Siemens SED2 Commissioning Manual page 68

r0035 CO: Act. motor temperature
Displays calculated motor temperature.
Unit: °C Min: -
r0039 CO: Energy consumption meter [kWh]
Displays electrical energy used by VSD since display was last reset (see P0040 - reset energy
consumption meter).
Unit: kWh Min: -
Dependency: Value is reset when P3900=1 (end quick commissioning), P0970=1 (factory reset) or P0040=1 (reset energy
consumption meter).
P0040 Reset energy consumption meter
Resets value of parameter r0039 (energy consumption meter) to zero.
Unit: - Min: 0
Settings: 0=No reset
Dependency: No reset until P is pressed
r0052 CO/BO: Act. status word 1
Displays first active status word of VSD (bit format) and can be used to diagnose VSD status.
Unit: - Min: -
Bit fields:
Bit00 VSD ready
Bit01 VSD ready to run
Bit02 VSD running
Bit03 VSD fault active
Bit04 OFF2 active
Bit05 OFF3 active
Bit06 ON inhibit active
Bit07 VSD warning active
Bit08 Deviation setp/act value
Bit09 PZD control
Bit10 Maximum frequency reached
Bit11 Warning: Motor current limit
Bit12 Motor holding brake active
Bit13 Motor overload
Bit14 Motor runs direction right
Bit15 VSD overload
Note: Output of Bit3 (Fault) will be inverted on digital output high=no fault).
r0053 CO/BO: Act. status word 2
Displays second status word of VSD (in bit format).
Unit: - Min: -
Bit fields:
Bit00
Bit01
Bit02
Bit03
Bit04
Bit05
Bit06
Bit07
Bit08
Bit09
Bit10
Bit11
Bit12
Bit13
Bit14
Bit15
r0054 CO/BO: Act. control word 1
Displays first control word of VSD and can be used to diagnose which commands are active.
Unit: - Min: -
Bit fields:
Bit00
Bit01
Bit02
Bit03
Bit04
Bit05
Bit06
Bit07
Bit08
Bit09
Bit10
Bit11
Bit13
Bit14
Bit15
r 0055 CO/BO: Add. act. control word
Displays additional control word of VSD and can be used to diagnose which commands are
active.
68 / 100
Siemens
Building Technologies
Def: -
Def: -
Def: 0
Def: -
Def: -
DC brake active
Act. freq. r0021 >
Act. freq. r0021 >
Act. current r0027 >= P0305
Act. freq. r0021 >
Act. freq. r0021 <= P2155 (f_1)
Act. freq. r0021 >= setpoint
Act. Vdc r0026
Act. Vdc r0026
Ramping finished
PID output r2294
PID output r2294
Reserved
Reserved
Download data set 0 from AOP
Download data set 1 from AOP
Def: -
ON/OFF1
OFF2: Electrical stop
OFF3: Fast stop
Pulse enable
RFG enable
RFG start
Setpoint enable
Fault acknowledge
JOG right
JOG left
Control from PLC
Reverse (setpoint inversion)
Motor potentiometer MOP up
Motor potentiometer MOP down
CDS Bit 0 (Local/Remote – Hand/Auto) 0
Commissioning Guide
10 Parameterization
Max: -
Max: -
Max: 1
1=Reset r0039 to 0
Max: -
0 NO, 1 YES
0 NO, 1 YES
0 NO, 1 YES
0 NO, 1 YES
0 YES, 1 NO
0 YES, 1 NO
0 NO, 1 YES
0 NO, 1 YES
0 YES, 1 NO
0 NO, 1 YES
0 NO, 1 YES
0 YES, 1 NO
0 NO, 1 YES
0 YES, 1 NO
0 NO, 1 YES
0 YES, 1 NO
Max: -
0
P2167 (f_off) 0
P1080 (f_min) 0
0
P2155 (f_1) 0
0
0
< 800 V 0
> 800 V 0
0
= P2292 (PID_min) 0
= P2291 (PID_max) 0
0 NO, 1
0 NO, 1
Max: -
0 NO, 1
0 YES, 1
0 YES, 1
0 NO, 1
0 NO, 1
0 NO, 1
0 NO, 1
0 NO, 1
0 NO, 1
0 NO, 1
0 NO, 1
0 NO, 1
0 NO, 1
0 NO, 1
NO, 1
NO, 1 YES
NO, 1 YES
NO, 1 YES
NO, 1 YES
NO, 1 YES
NO, 1 YES
NO, 1 YES
NO, 1 YES
NO, 1 YES
NO, 1 YES
NO, 1 YES
NO, 1 YES
YES
YES
YES
NO
NO
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
Level 3
Level 3
Level 3
Level 3
Level 3
Level 3
Level 3
CM1G5192en
29.07.2010