Siemens SED2 Commissioning Manual page 69

Unit: - Min: -
Bit fields:
Bit00 Fixed frequency Bit 0
Bit01 Fixed frequency Bit 1
Bit02 Fixed frequency Bit 2
Bit03 Fixed frequency Bit 3
Bit08 PID enabled
Bit09 DC brake enabled
Bit11 Droop
Bit12 Not used
Bit13 External fault 1
r0056 CO/BO: Status of motor control
Displays status of motor control (V/f status), which can be used to diagnose VSD status.
Unit: - Min: -
Bit fields:
Bit00 Init. control finished
Bit01 Motor demagnetizing finished
Bit02 Pulses enabled
Bit03 Voltage soft start select
Bit04 Motor excitation finished
Bit05 Starting boost active
Bit06 Acceleration boost active
Bit07 Frequency is negative
Bit08 Field weakening active
Bit09 Volts setpoint limited
Bit10 Slip frequency limited
Bit11 F_out > F_max
Bit12 Phase reversal selected
Bit13 I-max controller active
Bit14 Vdc-max controller active
Bit15 Vdc-min controller active
r0061 CO: Act. rotor speed
Displays current speed detected by encoder.
Unit: Hz Min: -
r0086 CO: Act. active current
Displays active (real part) of motor current.
Unit: A Min: -
Dependency: Applies when V/f control is selected in P1300 (control mode); otherwise, the display shows the value zero.
P0100 Europe / North America
Determines whether power settings (e.g. nominal rating plate power - P0307) are expressed in
[kW] or [hp].
The default settings for the nominal rating plate frequency (P0310) and maximum motor
frequency (P1082) are also set automatically here, in addition to reference frequency (P2000).
Unit: - Min: 0
Settings: 0=Europe [kW], frequency default 50 Hz
1=North America [hp], frequency default 60 Hz
2=North America [kW], frequency default 60 Hz
Dependency: The setting of DIP switch 2 under the I/O module determines the validity of settings 0 and 1 for P0100 according to the
following table:
DIP 2 Setting
Off
On
Stop VSD first (i.e. disable all pulses) before you change this parameter.
P0010=1 (commissioning mode) enables changes to be made.
Changing P0100 resets all rated motor parameters as well as other parameters that depend on the rated motor
parameters (see P0340 - calculation of motor parameters).
Note: P0100 setting 2 (==> [kW], frequency default 60 [Hz]) is not overwritten by the setting of DIP switch 2 (see table above.)
r0200 Act. power stack code number
Identifies hardware variant.
Unit: - Min: -
Note: Parameter r0200=0 indicates that no power stack has been identified.
r0206 Rated VSD power [kW] / [hp]
Displays nominal rated motor power from the VSD.
Unit: - Min: -
Dependency: Value is displayed in [kW] or [hp], depending on setting for P0100 (operation for Europe / North America).
r0207 Nominal motor current
Displays maximum continuous output current of the VSD.
Unit: A Min: -
r0208 Rated VSD voltage
Displays nominal AC supply voltage of the VSD.
Unit: V Min: -
Value: r0208=230 : 200 - 240 V +/- 10%
Siemens
Building Technologies
Def: -
Def: -
Freq. limited
Def: -
Def: -
Def: 0
Meaning
[kW], frequency default 50 [Hz]
[hp], frequency default 60 [Hz]
Def: -
Def: -
Def: -
Def: -
r0208=400 : 380 - 480 V +/- 10%
Commissioning Guide
10 Parameterization
Max: -
0 NO, 1 YES
0 NO, 1 YES
0 NO, 1 YES
0 NO, 1 YES
0 NO, 1 YES
0 NO, 1 YES
0 NO, 1 YES
0 NO, 1 YES
0 YES, 0 NO
Max: -
0 NO, 1 YES
0 NO, 1 YES
0 NO, 1 YES
0 NO, 1 YES
0 NO, 1 YES
0 NO, 1 YES
0 NO, 1 YES
0 NO, 1 YES
0 NO, 1 YES
0 NO, 1 YES
0 NO, 1 YES
0 NO, 1 YES
0 NO, 1 YES
0 NO, 1 YES
0 NO, 1 YES
0 NO, 1 YES
Max: -
Max: -
Max: 2
P0100 Setting
Overwrites 1
Overwrites 0
Max: -
Max: -
Max: -
Max: -
Level 3
Level 3
Level 3
Level 1
Meaning
[hp], frequency default 60 [Hz]
[kW], frequency default 50 [Hz]
Level 3
Level 3
Level 3
Level 3
r0208=575 : 500 - 600 V +/- 10%
CM1G5192en
29.07.2010
69 / 100