Advertisement
Quick Links
FACTORY HARNESS WITH
BLUE SHELL FITTED
XPRESS
BLACK PLUG
The XPRESSSTART Mercedes Solution is designed as a direct plug in interface to the rear of the Mercedes Benz key cylinder. Please
WHITE PLUG
read this manual in it's entirety prior to installation as there is a specific order of operation that needs to be followed.
Tools and Parts you will need:
•
T-20 driver
•
Drill
•
3/4" drill bit or Unibit
GREEN PLUG
WHITE PLUG
ML & GL Installation
1.
Remove (3) T-20 screws from the driver's under dash panel.
2.
Lower dash panel down and move air vent out of the clips that hold it in place.
3.
Reach up to the rear of the EIS. There are two retaining clips on the top and bottom of the EIS.
4.
Grasp the wiring harness while squeezing the retaining clips together to remove the EIS.
5.
Pull the EIS with harness attached out of the dash to access the wiring.
6.
Unplug both plugs (blue and green) from the EIS.
© 2012 Directed. All rights reserved.
REMOVE WHITE SHELL
AND REPLACE WITH
PROVIDED BLUE SHELL
WHITE 10 PIN PLUG
(BLACK INSERT WITH
WHITE OUTER SHELL)
FIT ORIGINAL WHITE
SHELL TO THE
PROVIDED T-HARNESS
DIGITAL RemoTe sTART sysTem
SUPPLIED T-HARNESS
www
xpResskIT
com
.
.
START Mercedes Solution
BLACK PLUG
Installation Instructions
2012+ Mercedes Benz ML Class
WHITE PLUG
2013+ Mercedes Benz GL Class
2013 Mercedes Benz G Class
SUPPLIED T-HARNESS
XPRESSSTART Wiring Overview
GREEN PLUG
BLUE PLUG
SUPPLIED T-HARNESS
EIS
(KEY CYLINDER)
EIS
(KEY CYLINDER)
XPRESSSTART
mADe IN THe UsA
EIS
(KEY CYLINDER)
EIS
(KEY CYLINDER)
XPRESSSTART
W/X166
EIS
(KEY CYLINDER)
EIS
(KEY CYLINDER)
XPRESSSTART
BEFORE INSTALLATION
AFTER INSTALLATION
VALET SWITCH
BEFORE INSTALLATION
AFTER INSTALLATION
VALET SWITCH
BEFORE INSTALLATION
AFTER INSTALLATION
VALET SWITCH
QRNMB166 2012-12
1
Advertisement
Related Manuals for Directed XpressSTART Mercedes Solution
Summary of Contents for Directed XpressSTART Mercedes Solution
- Page 1 AFTER INSTALLATION (KEY CYLINDER) The XPRESSSTART Mercedes Solution is designed as a direct plug in interface to the rear of the Mercedes Benz key cylinder. Please WHITE PLUG read this manual in it’s entirety prior to installation as there is a specific order of operation that needs to be followed.
- Page 2 Remove (3) T-20 Remove (3) T-20 Lower panel and move vent Lower panel and move vent Remove (3) T-20 Lower panel and move vent EIS removed EIS removed T-harness installed T-harness installed EIS removed T-harness installed © 2012 Directed. All rights reserved.
- Page 3 Remove steering wheel boot EIS plug location at rear of EIS EIS plug location at rear of EIS Remove steering wheel boot EIS plug location at rear of EIS Copyright 2012 Midcity Engineering® Copyright 2012 Midcity Engineering® © 2012 Directed. All rights reserved.
- Page 4 2012+ ML, 2013+ GL W/X166 KeylessGo Connection The KeylessGo connection for the 2012 ML is quite involved and requires significant disassembly of the rear of the vehicle. This guide assumes the basic XPRESSSTART Mercedes Solution is installed and functioning properly. Tools and Parts you will need: •...
- Page 5 " " Unbolt seat back Unbolt cargo tie downs" " " " " Remove cargo cover Unbolt cargo tie downs" " " " " Remove cargo cover Unbolt cargo tie downs Remove cargo cover © 2012 Directed. All rights reserved.
- Page 6 Flip seat back into cargo area Pull up carpet Pull up carpet" " Pull up carpet" " " " " " " " " " " " Unplug KeylessGo module Unplug KeylessGo module Unplug KeylessGo module © 2012 Directed. All rights reserved.
- Page 7 " " " " " " " " Plug KeylessGo module in New pins installed, reinstall shroud Plug KeylessGo module in " " New pins installed, reinstall shroud © 2012 Directed. All rights reserved. " " Plug KeylessGo module in...
- Page 8 Remove seat belt Remove door sill Remove seat belt Remove screw cover" " Remove screw cover" " " " " " " " " " Remove T-30 Remove T-30 Remove screw cover Remove T-30 © 2012 Directed. All rights reserved.
- Page 9 Shroud removed" " " " " " KG harness properly installed into plug Shroud removed Shroud removed" " " " " " KG harness properly installed into plug KG harness properly installed into plug © 2012 Directed. All rights reserved.
- Page 10 DSM200 or DSM250). The cable can be plugged directly in to the port. The power and ground must be connected The (3) pin connector is designed to accept the ESP cable that comes with the Directed SmartStart module (DSM100, DSM200 or (soldered and taped) to the XPRESSSTART harness.