Page 37 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config serial_port Purpose Used to configure the serial port. config serial_port Syntax {baud_rate[9600|19200|38400|115200]|auto _logout [never|2_minutes|5_minutes|10_minutes| 15_minutes]} Description This command is used to configure the serial port’s baud rate and auto logout settings.
  • Page 38 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Example Usage: To configure baud rate: local>config serial_port baud_rate 9600 Command: config serial_port baud_rate 9600 Success. local> enable clipaging Purpose Used to pause the scrolling of the console screen when the show command displays more than one page.
  • Page 39 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide To enable pausing of the screen display when show command output reaches the end of the page: local>enable clipaging Command: enable clipaging Success. local> disable clipaging Purpose Used to disable the pausing of the console...
  • Page 40 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local>disable clipaging Command: disable clipaging Success. local> enable telnet Purpose Used to enable communication with and management of the switch using the Telnet protocol. Syntax enable telnet 65535> Description This command is used to enable the Telnet protocol on the switch.
  • Page 41 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Command: enable telnet 23 Success. local> disable telnet Purpose Used to disable the Telnet protocol on the switch. disable telnet Syntax Description This command is used to disable the Telnet protocol on the switch.
  • Page 42 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide enable web Purpose Used management software on the switch. Syntax enable web <tcp_port_number 1-65535> Description This command is used to enable the Web- based management software on the switch. The user can specify the TCP port number the switch will use to listen for Telnet requests.
  • Page 43 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide disable web Purpose Used management software on the switch. Syntax disable web Description This command disables the Web-based management software on the switch. Parameters none. Restrictions Only administrator-level users can issue this command.
  • Page 44 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide save The saved switch configuration will be loaded into the switch’s memory each time the switch is restarted. Parameters none. Restrictions Only administrator-level users can issue this command. Example Usage: To save the switch’s current configuration to non-volatile RAM: local>save...
  • Page 45 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Example Usage: To restart the switch: local>reboot Command: reboot Are you sure want to proceed with the system reboot? (y|n) Please wait, the switch is rebooting... reset Purpose Used to reset the switch to the factory default settings.
  • Page 46 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide reset Restrictions Only administrator-level users can issue this command. Example Usage: To restore all of the switch’s parameters to their default values: local>reset config Command: reset config Success. local> login Purpose Used to log in a user to the switch’s console.
  • Page 47 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide To initiate the login procedure: local>login Command: login UserName: logout Purpose Used to log out a user from the switch’s console. logout Syntax Description This command terminates the current user’s session on the switch’s console.

  • Page 48: Switch Port Commands

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide The switch port commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters config ports <portlist|all> speed [auto|10_half|10_full|100_half|100_full| 1000_half|1000_full] state [enabled|disabled] show ports <portlist|all>...
  • Page 49 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config ports [auto|10_half|10_full|100_half|100_full| 1000_half|1000_full] state [enabled|disabled]} Description This command allows for the configuration of the switch’s Ethernet ports. Only the ports listed in the <portlist> will be affected. all − Displays all ports on the switch to be Parameters configured.
  • Page 50 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Example Usage: To configure the speed of port 3 to be 10 Mbps, full duplex, learning and state enabled: local>config ports 1-3 speed 10_full state enabled Command: config ports 1-3 speed 10_full state enabled Success.
  • Page 51 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Example Usage: To display the configuration of the ports 1-7: local>show ports 1-7 Command: show ports 1-7 Port Port Settings State Speed|Duplex ---- -------- --------------------- Enabled Auto Enabled Auto Enabled Auto Enabled...

  • Page 52: Network Management Commands

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide ETWORK The network management commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters create snmp <community_string 32> community view <view_name 32>...
  • Page 53 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Command Parameters <oid> view_type [included|excluded] delete snmp view <view_name 32> [all|<oid>] show snmp view {<view_name 32>} config snmp <snmp_engineID> engineID show snmp engineID create snmp <groupname 32> [v1|v2c|v3 group [noauth_nopriv| auth_nopriv|auth_priv]] {read_view <view_name 32> |write_view <view_name 32>...
  • Page 54 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Command Parameters disable snmp authenticate traps create <ipaddr> trusted_host show <ipaddr> trusted_host delete <ipaddr> trusted_host show snmp community {<community_string 32>} engine ID groups host <ipaddr> user view ping <ipaddr> times <value 1-255>...
  • Page 55 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide create snmp community [read_only|read_write] Description This command is used to create an SNMP community string and to specify the string enabling privileges for the SNMP management host. Parameters <community_string 32> − An alphanumeric...
  • Page 56 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide To create a read-write level SNMP community “dlink”: local>create snmp community dlink view CommunityView read_write Command: create snmp community dlink view CommunityView read_write Success. local> delete snmp community Purpose Used to delete an SNMP community string previously entered on the switch.
  • Page 57 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local>delete snmp community dlink Command: delete snmp community dlink Success. local> create snmp user Purpose Used to create a new SNMP user to an SNMP group that is also created by this command.
  • Page 58 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide create snmp user appears in encrypted format. by_password − Indicates input password for authentication and privacy. by_key − Indicates input key for authentication and privacy. auth [md5|sha] – Initiate an authentication-level setting session.
  • Page 59 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local>create snmp user dlink D-Link_group encrypted by_password auth md5 12345678 priv des 12345678 Command: create snmp user dlink D-Link_group encrypted by_password auth md5 12345678 priv des 12345678 Success. local> delete snmp user...
  • Page 60 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local>delete snmp user dlink Command: delete snmp user dlink Success. local> create snmp view Purpose Used to assign views to community strings to limit which MIB objects an SNMP manager can access.
  • Page 61 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Example Usage: To create an SNMP view: local>create snmp view dlinkview 1.3.6 view_type included Command: create snmp view dlinkview 1.3.6 view_type included Success. local> delete snmp view Purpose Used to remove a view record.
  • Page 62 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide To delete an SNMP view: local>delete snmp view dlinkview all Command: delete snmp view dlinkview all Success. local> show snmp view Purpose Used to display the SNMP view record. show snmp view {<view_name 32>}...
  • Page 63 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide restricted 1.3.6.1.2.1.1 restricted 1.3.6.1.2.1.11 restricted 1.3.6.1.6.3.10.2.1 restricted 1.3.6.1.6.3.11.2.1 restricted 1.3.6.1.6.3.15.1.1 CommunityView CommunityView 1.3.6.1.6.3. CommunityView 1.3.6.1.6.3.1 Total Entries: 8 local> local> config snmp engineID Purpose Used to configure an identifier for the SNMP engine on the switch.
  • Page 64 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide To configure an SNMP engine on the switch: local>config snmp engineID 1023457890 Command: config snmp engineID 1023457890 Success. local> show snmp engineID Purpose Used to display the identification of the SNMP engine on the switch.
  • Page 65 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide To display an SNMP engine on the switch: local>show snmp engineID Command: show snmp engineID SNMP Engine ID : 1023457890 local> create snmp group Purpose Used to create a new SNMP group, or a table that maps SNMP users to SNMP views.
  • Page 66 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide create snmp group auth_nopriv − Specifies support for packet authentication. auth_priv − Specifies support for packet authentication and encrypting. <view_name 32> − View name, the MIB view. Restrictions Only administrator-level users can issue this command.
  • Page 67 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide delete snmp group an SNMP group. <groupname 32> − An alphanumeric name Parameters of up to 32 characters that will identify the SNMP group that will be deleted. Restrictions Only administrator-level users can issue this command.
  • Page 68 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide create snmp host v1 − The least secure of the possible security models. v2c − The second least secure of the possible security models. v3 − The most secure of the possible security models.
  • Page 69 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide delete snmp host Purpose Used to delete a recipient of an SNMP trap operation. Syntax delete snmp host <ipaddr> Description The delete snmp host command deletes a recipient of an SNMP trap operation.
  • Page 70 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show snmp host Description This show snmp host command displays the recipient for which the traps are targeted. Parameters <ipaddr> – The IP address of the recipient for which the traps are targeted. If no parameter is specified, all SNMP hosts will be displayed.
  • Page 71 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide enable rmon Syntax enable rmon Description This command is used, in conjunction with the disable RMON command below, to enable and disable remote monitoring (RMON) on the switch. Parameters none. Restrictions Only administrator-level users can issue this command.
  • Page 72 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide disable rmon Parameters none. Restrictions Only administrator-level users can issue this command. Example Usage: To disable RMON: local>disable rmon Command: disable rmon Success. local> config snmp system_contact Purpose Used to enter the name of a contact person who is responsible for the switch.
  • Page 73 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config snmp system_contact person who is responsible for the switch. Restrictions Only administrator-level users can issue this command. Example Usage: To configure the switch contact to “ctsnow”: local>config snmp system_contact ctsnow Command: config snmp system_contact ctsnow Success.
  • Page 74 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config snmp system_location this command. Example Usage: To configure the switch location for “Rota”: local>config snmp system_location Rota Command: config snmp system_location Rota Success. local> config snmp system_name Purpose Used to configure a name for the switch.
  • Page 75 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local>config snmp system_name DES3350 Command: config snmp system_name DES3350 Success. local> enable snmp traps Purpose Used to enable SNMP trap support. enable snmp traps Syntax Description This command is used to enable SNMP trap support on the switch.
  • Page 76 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide disable snmp traps Purpose Used to disable SNMP trap support on the switch. Syntax enable snmp traps Description This command is used to disable SNMP trap support on the switch. Parameters none.
  • Page 77 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide enable snmp authenticate traps Description This command is used to enable SNMP authentication trap support on the switch. Parameters none. Restrictions Only administrator-level users can issue this command. Example Usage: To turn on SNMP authentication trap support: local>enable snmp authenticate traps...
  • Page 78 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide disable snmp authenticate traps this command. Example Usage: To turn off SNMP authentication trap support: local>disable snmp authenticate traps Command: disable snmp authenticate traps Success. local> create trusted_host Purpose Used to create trusted hosts.
  • Page 79 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Example Usage: To create a trusted host: local>create trusted_host Command: create trusted_host 10.1.1.1 Success. local> show trusted_host Purpose Used to display a list of trusted hosts entered on the switch using the create trusted_host command above.
  • Page 80 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Management Stations IP Address: ------------------------- 10.1.1.1 Total Entries: 1 local> delete trusted_host Purpose Used to delete a trusted host entry made using the create trusted_host command above. delete trusted _host <ipaddr> Syntax...
  • Page 81 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local> show snmp Purpose Used configuration information entered on the switch. Syntax show snmp [community <community_string 32>|engineID|groups|host <ipaddr>|user|view] Description This command will display the current SNMP configuration on the switch. Parameters community − This command is used to display SNMP community strings that are configured on the switch.
  • Page 82 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show snmp also displayed. host − This command is used to display the IP addresses and configuration information remote designated as recipients of SNMP traps that are generated by the switch’s SNMP agent.
  • Page 83 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Community Name ----------------------------------- -------------------------- private CommunityView public CommunityView Total Entries: 1 local> ping Purpose Used to test the connectivity between network devices. ping <ipaddr> {times <value 1-255>} Syntax {timeout <sec 1-99>} Description...
  • Page 84 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide ping timeout <sec 1-99> − Defines the time-out period while waiting for a response from the remote device. A value of 1 to 99 seconds can be specified. The default is 1 second.
  • Page 85 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide traceroute Description This command allows you to trace a route between the switch and a given host on the network. Parameters <ipaddr> − The IP address of the remote device. ttl <value> − The time to live value of the trace route request.
  • Page 86 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide 1 <10 ms. 10.48.74.121 local> show ipfdb Purpose Used to show the IP forwarding database. Syntax show ipfdb {<ipaddr>} Description This command allows you to display the IP forwarding database. Parameters <ipaddr> − The IP address of the forwarding database.
  • Page 87 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide System 10.1.1.101 System 10.1.1.102 System 10.1.1.151 System 10.1.1.154 local> Dynamic Dynamic Dynamic Dynamic...

  • Page 88: Download/Upload Commands

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide OWNLOAD The download|upload commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters download firmware <ipaddr> <path_filename 127> configuration <ipaddr> <path_filename 127>...
  • Page 89 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide download Purpose Used to download and install new firmware or a switch configuration file from a TFTP server. download [ firmware <ipaddr> Syntax <path_filename 127> |configuration <ipaddr> <path_filename 127> {increment}] Description This command is used to download a new firmware or a switch configuration file from a TFTP server.
  • Page 90 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide download level users can issue this command. Example Usage: local>download configuration 10.48.74.121 c:\cfg\setting.txt Command: download configuration 10.48.74.121 c:\cfg\setting.txt Connecting to server... Done. Download configuration... Done. local> upload Purpose Used to upload the current switch settings or the switch history log to a TFTP server.
  • Page 91 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide upload <ipaddr> − The IP address of the TFTP server. The TFTP server must be on the same IP subnet as the switch. <path_filename location of the switch configuration file on the TFTP server. This file will be replaced by the uploaded file from the switch.

  • Page 92: Network Monitoring Commands

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide ETWORK The network monitoring commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters show packet ports <portlist> show error ports <portlist>...
  • Page 93 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show packet ports sent and received by the switch. Syntax show packet ports <portlist> Description This command is used to display statistics about packets sent and received by ports specified in the port list.
  • Page 94 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide 512-1023 1024-1518 Unicast RX Multicast RX Broadcast RX 3686 CTRL+C ESC q Quit SPACE n Next Page show error ports Purpose Used to display the error statistics for a range of ports.
  • Page 95 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Command: show error ports 3 Port number : 3 RX Frames --------------- CRC Error Excessive Deferral Undersize CRC Error Oversize Late Collision Fragment Excessive Collision Jabber Single Collision Drop Pkts Collision CTRL+C ESC q...
  • Page 96 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Port TX|sec RX|sec Util ---- ---------- ---------- ---- CTRL+C ESC q Quit SPACE n Next Page clear counters Purpose Used clear counters. clear counters {ports <portlist>} Syntax Description This command will clear the counters used by the switch to compile statistics.
  • Page 97 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide clear counters separated by a dash. For example, 3 would specify port 3. 4 specifies port 4. 3-4 specifies all of the ports between port 3 and port 4 − in numerical order..
  • Page 98 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Example Usage: To clear the log information: local>clear log Command: clear log Success. local> show log Purpose Used to display the switch history log. show log {index <value>} Syntax Description This command will display the contents of the switch’s history log.
  • Page 99 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Anonymous) 000d00h49m Successful login through Console (Username: Anonymous) 000d00h49m Logout through Console (Username: Anonymous) local>...

  • Page 100: Spanning Tree Commands

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide PANNING The spanning tree commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters config stp ports <portlist> cost auto <value 1-200000000>...
  • Page 101 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Command Parameters show stp show stp ports <portlist> Each command is listed, in detail, in the following sections. config stp ports Purpose Used to set up STP on the port level. config stp ports <portlist> {cost Syntax [auto|<value 1-200000000>]|priority...
  • Page 102 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config stp ports sub-commands listed below. cost <value> − This defines a metric that indicates the relative cost of forwarding packets to the specified port list. The default cost for a 1000 Mbps port is...
  • Page 103 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config stp ports edge [true|false] – true designates the port as an edge port. Edge ports cannot create loops, however an edge port can lose edge port status if a topology change creates a potential for a loop.
  • Page 104 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config stp Purpose Used to set up STP on the switch level. config stp {maxage <value 6- Syntax 40>|hellotime <value 1-10>forwarddelay <value 4-30>|priority <value 0- 61440>|version [rstp|stp]|txholdcount <value 1-10>|fbpdu [enabled|disabled]} Description This command is used to set up the Spanning Tree Protocol (STP) on the switch level.
  • Page 105 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config stp the priority. The default is 32,768. version [rstp|stp] – Select the Spanning Tree Protocol version used for the switch. For IEEE 802.1d STP select STP. Select RSTP for IEEE 802.1w Rapid STP.
  • Page 106 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide enable stp Syntax enable stp Description This command allows the Spanning Tree Protocol to be globally enabled on the switch. Parameters none. Restrictions Only administrator-level users can issue this command. Example Usage: To enable STP on the switch: local>enable stp...
  • Page 107 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide disable stp Parameters none. Restrictions Only administrator-level users can issue this command. Example Usage: To disable STP on the switch: local>disable stp Command: disable stp Success. local> show stp Purpose Used to display the switch’s current STP configuration.
  • Page 108 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Status 1: STP enabled: local>show stp Command: show stp STP Status : Enabled Max Age : 20 Hello Time Forward Delay : 15 Priority : 32768 STP Version : STP compatible TX Hold Count...
  • Page 109 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Priority : 32768 STP Version : STP compatible TX Hold Count Forwarding BPDU : Enabled local> show stp ports Purpose Used to display the switch’s current per- port group STP configuration. show stp ports <portlist>...
  • Page 110 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Port Designated Bridge State Cost Pri Edge P2P Status ---- -------------------------- -------- ------ ----- ----- Yes *200000 128 No Yes *200000 128 No Yes *200000 128 No Yes *200000 128 No Yes *200000 128 No...

  • Page 111: Forwarding Database Commands

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide ORWARDING The forwarding database commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters create fdb <vlan_name 32> <macaddr> port <port> create <vlan_name 32>...
  • Page 112 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Command Parameters aging_time show fdb port <port> vlan <vlan_name 32> mac_address <macaddr> static aging_time Each command is listed, in detail, in the following sections. create fdb Purpose Used to create a static entry to the unicast...
  • Page 113 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide create fdb Restrictions Only administrator-level users can issue this command. Example Usage: To create an unicast MAC forwarding: local>create fdb default 00-00-00-00-01-02 port 5 Command: create fdb default 00-00-00-00-01-02 port 5 Success.
  • Page 114 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide create multicast_fdb Restrictions Only administrator-level users can issue this command. Example Usage: To create multicast MAC forwarding: local>create multicast_fdb default 01-00-5E-00-00-00 Command: create multicast_fdb default 01-00-5E-00-00- Success. local> config multicast_fdb Purpose Used to configure the switch’s multicast MAC address forwarding database.
  • Page 115 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config multicast_fdb address to the forwarding table, delete will remove forwarding table. <portlist> − Specifies a range of ports to be configured. The port list is specified by listing the beginning port number and the highest port number of the range.
  • Page 116 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide delete fdb Purpose Used to delete an entry to the switch’s forwarding database. Syntax delete fdb <vlan_name 32> <macaddr> Description This command is used to delete a previous entry forwarding database. Parameters <vlan_name 32>...
  • Page 117 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide clear fdb addresses. You can enter a VLAN name and MAC address to delete a specific entry, skip the MAC address parameter and delete all the entries belonging to a specified VLAN.
  • Page 118 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local>clear fdb all Command: clear fdb all Success. local> show multicast_fdb Purpose Used to display the contents of the switch’s multicast forwarding database. show multicast_fdb [vlan <vlan_name Syntax 32>|mac_address <macaddr> Description This command is used to display the current contents of the switch’s multicast...
  • Page 119 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide MAC Address : 01-00-5E-00-00-00 Egress Ports : 1-5, 26 Mode : Static Total Entries local> config fdb aging_time Purpose Used to set the aging time of the forwarding database. Syntax config fdb aging_time <sec>...
  • Page 120 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config fdb aging_time Parameters <sec> − The aging time for the MAC address forwarding database value. Restrictions Only administrator-level users can issue this command. Example Usage: To set the fdb aging time: Local>config fdb aging_time 25...
  • Page 121 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show fdb will always forward traffic to the specified device through this port. <vlan_name 32> − The name of the VLAN on which the MAC address resides. <macaddr> − The MAC address that will be added to the forwarding table.
  • Page 122 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local>...

  • Page 123: Broadcast Storm Control Commands

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide ROADCAST ONTROL The broadcast storm control commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters config traffic <storm_grouplist 1-8> control broadcast [enabled|disabled]...
  • Page 124 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config traffic control Syntax config traffic control [<storm_grouplist 1-8>|all] [enabled|disabled]|multicast [enabled|disabled]|dlf [enabled|disabled]|threshold <value 0- 255> Description This command broadcast storm control. <storm_grouplist 1-8> − Used to specify a Parameters broadcast storm control group.
  • Page 125 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Example Usage: To configure traffic control and state: local>config traffic control 1-3,1-2 broadcast enabled Command: config traffic control 1-3 broadcast enabled Success. local> show traffic control Purpose Used to display current traffic control settings.
  • Page 126 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Command: show traffic control Traffic Control Broadcast Multicast Destination Group [ports] Threshold Storm ------ ------------- --------- --------- 1 [ 1 - 8 ] Enabled Disabled 2 [ 9 - 16] Enabled Disabled...

  • Page 127: Qos Commands

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide QOS C The MAC address priority commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters config scheduling <class_id 0-3> {max_packet <value 0-255>| max_latency <value 0-255>}...
  • Page 128 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Command Parameters config <portlist> bandwidth_control rx_rate [no_limit| <value 1-1000>] tx_rate [no_limit| <value 1-1000>] show <portlist> bandwidth_control Each command is listed, in detail, in the following sections. config scheduling Purpose Used to configure the traffic scheduling mechanism for each COS queue.
  • Page 129 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config scheduling max_packet and max_latency parameters are set to 0) is to empty the four hardware priority queues in order − from the highest priority queue (hardware queue 3) to the lowest priority queue (hardware queue 0).
  • Page 130 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config scheduling specified. This number is then multiplied by 16 ms to determine the maximum latency. For example, if 3 is specified, the maximum latency allowed will be 3 X 16 = 48 ms.
  • Page 131 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config scheduling the total allowed time for the queue to transmit packets. For example, a value of 3 specifies 3 X 16 = 48 ms. The queue will continue transmitting the last packet until it is finished when the max_latency timer expires.
  • Page 132 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show scheduling switch. Parameters none. Restrictions none. Example Usage: Local> show scheduling Command: show scheduling QOS Output Scheduling MAX. Packets MAX. Latency ------------------- ------------------ Class-0 Class-1 Class-2 Class-3 local> config 802.1p user_priority Purpose Used to map the 802.1p user priority of an...
  • Page 133 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config 802.1p user_priority Description This command allows you to configure the way the switch will map an incoming packet, based on its 802.1p user priority, to one of the four available hardware priority queues on the switch.
  • Page 134 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config 802.1p user_priority <priority 0-7> − The 802.1p user priority you want to associate with the <class_id 0- 3> (the number of the hardware queue) with. <class_id 0-3> − The number of the switch’s hardware priority queue.
  • Page 135 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show 802.1p user_priority Description This command will display the current 802.1p user priority to hardware priority queue mapping in use by the switch. Parameters None. Restrictions None. Example Usage: local> show 802.1p user_priority Command: show 802.1p user_priority...
  • Page 136 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config 802.1p default_priority settings on the switch. If an untagged packet is received by the switch, the priority configured with this command will be written to the packet’s priority field. Syntax config 802.1p default_priority [<portlist>|all] <priority 0-7>...
  • Page 137 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Example Usage: local> config 802.1p default_priority all 5 Command: config 802.1p default_priority all 5 Success. local> show 802.1p default_priority Purpose Used to display the current default priority settings on the switch. show 802.1p...
  • Page 138 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show 802.1p default_priority specifies all of the ports between port 3 and port 4 − in numerical order. Restrictions None. Example Usage: local> show 802.1p default_priority all Command: show 802.1p default_priority all...
  • Page 139 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config traffic_segmentation Purpose Used to configure traffic segmentation on the switch. config traffic_segmentation <portlist> Syntax forward_list [null|<portlist>] Description The config traffic_segmentation command is used to configure traffic segmentation on the switch. Parameters <portlist>...
  • Page 140 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config traffic_segmentation the highest port number of the range. The beginning and end of the port list range are separated by a dash. For example, 3 would specify port 3. 4 specifies port 4. 3-4 specifies all of the ports between port 3 and port 4 −...
  • Page 141 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show traffic_segmentation segmentation configuration on the switch. Parameters <portlist> − Specifies a range of ports for which current configuration displayed. The port list is specified by listing the beginning port number and the highest port number of the range.
  • Page 142 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide 9-15 9-15 9-15 9-15 1-26 1-26 1-26 1-26 1-26 1-26 1-26 1-26 CTRL+C ESC q Quit SPACE n Next Page config bandwidth_control Purpose Used to configure bandwidth control on a by-port basis.
  • Page 143 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config bandwidth_control rx_rate − Specifies that one of the parameters below (no_limit or <value 1- 1000>) will be applied to the rate at which the above specified ports will be allowed to receive packets no_limit −...
  • Page 144 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local>config bandwidth_control 1-10 tx_rate 10 Command: config bandwidth_control 1-10 tx_rate 10 Success. local> show bandwidth_control Purpose Used to display the bandwidth control configuration on the switch. show bandwidth_control {<portlist>} Syntax Description The show bandwidth_control command...
  • Page 145 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local>show bandwidth_control 1-11 Command: show bandwidth_control 1-11 Bandwidth Control Table Port RX Rate (Mbit|sec) TX_RATE (Mbit|sec) ---- ------------------------ ---------------------- no_limit no_limit no_limit no_limit no_limit no_limit no_limit no_limit no_limit no_limit no_limit no_limit local>...

  • Page 146: Port Mirroring Commands

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide The port mirroring commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters config mirror port <port> [add|delete] source ports <portlist> [rx|tx|both]...
  • Page 147 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config mirror port Used to configure a mirror port − source Purpose port pair on the switch. Syntax config mirror port <port> [add|delete] source ports <portlist> [rx|tx|both] Description This command allows you to add or delete mirroring ports.
  • Page 148 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config mirror port port list. both − Mirrors all the packets received or sent by the port or ports in the port list. Restrictions Only administrator-level users can issue this command. Example Usage: To add the mirroring ports: local>...
  • Page 149 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide enable mirror Parameters none. Restrictions none. Example Usage: To enable mirroring configurations: local>enable mirror Command: enable mirror Success. local> disable mirror Purpose Used to disable a previously entered port mirroring configuration. Syntax...
  • Page 150 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Example Usage: To disable mirroring configurations: local>disable mirror Command: disable mirror Success. local> show mirror Purpose Used to show the current port mirroring configuration on the switch. show mirror Syntax Description This command displays the current port mirroring configuration on the switch.
  • Page 151 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local>show mirror Command: show mirror Current Settings Mirror Status: Enabled Target Port : 9 Mirrored Port TX: 1-5 local>...

  • Page 152: Vlan Commands

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide VLAN C The VLAN commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters create vlan <vlan_name 32> tag <vlanid> advertisement delete vlan <vlan_name 32>...
  • Page 153 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Command Parameters show vlan <vlan_name 32> show gvrp <portlist> Each command is listed, in detail, in the following sections. create vlan Purpose Used to create a VLAN on the switch. Syntax create vlan <vlan_name 32> {tag <vlanid>|advertisement}...
  • Page 154 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Example Usage: To create a VLAN v1, tag 2: local>create vlan v1 tag 2 Command: create vlan v1 tag 2 Success. local> delete vlan Purpose Used to delete a previously configured VLAN on the switch.
  • Page 155 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Success. local> config vlan add Purpose Used to add additional ports to a previously configured VLAN. config vlan <vlan_name 32> add Syntax [tagged|untagged|forbidden] <portlist> Description This command allows you to add ports to the port list of a previously configured VLAN.
  • Page 156 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config vlan add of the ports between port 3 and port 4 − in numerical order. Restrictions Only administrator-level users can issue this command. Example Usage: To add 4 through 8 as tagged ports to the VLAN v1: local>config vlan v1 add tagged 4-8...
  • Page 157 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config vlan delete <portlist> − A range of ports you want to delete from the above specified VLAN. The port list is specified by listing the beginning port number and the highest port number of the range.
  • Page 158 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config vlan advertisement Description This command is used to enable or disable GVRP on the specified VLAN. Parameters <vlan_name 32> − The name of the VLAN on which you want to enable or disable GVRP.
  • Page 159 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config gvrp Syntax config gvrp [<portlist>|all] {state [enabled|disabled]|ingress_checking [enabled|disabled] } Description This command is used to configure the Group VLAN Registration Protocol on the switch. You can configure ingress checking and the sending and receiving of GVRP information.
  • Page 160 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Example Usage: To set the ingress checking status and the sending and receiving GVRP information: local>config gvrp 1-5 state enabled ingress_checking enabled Command: config gvrp 1-5 state enabled ingress_checking enabled Success. enable gvrp Purpose Used to enable GVRP on the switch.
  • Page 161 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Success. local> disable gvrp Purpose Used to disable GVRP on the switch. disable gvrp Syntax Description This command, along with disable gvrp below, is used to enable and disable GVRP on the switch − without changing the GVRP configuration on the switch.
  • Page 162 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show vlan Purpose Used display configuration on the switch Syntax show vlan {<vlan_name 32>} Description This command information about each VLAN including the VLAN Tagging|Untagging Member|Non-member|Forbidden status of each port that is a member of the VLAN.
  • Page 163 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local> show gvrp Purpose Used to display the GVRP status for a port list on the switch. Syntax show gvrp {<portlist>} Description This command displays the GVRP status for a port list on the switch, including the PVID.
  • Page 164 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show gvrp port number of the range. The beginning and end of the port list range are separated by a dash. For example, 3 would specify port 3. 4 specifies port 4. 3-4 specifies all of the ports between port 3 and port 4 −...
  • Page 165 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled CTRL+C ESC q Quit SPACE n Next Page Enter Next Entry...

  • Page 166: Link Aggregation Commands

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide GGREGATION The link aggregation commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters create group_id <group_id 1-6> {type [lacp|static]} link_aggregation delete group_id <group_id 1-6>...
  • Page 167 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Command Parameters show {group_id <group_id 1-6>| link_aggregation algorithm} show lacp_port <portlist> Each command is listed, in detail, in the following sections. create link_aggregation group_id Purpose Used to create a link aggregation group on the switch.
  • Page 168 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local>create link_aggregation group_id 1 Command: create link_aggregation group_id 1 Success. local> delete link_aggregation group_id Purpose Used to delete a previously configured link aggregation group. delete link_aggregation Syntax <group_id 1-6> Description This command previously group.
  • Page 169 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local> config link_aggregation Purpose Used to configure a previously created link aggregation group. Syntax config link_aggregation group_id <group_id 1-6> {master_port <port>|ports <portlist>| state [enabled|disabled]} Description This command allows you to configure a...
  • Page 170 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config link_aggregation numerical order. state [enabled|disabled] − Allows you to enable aggregation group. Restrictions Only administrator-level users can issue this command. Example Usage: To define a load-sharing group of ports, group-id 1, master port 17: local>config link_aggregation group_id 1 master_port 7 ports 5-10...
  • Page 171 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config link_aggregation algorithm Description This command configures to part of the packet examined by the switch when selecting the egress port for transmitting load-sharing data. This feature is only available using the address- based load-sharing algorithm.
  • Page 172 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local>config link_aggregation algorithm mac_source_dest Command: config link_aggregation algorithm mac_source_dest Success. local> config lacp_port Purpose Used to configure the current mode of the Link Aggregation Control Protocol port. Syntax config lacp_port <portlist> mode...
  • Page 173 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Success. local> show link_aggregation Purpose Used aggregation configuration on the switch. show link_aggregation {group_id Syntax <group_id 1-6>|algorithm} Description This command will display the current link aggregation configuration of the switch. Parameters <group_id 1-6> − Specifies the group id.
  • Page 174 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Group ID Type : TRUNK Master Port Member Port : Active Port Status : Disabled Flooding Port : 0 local> show lacp_port Purpose Used to show the current mode of the Link Aggregation Control Protocol port.
  • Page 175 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Active Active Active Active Active Active Active Active Active Active Active Active Passive Passive Passive Passive Passive Passive CTRL+C ESC q Quit SPACE n Next Page Enter Next Entry...

  • Page 176: Ip Interface Commands

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide IP I The IP interface commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters config ipif <ipif_name 12> vlan <vlan_name 32>...
  • Page 177 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Command Parameters show ipif <ipif_name 12> Each command is listed, in detail, in the following sections. config ipif Purpose Used to configure an IP interface created with the create ipif command. config ipif <ipif_name 12> [{ipaddress Syntax <network_address>|vlan <vlan_name...
  • Page 178 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config ipif protocol for the assignment of an IP address to the switch’s System IP interface. dhcp − Allows the selection of the DHCP protocol for the assignment of an IP address to the switch’s System IP interface.
  • Page 179 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide create ipif Parameters <ipif_name 12> – The name of the IP interface can be up to 12 alphaneumeric characters. <network_address> netmask of the IP interface to be created. You can specify the address and mask information using the traditional format (for example, 10.1.2.3/255.0.0.0 or in...
  • Page 180 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide delete ipif Purpose Used to delete an IP interface on the switch. Syntax delete ipif {<ipif_name 12> | all} Description This command will delete an IP interface on the switch. Parameters <ipif_name 12> – The name of the IP interface can be up to 12 alphaneumeric characters.
  • Page 181 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide enable ipif Syntax enable ipif {<ipif_name 12> | all} Description This command will enable an IP interface on the switch. Parameters <ipif_name 12> – The name of the IP interface can be up to 12 alphaneumeric characters.
  • Page 182 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide disable ipif Description This command will disable an IP interface on the switch. Parameters <ipif_name 12> – The name of the IP interface can be up to 12 alphaneumeric characters. all − Specifies all IP interface names on the switch.
  • Page 183 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show ipif switch. Parameters <ipif_name 12> – The name of the IP interface can be up to 12 alphaneumeric characters. Restrictions none. Example Usage: To display IP interface settings: local>show ipif Command: show ipif...

  • Page 184: Arp Commands

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide ARP C The ARP commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters create arpentry <ipaddr> <macaddr> delete arpentry <ipaddr> config arp_aging time <value 0-65535>...
  • Page 185 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide create arpentry Purpose Used to make a static entry into the ARP table. Syntax create arpentry <ipaddr> <macaddr> Description This command is used to enter an IP address into the switch’s ARP table.
  • Page 186 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide delete arpentry Purpose Used to delete a static entry into the ARP table. delete arpentry {<ipaddr>|all} Syntax Description This command is used to delete a static ARP entry, made using the create arpentry command above, by specifying either the IP address of the entry or all.
  • Page 187 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config arp_aging Purpose Used to configure the age-out timer for ARP table entries on the switch. Syntax config arp_aging time <value 0-65535> Description This command sets the maximum amount of time, in seconds, that an ARP entry can remain in the switch’s ARP table, without...
  • Page 188 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config arpentry config arpentry <ipaddr> <macaddr> Syntax Description This command configures ARP entries in the switch’s ARP table. <ipaddr> − The IP address of the end node Parameters or station. <macaddr> corresponding to the IP address above.
  • Page 189 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show arpentry Description This command is used to display the current contents of the switch’s ARP table. Parameters <ipif_name 12> − The name of the IP interface the end node or station for which the ARP table entry was made, resides on.
  • Page 190 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide System 10.14.82.24 00-50-BA-90-37-10 System 10.15.1.60 00-80-C8-17-42-55 System 10.17.42.153 00-80-C8-4D-4E-0A System 10.19.72.100 00-50-BA-38-7D-5E System 10.21.32.203 00-80-C8-40-C1-06 System 10.40.44.60 00-50-BA-6B-2A-1E System 10.42.73.221 00-01-02-03-04-00 System 10.44.67.1 00-50-BA-DA-02-51 System 10.47.65.25 00-50-BA-DA-03-2B System 10.50.8.7 00-E0-18-45-C7-28 System 10.90.90.90...
  • Page 191 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide To remove dynamic entries in the ARP table: local>clear arptable Command: clear arptable Success. local>...

  • Page 192: Routing Table Commands

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide OUTING The routing table commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters create iproute default <network_address> <ipaddr> <metric 1-65535> delete iproute default <network_address>...
  • Page 193 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide create iproute Purpose Used to create an IP route entry to the switch’s IP routing table. Syntax create iproute [default | <network_address>]<ipaddr> {<metric 1- 65535>} Description This command is used to create an IP route entry to the switch’s IP routing table.
  • Page 194 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Success. local> delete iproute Purpose Used to delete an IP route entry from the switch’s IP routing table. Syntax delete iproute [default|<network_address>] Description This command will delete an existing entry from the switch’s IP routing table.
  • Page 195 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Command: delete iproute default Success. local> show iproute Purpose Used to display the switch’s current IP routing table. show iproute {<network_address>} Syntax {static|rip|ospf} Description This command will display the switch’s current IP routing table.
  • Page 196 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Restrictions None. Example Usage: To display the contents of the IP routing table: local>show iproute Command: show iproute Routing Table IP Address|Netmask Gateway ---------------------------- --------------- --------------- 10.0.0.0|8 0.0.0.0 Total Entries : 1...

  • Page 197: Route Redistribution Commands

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide OUTE EDISTRIBUTION The switch port commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters create route src [static|rip|local] redistribute dst mettype [1|2] ospf metric <value>...
  • Page 198 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Each command is listed, in detail, in the following sections. create route redistribute dst ospf Purpose Used to add route redistribution settings for the exchange of RIP routes to OSPF routes on the switch.
  • Page 199 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide create route redistribute dst ospf <value> − Allows the entry of an OSPF interface cost. This is analogous to a Hop Count in the RIP routing protocol. Restrictions Only administrator-level users can issue this command.
  • Page 200 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local>create route redistribute dst ospf src rip Command: create route redistribute dst ospf src rip Success. local> create route redistribute dst rip Purpose Used to add route redistribution settings for the exchange of OSPF routes to RIP routes on the switch.
  • Page 201 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide create route redistribute dst rip OSPF interface cost. This is analogous to a HOP Count in the RIP routing protocol. Restrictions Only administrator-level users can issue this command. Routing information source − OSPF and the Static Route table.
  • Page 202 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Example Usage: To add route redistribution settings: local>create route redistribute dst rip src ospf all metric 2 Command: create route redistribute dst rip src ospf all metric 2 Success. local> delete route redistribute...
  • Page 203 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Command: delete route redistribute dst rip src ospf Success. local> config route redistribute dst ospf Purpose Used to configure route redistribution from RIP to OSPF. Syntax config route redistribute dst ospf src [static|rip|local] {mettype [1|2]|metric <value>}...
  • Page 204 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config route redistribute dst ospf the destination device. mettype − allows the selection of one of the methods for calculating the metric value. Type-a calculates the metric (for RIP to OSPF) by adding the destination’s interface cost to the metric entered in the Metric field.
  • Page 205 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Local 0 to 16777214 Allowed Metric Type combinations are mettype 1 or mettype 2. The metric value 0 above will be redistributed in OSPF as the metric 20. Example Usage: To configure route redistributions: local>config route redistribute dst rip src ospf all metric 2...
  • Page 206 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config route redistribute dst rip various individual routers current routing protocol. switch information between the OSPF and RIP routing protocols to all routers on the network that are running OSPF or RIP.
  • Page 207 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide OSPF 0 to 16 Static 0 to 16 Entering the Type combination − internal type_1 type_2 is functionally equivalent to all. Entering the combination type_1 type_2 is functionally equivalent to external. Entering the combination internal external is functionally equivalent to all.
  • Page 208 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show route redistribute Purpose Used to display the route redistribution on the switch. Syntax show route redistribute {dst [rip|ospf]|src [rip|static|local|ospf]} Description Displays the current route redistribution settings on the switch. Parameters src − Allows the selection of the routing protocol on the source device.

  • Page 209: Igmp Commands

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide IGMP C The switch port commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters config igmp ipif <ipif_name 12> version <value 1-2>...
  • Page 210 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config igmp Purpose Used to configure IGMP on the switch. config igmp [ipif<ipif_name 12>|all] Syntax {version <value 1-2>|query_interval <sec 1-65535>|max_response_time <sec 0- 25>| robustness_variable <value 1- 255>|last_member_query_interval <sec 0- 25>|state [enabled|disabled]} Description This command is used to configure IGMP on the switch.
  • Page 211 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config igmp The default is 1 second. state [enabled|disabled] disables IGMP for the specified IP interface. Restrictions Only administrator-level users can issue this command. Example Usage: To configure the IGMP for the IP interface System: local>config igmp all version 1 state enabled...
  • Page 212 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show igmp will be displayed. Restrictions none. Example Usage: To display IGMP configurations: local>show igmp Command: show igmp IGMP Interface Configurations Interface IP Address Ver- Query Maximum Robust- Last Member State sion...
  • Page 213 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show igmp group Description This command will display the IGMP group configuration. Parameters group <group> − The multicast group ID. <ipif_name 12> − The name of the IP interface the IGMP group is part of.

  • Page 214: Igmp Snooping Commands

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide IGMP S The switch port commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters config <vlan_name 32> igmp_snooping host_timeout <sec 1-16711450>...
  • Page 215 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Command Parameters show vlan <vlan_name 32> igmp_snooping show vlan <vlan_name 32> igmp_snooping group show router_ports vlan <vlan_name 32> static dynamic Each command is listed, in detail, in the following sections. config igmp_snooping...
  • Page 216 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config igmp_snooping The default is 260 seconds. route_timeout <sec 1-16711450> − Specifies the maximum amount of time a route will remain in the switch’s can be a member of multicast receiving a host membership report. The default is 260 seconds.
  • Page 217 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config igmp_snooping querier Purpose Used to configure the time in seconds between general query transmissions, the maximum time in seconds to wait for reports from members, the permitted packet loss that guarantees IGMP snooping.
  • Page 218 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config igmp_snooping querier more members of a group on a network. This interval is calculated as follows: (robustness variable x query interval) + (1 x query response interval). • Other Amount of time that must pass...
  • Page 219 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config igmp_snooping querier querier. Restrictions Only administrator-level users can issue this command. Example Usage: To configure the IGMP snooping: local>config igmp_snooping querier default query_interval 125 state enabled Command: config igmp_snooping querier default query_interval 125 state enabled Success.
  • Page 220 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config router_ports Description This command allows you to designate a range of ports as being connected to multicast-enabled routers. This will ensure that all packets with such a router as its destination will reach the multicast-enabled router −...
  • Page 221 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local>config router_ports default add 1-10 Command: config router_ports default add 1-10 Success. local> enable igmp_snooping Purpose Used to enable IGMP snooping on the switch. Syntax enable igmp_snooping {forward-mcrouter- only} Description This command allows you to enable IGMP...
  • Page 222 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide To enable IGMP snooping on the switch: local>enable igmp_snooping Command: enable igmp_snooping Success. local> disable igmp_snooping Purpose Used to enable IGMP snooping on the switch. disable igmp_snooping Syntax Description This command disables IGMP snooping on the switch.
  • Page 223 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local>disable igmp_snooping Command: disable igmp_snooping Success. local> show igmp_snooping Purpose Used to show the current status of IGMP snooping on the switch. show igmp_snooping {vlan <vlan_name Syntax 32>} Description This command will display the current IGMP snooping configuration on the switch.
  • Page 224 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local>show igmp_snooping Command: show igmp_snooping IGMP Snooping Global State : Disabled Multicast router Only : Disabled VLAN Name : default Query Interval : 125 Max Response Time : 10 Robustness Value Last Member Query Interval...
  • Page 225 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show igmp_snooping group Purpose Used to display the current IGMP snooping group configuration on the switch. Syntax show igmp_snooping group {vlan <vlan_name 32>} Description This command will display the current IGMP snooping group configuration on the switch.
  • Page 226 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Multicast group : 234.5.6.7 MAC address : 01-00-5E-05-06-07 Reports Port Member : 26 VLAN Name : default Multicast group : 236.54.63.75 MAC address : 01-00-5E-36-3F-4B Reports Port Member : 26 VLAN Name...
  • Page 227 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show router_ports Parameters <vlan_name 32> − The name of the VLAN on which the router port resides. static − Displays router ports that have been statically configured. dynamic − Displays router ports that have been dynamically configured.
  • Page 228 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide...

  • Page 229: Commands

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide 802.1X C The DES-3350SR implements the server-side of the IEEE 802.1x Port-based Network Access Control. This mechanism is intended to allow only authorized users, or other network devices, access to network resources by establishing criteria for each port on the switch that a user or network device must meet before allowing that port to forward or receive frames.
  • Page 230 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Command Parameters server_timeout <sec 1-65535> max_req <value 1-10> reauth_period <sec 1-65535> enable_reauth [enabled|disabled] config 802.1x init port_based ports [<portlist>|all]|mac_based ports [<portlist>|all]| {mac_address <macaddr>} config 802.1x port_based ports reauth [<portlist>|all]|mac_based ports [<portlist>|all]| {mac_address <macaddr>} config 802.1x...
  • Page 231 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide enable 802.1x Purpose Used to enable the 802.1x server on the switch. Syntax enable 802.1x Description The enable 802.1x command enables the 802.1x Port-based Network Access control server application on the switch.
  • Page 232 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide disable 802.1x Description The disable 802.1x command is used to disable the 802.1x Port-based Network Access control server application on the switch. Parameters None. Restrictions Only administrator-level users can issue this command.
  • Page 233 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show 802.1x auth_configuration Port-based Network Access Control server application on the switch. Parameters ports <portlist> − Specifies a range of ports. The port list is specified by listing the lowest switch number and the beginning port number on that switch, separated by a colon.
  • Page 234 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show 802.1x auth_configuration port number displayed above. There are two 802.1x capabilities that can be set on the switch: Authentication and None. AdminCrlDir: Both|In − Shows whether a controlled Port that is unauthorized will...
  • Page 235 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show 802.1x auth_configuration Request|Identity packets. ServerTimeout − Shows the length of time to wait for a response from a Radius server. MaxReq − Shows the maximum number of times to retry sending packets to the supplicant.
  • Page 236 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide TxPeriod : 30 SuppTimeout : 30 ServerTimeout : 30 MaxReq times ReAuthPeriod : 3600 sec ReAuthenticate : Disabled show 802.1x auth_state Purpose Used to display the current authentication state of the 802.1x server on the switch.
  • Page 237 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show 802.1x auth_state Port number − Shows the physical port number on the switch. Auth PAE State: Initalize|Disconnected|Connecting| Authenticating|Authenticated|Held |ForceAuth|ForceUnauth − Shows the current state of the Authenticator PAE. Backend State: Request|Response|Fail| Idle|Initalize|Success |Timeout −...
  • Page 238 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide ForceAuth Success ForceAuth Success ForceAuth Success ForceAuth Success ForceAuth Success ForceAuth Success ForceAuth Success ForceAuth Success ForceAuth Success ForceAuth Success ForceAuth Success ForceAuth Success ForceAuth Success ForceAuth Success ForceAuth Success ForceAuth Success...
  • Page 239 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config 802.1x capability number on that switch, separated by a colon. Then highest switch number, and the highest port number of the range (also separated by a colon) are specified. The beginning and end of the port list range are separated by a dash.
  • Page 240 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config 802.1x auth_parameter Authentication parameters on a range of ports. The default parameter will return all ports in the specified range to their default 802.1x settings. config 802.1x Syntax [<portlist>|all] [both|in]|port_control [force_unauth|auto|force_auth]| quiet_period <sec 0-65535>| max_req...
  • Page 241 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config 802.1x auth_parameter direction [both|in] − Determines whether a controlled port blocks communication in both directions, or just the receiving direction. port_control administrative authentication process for the range of ports. force_auth − Forces the Authenticator for the port to become authorized.
  • Page 242 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config 802.1x auth_parameter authentication Period field, above. Restrictions Only administrator-level users can issue this command. Example Usage: To configure 802.1x authentication parameters for ports 1 to local>config 802.1x auth_parameter ports 1 – 20 direction both Command: config 802.1x auth_parameter ports 1-20 direction...
  • Page 243 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config 802.1x init <portlist> − Specifies a range of ports. The port list is specified by listing the lowest switch number and the beginning port number on that switch, separated by a colon.
  • Page 244 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config 802.1x reauth authentication feature of the switch. config 802.1x reauth port_based ports Syntax [<portlist>|all] [<portlist>|all] {mac_address <macaddr>} Description The config 802.1x reauth command is used to enable the 802.1x re-authentication feature on the switch.
  • Page 245 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Success. local> config 802.1x auth_mode Purpose Used authentication mode feature of the switch. Syntax config 802.1x reauth port_based ports [<portlist>|all] [<portlist>|all] {mac_address <macaddr>} Description The config 802.1x authentication mode command is used to enable either the port- based or MAC-based 802.1x authentication...
  • Page 246 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Example Usage: To configure the 802.1x port-based authentication mode for ports 5-6: local>config 802.1x auth_mode port_based ports 5-6 Command: config 802.1x auth_mode port_based ports 5-6 Success. local> config radius add Purpose Used to configure the settings the switch will use to communicate with a Radius server.
  • Page 247 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config radius add <passwd 32> − The shared-secret key used by the Radius server and the switch. Up to 32 characters can be used. default − Returns all of the ports in the range to their default Radius settings.
  • Page 248 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config radius delete Syntax config radius delete <server_index 1-3> Description The config radius delete command is used to delete a previously entered Radius server configuration. Parameters <server_index 1-3> − Assigns a number to the current set of Radius server settings.
  • Page 249 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config radius <udp_port_number>|acct_port <udp_port_number>} Description The config radius command is used to configure the switch’s Radius settings. Parameters <server_index 1-3> − Assigns a number to the current set of Radius server settings.
  • Page 250 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Success. local> show radius Purpose Used display configurations on the switch. Syntax show radius Description The show radius command is used to display the current Radius configurations on the switch. Parameters None.
  • Page 251 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local>...

  • Page 252: Access Control List (Acl) Commands

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide CCESS ONTROL (ACL) C The DES-3350SR implements Access Control Lists that enable the switch to deny network access to specific devices or device groups based on IP settings or MAC address. Command...
  • Page 253 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Command Parameters udp src_port_mask <hex 0x0-0xffff> dst_port_mask <hex 0x0-0xffff> protocol_id user_mask <hex 0x0-0xffffffff> permit deny profile_id <value 1-255>} delete Profile_id <value 1-255> access_profile config profile_id <value 1-255> access_profile add access_id <value 1-255>...
  • Page 254 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Command Parameters user_define <hex 0x0-0xffffffff> priority <value 0-7> replace_priority replace_dscp <value 0-63> delete <value 1-255> Due to a chipset limitation, the switch currently supports a maximum of ten access profiles, each containing a maximum of 50 rules −...
  • Page 255 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide when a logical AND operation between an IP address specified in the next step and the ip_source_mask match. The default for an access profile on the switch is to permit traffic flow. If you want to restrict traffic, you must use the deny parameter.
  • Page 256 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide create access_profile Purpose Used to create an access profile on the switch and to define which parts of each incoming frame’s header the switch will examine. Masks can be entered that will be combined with the values the switch finds in the specified frame header fields.
  • Page 257 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide create access_profile Specific values for the rules are entered using the config access_profile command, below. ethernet − Specifies that the switch will Parameters examine the layer 2 part of each packet header.
  • Page 258 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide create access_profile dscp − Specifies that the switch will examine the DiffServ Code Point (DSCP) field in each frame’s header. icmp − Specifies that the switch will examine the Internet Control Message...
  • Page 259 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide create access_profile dst_port_mask Specifies a UDP port mask for the destination port. protocol_id − Specifies that the switch will examine each frame’s Protocol ID field. user_mask Specifies that the rule applies to the IP protocol ID and the mask options behind the IP header.
  • Page 260 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Success. local> delete access_profile Purpose Used to delete a previously created access profile. delete access_profile [profile_id <value 1- Syntax 255>] Description The delete access_profile command is used to delete a previously created access profile on the swtich.
  • Page 261 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config access_profile Purpose Used to configure an access profile on the switch and to define specific values that will be used to by the switch to determine if a given packet should be forwarded or filtered.
  • Page 262 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config access_profile to configure an access profile on the switch and to enter specific values that will be combined, using a logical AND operation, with masks entered with the create access_profile command, above.
  • Page 263 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config access_profile in the packet header. ip − Specifies that the switch will look into the IP fields in each packet. vlan <vlan_name 32> − Specifies that the access profile will apply to only to this VLAN.
  • Page 264 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config access_profile have this IGMP type value. tcp − Specifies that the switch will exmamine the Transmission Control Protocol (TCP) field within each packet. src_port <value 0-65535> − Specifies that the access profile will apply only to packets that have this TCP source port in their TCP header.
  • Page 265 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config access_profile priority <value 0-7> − Specifies that the access profile will apply to packets that contain this value in their 802.1p priority field of their header. replace_priority − This parameter is specified if you want to change the 802.1p...
  • Page 266 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Success. local> show access_profile Purpose Used to display the currently configured access profiles on the switch. show access_profile Syntax Description The show access_profile command is used to display the currently configured access...
  • Page 267 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Access ID -------------------- ---------------------- 10.42.73.0...

  • Page 268: Bootp Relay Commands

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide BOOTP R The BOOTP relay commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters config bootp_relay hops <value 1-16> time <sec 0-65535>...
  • Page 269 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config bootp_relay Purpose Used to configure the BOOTP relay feature of the switch. Syntax config bootp_relay {hops <value 1-16>} {time <sec 0-65535>} Description This command is used to configure the BOOTP relay feature.
  • Page 270 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config bootp_relay add Purpose Used to add an IP destination address to the switch’s BOOTP relay table. Syntax config bootp_relay add ipif <ipif_name 12> <ipaddr> Description This command adds an IP address as a destination packets to.
  • Page 271 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config bootp_relay delete Purpose Used to delete one or all IP destination addresses from the switch’s BOOTP relay table. config bootp_relay delete ipif <ipif_name Syntax 12> <ipaddr> Description This command is used to delete one or all of the IP destination addresses in the switch’s...
  • Page 272 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide enable bootp_relay Purpose Used to enable the BOOTP relay function on the switch. enable bootp_relay Syntax Description This command, in combination with the disable bootp_relay command below, is used to enable and disable the BOOTP relay function on the switch.
  • Page 273 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide disable bootp_relay Purpose Used to disable the BOOTP relay function on the switch. Syntax disable bootp_relay Description This command, in combination with the enable bootp_relay command above, is used to enable and disable the BOOTP relay function on the switch.
  • Page 274 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show bootp_relay Description This command will display the current BOOTP relay configuration for the switch, or if an IP interface name is specified, the BOOTP relay interface. Parameters <ipif_name 12> − The name of the IP interface for which you what to display the current BOOTP relay configuration.

  • Page 275: Dns Relay Commands

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide DNS R ELAY The DNS relay commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters config dnsr primary secondary nameserver <ipaddr>...
  • Page 276 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Each command is listed, in detail, in the following sections. config dnsr Purpose Used to configure the DNS relay function. config dnsr [primary|secondary] Syntax nameserver <ipaddr> Description This command is used to configure the DNS relay function on the switch.
  • Page 277 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local> config dnsr [add|delete] static Purpose Used to add or delete a static entry into the switch’s DNS resolution table. Syntax config dnsr [add|delete] static <domain_name 32> <ipaddr> Description This command allows you to add or delete entries into the switch’s DNS cache.
  • Page 278 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local> Example Usage: To delete an entry domain name dns1, IP address 10.43.21.12 from DNS static table: local>config dnsr delete static dns1 10.43.21.12 Command: config dnsr delete static dns1 10.43.21.12 Success. local>...
  • Page 279 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local>enable dnsr Command: enable dnsr Success. local> disable dnsr Purpose Used to disable DNS relay on the switch. Syntax disable dnsr Description This command is used, in combination with the enable dnsr command above, to enable and disable DNS Relay on the switch.
  • Page 280 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide enable dnsr cache Purpose Used to enable the DNS relay cache. enable dnsr cache Syntax Description This command is used, in combination with the disable dnsr cache command below, to enable and disable the DNS relay cache.
  • Page 281 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide disable dnsr cache enable and disable the DNS relay cache. Parameters none. Restrictions Only administrator-level users can issue this command. Example Usage: To disable cache lookup for DNS relay: local>disable dnsr cache Command: disable dnsr cache Success.
  • Page 282 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide enable dnsr static this command. Example Usage: To enable static table lookup for DNS relay: local>enable dnsr static Command: enable dnsr static Success. local> disable dnsr static Purpose Used to disable the DNS relay static table.
  • Page 283 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide To disable static table lookup for DNS relay: local>disable dnsr static Command: disable dnsr static Success. local> show dnsr Purpose Used to display the current DNS relay status. show dnsr {static} Syntax...
  • Page 284 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local>show dnsr Command: show dnsr DNSR Status : Disabled Primary Name Server : 0.0.0.0 Secondary Name Server : 0.0.0.0 DNSR Cache Status : Disabled DNSR Static Table Status : Disabled DNSR Relay Static Table...

  • Page 285: Rip Commands

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide RIP C The RIP commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters config rip ipif <ipif_name 12> authentication [enabled <password 1- 16>|disabled]...
  • Page 286 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Command Parameters show rip ipif <ipif_name 12> Each command is listed, in detail, in the following sections. config rip ipif Purpose Used to configure RIP on the IP interface named “ipif” on the switch.
  • Page 287 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config rip ipif disabled transmission of RIP packets. disabled − Prevents the transmission of RIP packets. v1_only − Specifies that only RIP v1 packets will be transmitted. v2_only − Specifies that only RIP v2 packets will be transmitted.
  • Page 288 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Example Usage: To change the RIP receive mode for the IP interface System: local>config rip ipif System rx_mode v1_only Command: config rip ipif System rx_mode v1_only Success. local> config rip all Purpose Used to configure RIP on all the IP interfaces on the switch.
  • Page 289 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config rip all RIP packets. It determines how transmitted RIP packets will be interpreted–as RIP version v1 only, v2 only, or v1 compatible. disabled transmission of RIP packets. disabled − Prevents the transmission of RIP packets.
  • Page 290 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config rip all this command. Example Usage: To change the RIP state to enabled for all the IP interfaces on the switch: local>config rip all state enabled Command: config rip all state enabled Success.
  • Page 291 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide To enable RIP: local>enable rip Command: enable rip Success. local> disable rip Purpose Used to disable RIP. Syntax disable rip Description This command is used, along with the enable RIP command below, to enable or disable RIP on the switch.
  • Page 292 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show rip Purpose Used to display the RIP configuration and statistics for the switch. Syntax show rip {ipif <ipif_name 12>} Description This command configuration for a given IP interface or for all IP interfaces.
  • Page 293 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local>show rip Command: show rip RIP Interface Settings RIP Global State : Disabled Interface IP Address TX Mode -------------- ------------------- ----------------- System 10.48.74.122 V2 Only if20 20.48.74.121 Disabled Total Entries: 2 RX Mode...

  • Page 294: Dvmrp Commands

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide DVMRP C The switch port commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters config dvmrp ipif <ipif_name 12> metric <value 1-31>...
  • Page 295 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config dvmrp Purpose Used to configure DVMRP on the switch. config dvmrp [ipif <ipif_name 12>|all] Syntax {metric <value 1-31>|probe <second 1- 65535>|neighbor_timeout <second 1- 65535>|state [enabled|disabled] Description This command is used to configure DVMRP on the switch.
  • Page 296 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config dvmrp state [enabled|disabled] − Allows DVMRP to be enabled or disabled on this interface. Restrictions Only administrator-level users can issue this command. Example Usage: To configure DVMRP configurations of IP interface System: local>config dvmrp ipif System neighbor_timeout 30 metric 1...
  • Page 297 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide enable dvmrp Restrictions Only administrator-level users can issue this command. Example Usage: To enable DVMRP: local>enable dvmrp Command: enable dvmrp Success. local> disable dvmrp Purpose Used to disable DVMRP. disable dvmrp Syntax...
  • Page 298 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide To disable DVMRP: local>disable dvmrp Command: disable dvmrp Success. local> show dvmrp routing_table Purpose Used to display the current DVMRP routing table. show dvmrp Syntax <network_address>} Description The command is used to display the current DVMRP routing table.
  • Page 299 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide DVMRP Routing Table Source Address Source Mask Upstream Neighbor ----------------------- ------------------- --------------- 10.0.0.0 255.0.0.0 10.90.90.90 2 20.0.0.0 255.0.0.0 20.1.1.1 30.0.0.0 255.0.0.0 30.1.1.1 Total Entries: 3 local> show dvmrp neighbor Purpose Used to display the DVMRP neighbor table.
  • Page 300 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Example Usage: To display DVMRP neighbor table: local>show dvmrp neighbor Command: show dvmrp neighbor DVMRP Neighbor Address Table Interface Neighbor Address Generation ID --------------- ----------------------- System 10.2.1.123 Total Entries: 1 show dvmrp nexthop...
  • Page 301 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show dvmrp nexthop Restrictions none. Example Usage: To display DVMRP routing next hop table: local>show dvmrp nexthop Command: show dvmrp nexthop Source IP Address Source Mask ----------------- ---------------- 10.0.0.0 255.0.0.0 10.0.0.0 255.0.0.0 20.0.0.0...
  • Page 302 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show dvmrp interface for which you want to display the DVMRP status. Restrictions none. Example Usage: To show DVMRP configurations: local>show dvmrp Command: show dvmrp DVMRP Global State : Disabled Interface IP Address...

  • Page 303: Pim Commands

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide PIM C The PIM commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters config pim ipif <ipif_name 12> hello <sec 1-18724>...
  • Page 304 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config pim Purpose Used to configure PIM on the switch. config pim [ipif <ipif_name 12>/all] Syntax {hello <sec 1-18724>/jp_interval <sec 1- 18724>/state [enabled/disabled]} Description This command is used to configure PIM on the switch.
  • Page 305 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local>config pim ipif System hello 35 jp_interval 70 state enabled Command: config pim ipif System hello 35 jp_interval 70 state enabled Success. local> enable pim Purpose Used to enable PIM on the switch.
  • Page 306 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local> disable pim Purpose Used to disable PIM on the switch. disable pim Syntax Description This command, in combination with the enable pim command above, is used to enable or disable PIM on the switch.
  • Page 307 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show pim neighbor Syntax show 12>/ipaddress <ipaddr>} Description This command will display the current PIM neighbor router table. Parameters <ipif_name 12> − The name of the IP interface for which you want to display the current PIM neighbor routing table.
  • Page 308 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show pim Purpose Used configuration. show pim {ipif <ipif_name 12>} Syntax Description This command will display the current PIM configuration. <ipif_name 12> − The name of the IP Parameters interface for which you want to display the PIM configuration for.
  • Page 309 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local>...

  • Page 310: Ip Multicasting Commands

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide IP M ULTICASTING The IP multicasting commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters show ipmc cache group <group> ipaddress <network_address>...
  • Page 311 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show ipmc cache Description This command will display the current IP multicast forwarding cache. Parameters group <group> − The multicast group ID. ipaddress <network_address> address and netmask of the destination. You can specify the IP address and netmask...
  • Page 312 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show ipmc Purpose Used to display the IP multicast interface table. Syntax show ipmc {ipif <ipif_name 12>|protocol [dvmrp|pim]} Description This command will display the current IP multicast interface table. Parameters <ipif_name 12> − The name of the IP interface for which you want to display the IP multicast interface table for.
  • Page 313 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local>show ipmc Command: show ipmc Interface IP Address Multicast Routing --------------- --------------- ----------------- System 10.90.90.90 Total Entries: 1 local> INACT...

  • Page 314: Md5 Configuration Commands

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide MD5 C ONFIGURATION The MD5 configuration commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters config md5 key <key_id 1-255> <password 16>...
  • Page 315 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config md5 Purpose Used to enter configure an MD5 key and password. Syntax config md5 <key_id 1-255> <password 16> Description This command is used to configure an MD5 key and password. Parameters <key_id 1-255>...
  • Page 316 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide create md5 Purpose Used to create an MD5 key table. create Syntax <password 16> Description This command is used to create an MD5 key table. <key_id 1-255> − The MD5 key ID.
  • Page 317 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide delete md5 Purpose Used to delete an MD5 key table. delete md5 key <key_id 1-255> Syntax Description This command is used to delete an MD5 key table. <key_id 1-255> − The MD5 key ID.
  • Page 318 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show md5 Restrictions none. Usage Example To display the current MD5 key: local>show md5 Command: show md5 MD5 Key Table Key-ID ------ ---------- dlink develop fireball intelligent Total Entries: 4 local>...

  • Page 319: Ospf Configuration Commands

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide OSPF C ONFIGURATION The OSPF configuration commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters config ospf <ipaddr> router_id enable ospf...
  • Page 320 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Command Parameters create ospf <ipaddr> host_route area <area_id> metric <value 1-65535> delete ospf <ipaddr> host_route config ospf <ipaddr> host_route area <area_id> metric <value> show ospf <ipaddr> host_route create ospf <area_id> aggregation <network_address>...
  • Page 321 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Command Parameters area <area_id> priority <value> hello_interval <sec 1-65535> dead_interval <sec 1-65535> authentication [none|simple <password>| md5 <key_id 1-255>] metric <value 1-65535> state [enabled|disabled] show ospf ipif <ipif_name 12> show ospf all create ospf <area_id>...
  • Page 322 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config ospf Purpose Used to configure the OSPF router ID. config ospf router_id <ipaddr> Syntax Description This command is used to configure the OSPF router ID. <ipaddr> − The OSPF router ID.
  • Page 323 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide enable ospf this command. Usage Example To enable OSPF on the switch: local>enable ospf Command: enable ospf Success. local> disable ospf Purpose Used to disable OSPF on the switch. disable ospf Syntax...
  • Page 324 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local> show ospf Purpose Used to display the current OSPF state on the switch. show ospf Syntax Description This command will display the current state of OSPF on the switch, divided into the...
  • Page 325 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide OSPF Router ID : 10.1.1.2 State : Enabled OSPF Interface Settings Interface IP Address Area ID ------------ ------------------ --------- System 10.90.90.90|8 0.0.0.0 20.1.1.1|8 0.0.0.0 30.1.1.1|8 0.0.0.0 Total Entries : 3 OSPF Area Settings...
  • Page 326 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide OSPF Area Aggregation Settings Area ID Aggregated LSDB Network Address Type --------------- ------------------ -------- Total Entries : 0 OSPF Host Route Settings Host Address Metric Area ID --------------- ------ --------------- 10.3.3.3 10.1.1.1 Total Entries : 1 local>...
  • Page 327 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide create ospf area stub or normal. stub_summary − Enables or disables the OSPF area advertisements. metric <value 0-16777215> − The OSPF area cost between 0 and 16,777,215. The default is 1. Restrictions Only administrator-level users can issue this command.
  • Page 328 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide delete ospf area Parameters <area_id> − <area_id> − A 32-bit number in the form of an IP address (xxx.xxx.xxx.xxx) that uniquely identifies the OSPF area in the OSPF domain. Restrictions Only administrator-level users can issue this command.
  • Page 329 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config ospf area type − Allows the specification of the OSPF mode of operation − stub or normal. stub_summary [enabled|disabled] − Allows the OSPF area import of LSA advertisements to be enabled or disabled.
  • Page 330 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show ospf Description This command will display the current OSPF area configuration. Parameters <area_id> − A 32-bit number in the form of address uniquely identifies the OSPF area in the OSPF domain.
  • Page 331 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide create ospf host_route Description This command is used to configure the OSPF host route settings. Parameters <ipaddr> − The host’s IP address. area <area_id> − A 32-bit number in the form of an IP address (xxx.xxx.xxx.xxx) that uniquely identifies the OSPF area in the OSPF domain.
  • Page 332 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide delete ospf host_route Syntax delete ospf host_route <ipaddr> Description This command is used to delete an OSPF host route. Parameters <ipaddr> − The IP address of the OSPF host. Restrictions Only administrator-level users can issue this command.
  • Page 333 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config ospf host_route <area_id> − <area_id> − A 32-bit number in the form of an IP address (xxx.xxx.xxx.xxx) that uniquely identifies the OSPF area in the OSPF domain. metric <value 1-65535> − A metric between 1 and 65,535, which will be advertised.
  • Page 334 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show ospf host_route Parameters <ipaddr> − The IP address of the host. Restrictions none. Usage Example: To display the current OSPF host route table: local>show ospf host_route Command: show ospf host_route Host Address...
  • Page 335 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide create ospf aggregation Description This command is used to create an OSPF area aggregation. Parameters <area_id> − A 32-bit number in the form of address uniquely identifies the OSPF area in the OSPF domain.
  • Page 336 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local>...
  • Page 337 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide delete ospf aggregation Purpose Used to delete an OSPF area aggregation configuration. Syntax delete ospf aggregation <area_id> <network_address> lsdb_type [summary] Description This command is used to delete an OSPF area aggregation configuration.
  • Page 338 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Success. local> config ospf aggregation Purpose Used to configure the OSPF area aggregation settings. Syntax config ospf aggregation <area_id> <network_address> lsdb_type [summary] advertise [enabled|disabled] Description This command is used to configure the OSPF area aggregation settings.
  • Page 339 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Usage Example: To configure the OSPF area aggregation settings: local>config ospf aggregation 10.1.1.1 10.48.76.122/16 lsdb_type summary advertise enabled Command: config ospf aggregation 10.1.1.1 10.48.76.122/16 lsdb_type summary advertise enabled Success. local> show ospf aggregation...
  • Page 340 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide OSPF Area Aggregation Settings Area ID Aggregated LSDB Network Address Type ------------ --------------------- -------------- ------------- 10.1.1.1 10.0.0.0|8 Summary 10.1.1.1 20.2.0.0|16 Summary Total Entries: 2 local> show ospf lsdb Purpose Used to display the OSPF Link State Database (LSDB).
  • Page 341 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show ospf lsdb Restrictions none. Note: When this command displays a “ OSPF LSDB table for the Area_id or the Cost, this is interpreted as “no area ID” for external LSAs, and as “no cost given”...
  • Page 342 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show ospf neighbor router table. Syntax show ospf neighbor {<ipaddr>} Description This command will display the current OSPF neighbor router table. Parameters <ipaddr> − The IP address of the neighbor router. Restrictions none.
  • Page 343 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show ospf virtual_neighbor <neighbor_id>} Description This command will display the current OSPF virtual neighbor router table. <area_id> − A 32-bit number in the form of Parameters address uniquely identifies the OSPF area in the OSPF domain.
  • Page 344 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config ospf ipif Purpose Used configure settings. Syntax config ospf [ipif <ipif_name 12>/all {area <area_id>|priority <value>|hello_interval <sec 1-65535>|dead_interval <sec 1- 65535>|authentication [none|simple <password 8>|md5 <key_id 1- 255>]|metric <value>|state [enabled|disabled]} Description This command is used to configure the OSPF interface settings.
  • Page 345 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config ospf ipif the receipt of Hello packets from a neighbor router before the selected area declares that router down. An interval between 1 and 65535 seconds can be specified. The Dead Interval must be evenly divisible by the Hello Interval.
  • Page 346 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show ospf ipif Purpose Used to display the current OSPF interface settings for the specified interface name. Syntax show ospf ipif {<ipif_name 12>} Description This command will display the current OSPF interface settings for the specified interface name.
  • Page 347 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local> show ospf all Purpose Used to display the current OSPF settings of all the OSPF interfaces on the switch. Syntax show ospf all Description This command will display the current OSPF settings for all OSPF interfaces on the switch.
  • Page 348 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Interface Name: ipif2 (Link Up) Network Medium Type: BROADCAST Area ID: 1.0.0.0 Priority: 1 DR Address: 123.234.12.34 Hello Interval: 10 Transmit Delay: 1 Authentication: None Total Entries: 2 local> config ospf virtual_link...
  • Page 349 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config ospf virtual_link Parameters <area_id> − A 32-bit number in the form of address uniquely identifies the OSPF area in the OSPF domain. <neighbor_id> − The OSPF router ID for the remote area. This is a 32-bit number (xxx.xxx.xxx.xxx) that uniquely identifies...
  • Page 350 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config ospf virtual_link Restrictions Only administrator-level users can issue this command. Usage Example: To configure the OSPF virtual interface settings: local>config ospf virtual_link 10.1.1.2 20.1.1.1 hello_interval 10 Command: config ospf virtual_link 10.1.1.2 20.1.1.1 hello_interval Success.
  • Page 351 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide create ospf virtual_link <area_id> − A 32-bit number in the form of Parameters address uniquely identifies the OSPF area in the OSPF domain. <neighbor_id> − The OSPF router ID for the remote area. This is a 32-bit number (xxx.xxx.xxx.xxx) that uniquely identifies...
  • Page 352 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide create ospf virtual_link Restrictions Only administrator-level users can issue this command. Usage Example: To create an OSPF virtual interface: local>create ospf virtual_link 10.1.12 20.1.1.1 hello_interval 10 Command: create ospf virtual_link 10.1.12 20.1.1.1 hello_interval 10 Success.
  • Page 353 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide delete ospf virtual_link the remote area. This is a 32-bit number (xxx.xxx.xxx.xxx) that uniquely identifies the remote area’s Area Border Router. The router ID of the neighbor router. Restrictions Only administrator-level users can issue this command.
  • Page 354 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide show ospf virtual_link OSPF domain. <neighbor_id> − The OSPF router ID for the remote area. This is a 32-bit number (xxx.xxx.xxx.xxx) that uniquely identifies the remote area’s Area Border Router. This is the router ID of the neighbor router.

  • Page 355: Sntp Commands

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide SNTP C The Simple Network Time Protocol (SNTP) (an adaptation of the Network Time Protocol (NPT)) commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table.
  • Page 356 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config sntp Syntax config sntp Description This command is used to configure SNTP on the switch. Parameters primary − This is the primary server the SNTP information will be taken from. <ipaddr> − The IP address of the primary server.
  • Page 357 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local>config sntp primary 10.24.22.5 Command: config sntp primary 10.24.22.5 Success. local> enable sntp Purpose Used to enable SNTP on the switch. Syntax enable sntp Description This command enables SNTP on a switch.
  • Page 358 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide disable sntp Purpose Used to disable SNTP on the switch. disable sntp Syntax Description This command will disable SNTP on the switch. Parameters None. Restrictions None. Example Usage: To disable SNTP on the switch: local>disable sntp...
  • Page 359 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Parameters None. Restrictions None. Example Usage: To show SNTP on the switch: local>show sntp Command: show sntp Current Time Source : System Clock SNTP : Disabled SNTP Primary Server : 10.24.22.5 SNTP Secondary Server : 0.0.0.0 SNTP poll interval : 720 sec local>...

  • Page 360: Command History List

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide OMMAND The switch port commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters show command_history config <value 1-40> command_history Each command is listed, in detail, in the following sections.
  • Page 361 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Description This command will display all of the commands Command Line Interface (CLI). Parameters none. Restrictions none. Usage Example To display all of the commands in the CLI: local>? Command: ? clear...
  • Page 362 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config arp_aging time config arpentry CTRL+C ESC q Quit SPACE n Next Page show command_history Purpose Used to display the command history. Syntax show command_history Description This command will display the command history.
  • Page 363 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide config router_ports vlan2 add config router_ports vlan2 config router_ports show vlan create vlan vlan2 tag 3 create vlan vlan2 tag 2 show router_ports show router ports login local> Purpose Used to display all commands.
  • Page 364 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide clear log config 802.1p default_priority config 802.1p user_priority config 802.1x auth_mode config 802.1x auth_parameter ports config 802.1x capability ports config 802.1x init config 802.1x reauth config access_profile profile_id config account config aggport...
  • Page 365 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide local>config command_history 20 Command: config command_history 20 Success. local>...

  • Page 366: Technical Specifications

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide PECIFICATIONS General Standards: IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3z 1000BASE-SX Gigabit Ethernet IEEE 802.3ab 1000BASE-T Gigabit Ethernet IEEE 802.1 P|Q VLAN IEEE 802.3 Nway auto-negotiation Protocols: CSMA|CD...

  • Page 367: Physical And Environmental

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide General Network Cables: 10BASE-T: 2-pair UTP Cat. 3,4,5 (100 m) EIA|TIA- 568 100-ohm STP (100 m) 100BASE-TX: 2-pair UTP Cat. 5 (100 m) EIA|TIA-568 100-ohm STP (100 m) Mini GBIC: IEC 793-2:1992 Type A1a - 50|125um multimode Type A1b - 62.5|125um multimode...
  • Page 368 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Physical and Environmental mount width Weight: 4.4 kg EMI: FCC Class A, CE Class A, BSMI Class A, C-Tick Class A Safety: CSA International Performance Transmission Method: Store-and-forward RAM Buffer: 64M Bytes per device...

  • Page 369: Switch System Messages

    DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide WITCH Message “Success.” “Error applying data!” "Invalid IP address!” “Invalid subnet mask!” “Invalid gateway address!” “All changes are saved!” "Invalid MAC address!” "No more MAC-Based VLANs can be added!” "No more MAC addresses can be added!”...
  • Page 370 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide "Flow Control is not Enabled!” "Spanning tree group name cannot be empty!” "The IP interface must be deleted first!” "The system interface is not in manual mode!” "The VLAN already has a IP Interface!”...
  • Page 371 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide "The EEPROM is full!” "The VLAN has no router ports.” "IGMP snooping is disabled in the designated VLAN.” "The username is invalid.” "Incorrect password” "The specified user already exists. Enter a unique username.”...
  • Page 372 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide "Duplicate route! Enter a unique route.” "Target port can't be source port!” "This port member can't be set.” "Port members must belong to the same VLAN.” "The target port can't be selected as a mirror port.”...
  • Page 373 DES-3350SR Layer 3 Fast Ethernet Switch User’s Guide Maxmum Variable Name Length <username> <password> <ipaddr> <netmask> <gateway> <vlan_name> <sw_name> <sw_location> <sw_contact> Password <community_string> <server_ip> <path_filename> <macaddr> <ipif> Type String String IP-Address IP-Address IP-Address String String String String String String IP-Address...
  • Page 374 TEL: 1-905-829-5033 FAX: 1-905-829-5095 BBS: 1-965-279-8732 TOLL FREE: 1-800-354-6522 URL: www.dlink.ca FTP: ftp.dlinknet.com E-MAIL: techsup@dlink.ca Chile D-Link South America Isidora Goyenechea 2934 Of. 702, Las Condes Fono, 2323185, Santiago, Chile, S. A. TEL: 56-2-232-3185 FAX: 56-2-232-0923 URL: www.dlink.cl E-MAIL: ccasassu@dlink.cl & tsilva@dlink.cl...
  • Page 375 Le Florilege, No. 2, Allea de la Fresnerie, 78330 Fontenay Le Fleury, France TEL: 33-1-3023-8688 FAX: 33-1-3023-8689 URL: www.dlink-france.fr E-MAIL: info@dlink-france.fr Germany D-Link Central Europe|D-Link Deutschland GmbH Schwalbacher Strasse 74, D-65760 Eschborn, Germany TEL: 49-6196-77990 FAX: 49-6196-7799300 URL: www.dlink.de BBS: 49-(0) 6192-971199 (analog) BBS: 49-(0) 6192-971198 (ISDN)
  • Page 376 D-Link South Africa Unit 2, Parkside, 86 Oak Avenue, Highveld Technopark, Centurion, Gauteng, South Africa TEL: 27 (0) 12-665-2165 FAX: 27 (0) 12-665-2186 URL: www.d-link.co.za E-MAIL: attie@d-link.co.za Spain D-Link Iberia C|Sabino De Arana, 56 Bajos, 08028 Barcelona, Spain TEL: 34 93 4090770 FAX: 34 93 4910795 URL: www.dlinkiberia.es E-MAIL: info@dlinkiberia.es...
  • Page 377 U.S.A. D-Link U.S.A. 53 Discovery Drive, Irvine, CA 92618, USA TEL: 1-949-788-0805 FAX: 1-949-753-7033 BBS: 1-949-455-1779 & 1-949-455-9616 INFO: 1-800-326-1688 URL: www.dlink.com E-MAIL: tech@dlink.com & support@dlink.com...

  • Page 378: Registration Card

    Engineering Education Finance Retail|Chainstore|Wholesale Government Transportation|Utilities|Communication System house|company Other________________________________ 9. Would you recommend your D-Link product to a friend? Don't know yet 10.Your comments on this product? __________________________________________________________________________________________ __________________________________________________________________________________________ * Product installed in computer serial No. Personal Use 1000 or more...

Table of Contents