Table of Contents
Advertisement
Programming EasyTouch: Remote Controls
iS4 Spa-Side Remote Controller
You can specify any iS4 Spa-Side remote button to control different functions by assigning each button to
a specific circuit. For example, you can use the iS4 Spa-Side remote to activate the spa circulation and for
operating auxiliary equipment such as heater, lights, jet pump, heat boost, air blower, waterfall, etc.). You
can also use the "Pump Incrs" and "Pump Decrs" circuit to increase or decrease the pump speed for an
IntelliFlo VF (GPM) or VS (RPM) pump. For example, if the "Pump Incrs" circuit is assigned to an iS4 button,
each press of the button will increase the pump speed in specific speed increments as specified in the "10 B
Pump Cntrl" menu setting (see page 50). Speed increments are set from 10 to 250 RPM (or 1 to 10 GPM, for
the IntelliFlo VF).
To assign iS4 Spa-Side buttons:
Getting There
MENU
SETTINGS
iS4
ASSIGN iS4
Assign iS4
Circuit: 1/4
[HEAT BOOST ]
SpaCommand 10 Button Spa-Side Remote Controller
From this menu you can assigning a specific circuit to any one of the ten buttons of an iS10 and
SpaCommand spa-side remote to control different pool/spa functions. The iS10 and SpaCommand has ten
assignable circuit buttons; five button on the top row and five buttons on the bottom row. You can also use
the "Pump Incrs" and "Pump Decrs" circuit to increase or decrease the pump speed for an IntelliFlo VF
(GPM), VS (RPM) and VSF (RPM/GPM) pump. For example, if the "Pump Incrs" circuit is assigned to an iS10
button, each press of the button will increase the pump speed in specific speed increments as specified in
the "10B Pump Cntrl" menu setting (see page 43). Speed increments are set from 10 to 250 RPM (or 1 to 10
GPM, for the IntelliFlo VF).
Assign 10 Button Spa Side Remote (iS10/SpaCommand)
Getting There
MENU SETTINGS 10 BUTN SPA SD ASSIGN 10 BUTN
Before configuring the 10 button spa-side remote controller (iS10/SpaCommand) assign names to the
circuits (see page 30).
Up/Down buttons: Select a circuit to one of the iS4 buttons. You can set up to four
circuits (1/4, 2/4, 3/4, 4/4).
Right button: Move to the circuit setting.
Up/Down buttons: To configure the first button on the iS4 Spa-Side Remote,
scroll through the circuit names and find the circuit that you would like to assign
to the first button on the iS4. The generic circuits are: NONE, SPA, POOL, AUX
1-7 (EasyTouch PNP 10), AUX 1-3 (EasyTouch PNP 5), FEATURE 1-8, SOLAR (if
selected in "Heat" menu), AUX EXTRA, HEAT BOOST, HEAT ENABLED, PUMP
INCRS, PUMP DECRS. Selecting "NONE" does not assign a circuit.
Note: The "HEAT BOOST" feature will switch on the heater for seven minutes
to increase the spa water temperature. Each time the spa Heat Boost button is
pressed, the temperature will increase about 1
beyond the 40°C limit.
Right button: Assign the next circuit (2/4).
Up/Down buttons: Select the first digit for the circuit number (1/4, 2/4, 3/4, 4/4)
and repeat the procedure for the other three buttons.
Press the Menu button to save the settings and to return to the Settings menu
options. Press the button again to return to the main menu options or press again
to return to the main screen.
°
Page 42
C. The temperature will not go
Advertisement
Table of Contents
