Directed XPRESSSTART ONE Installation Manual page 21

9 OEM Alarm Disarm
Output
10 OEM Alarm Disarm
Pulses
11 Aux 1 Icon
12 Aux 1 Output Type
13 Aux 1 Linking
14 Aux 1 Timed Output
15 Aux 2 Icon
16 Aux 2 Output Type
17 Aux 2 Linking
18 Aux 2 Timed Output
19 Aux 3 Icon
20 Aux 3 Output Type
21 Aux 3 Linking
22 Aux 3 Timed Output
23 Aux 4 Icon
24 Aux 4 Output Type
25 Aux 4 Linking
26 Aux 4 Timed Output
27 Aux/Trunk Icon
28 Aux/Trunk Output Type
29 Remote keypad unlock-
ing
30 Transmitter Programming
31 OEM Alarm Disarm With
Unlock
21
With Unlock: OEM Alarm Disarm wire will pulse as programmed concurrently with unlock wire.
1.
2. Before Unlock: OEM Alarm Disarm wire will pulse as programmed before the unlock wire.
3. Remote start only: OEM Alarm Disarm wire will pulse as programmed during remote start only.
1. 1: OEM Alarm Disarm wire will pulse once per operation.
2. 2: OEM Alarm Disarm wire will pulse twice per operation.
Sets the Accessory animation to be displayed on the screen when the Aux 1 output is activated/deacti-
vated:
Trunk 7.
1.
2. Window 8.
3. Sunroof 9.
10. Pulsed
4. Audio
5. Lights 11. Garage door
6. Left door
1. Validity: when the Aux command is received the wire will turn and remain on until the command
ceases.
2. Latch: when the command is received the wire will turn and remain on until the command is received
again.
3. Latch/reset/Ignition: when the command is received the wire will turn and remain on until the com-
mand is received again or the ignition is turned on/off.
4. Timed: when the command is received the wire will turn on for the programmed time duration (default
is 30 seconds).
5. Off: the output will not be activated for a remote control command; use this option when the Aux
command controls an external device, such as a garage door module.
1. No Linking: Aux output will NOT be activated for a remote control command.
2. Link to Arm: output will be activated for the Arm command.
3. Link to Disarm: output will be activated for the Disarm command.
4. Link to Arm/Disarm: output will be activated for the Arm/Disarm commands.
5. Link to Remote Start Only: output will be activated for any remote start activation.
Sets the output duration in seconds, with a maximum of 90 seconds. *The default value is 30 seconds.
Refer to the Aux 1 Icon description.
Refer to Aux 1 Output Type description.
Refer to Aux 1 Linking description.
Refer to Aux 1 Timed Output description.
Refer to the Aux 1 Icon description.
Refer to Aux 1 Output Type description.
Refer to Aux 1 Linking description.
Refer to Aux 1 Timed Output description.
Refer to the Aux 1 Icon description.
Refer to Aux 1 Output Type description.
Refer to Aux 1 Linking description.
Refer to Aux 1 Timed Output description.
Refer to Aux 1 Icon description. The default value is Trunk.
Validity
1.
2. Off
Off: no message is sent.
1.
2. On: a message telling the 2-way remote control to unlock the keypad is sent each time the vehicle
ignition is turned off.
Locks/unlocks the user's ability to enter the HHU/Reset menu and manually change any functions using the
Control Center. The default value is Unlocked.
Disable
1.
2. Enable
Right door
Rear hatch
Timed
XpressStart ONE 4x10/5x10 Analog
© 2013 Directed. All rights reserved.